An LED is a device that emits light when electrically biased. Similar to any electronic component, LEDs also have electrical parameters that need to be taken into consideration when designed into a system.
2. Introduction
LED-Chip Reflector
A Light Emitting Diode (LED) is Wire Bond Mold
a device that emits light when
electrically biased.
Lead frame
Similar to any electronic
component,
component LEDs also have
electrical parameters that need
to be taken into consideration Silicone
when designing with LEDs.
Bond
Wire
LEDs are very similar to Chip
standard diodes and most of the
electrical characteristics of
standard diodes also apply to Cavity
LEDs. 0.25
0 25 mm
Here is a simple picture to show
how LEDs are constructed.
constructed
Printed Circuit Board (PCB)
3. How does an LED emit light?
n-Crystal
n Cr stal p-Crystal
p Crystal +
Metallic Contact
- + Epitaxy Layer
Depletion zone
Substrate
-
Electrons
Holes
LED chip‘s PN junction is biased in a forward direction;
Free charge is forced (overcome Vf) into the depletion zone;
Electrons recombine with holes, and some of these recombination's emit light;
The color of the light is based on the material selection, which directly affects the
forward voltage of the LED.
4. Electrical parameters of an LED
The following electrical parameters should be taken in to consideration when designing
with LEDs.
1. Vf and current: the I-V curve of the LED will have these information
2. Pulse d
2 P l and surge current of th LED
t f the
3. Reverse current and/ or reverse voltage
4. Junction temperature (Tj)
a.
a reduction in Vf due to Tj
b. shift in color due to Tj
c. flux degradation due to Tj
5.
5 Recommended PCB foot print
foot-print
5. Forward Voltage - Vf
Similar to standard diodes, in LEDs,
nothing happens until a threshold voltage is
reached. Once the threshold is reached,
current through the LED rapidly increases
with increasing voltage.
Due to this behavior the preferred method
to drive the LED is with constant current.
As it can be seen from the graph on the
right, nothing happens until the threshold
voltage of ~2.75V. Once the 2.7V is
reached, current th
h d t through th LED
h the
increases exponentially with slight increase
in voltage.
6. LED current (forward current)
LED current is one of the key parameters as it determines the amount of light that the
LED puts out, the forward voltage of the LED, and the color or wavelength shift when
the LEDs is driven, in a particular design, at a different current than the binning current.
The Vf of an LED varies slightly depending on the LED current. As LEDs are driven
current
using constant current, if the system has a resistor type current regulation, an accurate
Vf should be used to calculate the resistor value.
The color shift due to different LED current also determines what dimming methodology
to be utilized in a system, if the system requires some kind of dimming. If color shift is
due to analog dimming, (where LED DC current is varied to achieve different dimming
levels), is not acceptable, PWM (Pulse Width Modulation) dimming should be utilized.
LED current also determines the efficacy of the LED as well as the system efficacy.
7. LED current (forward current) …
Shown on the right is the relative flux vs
LED current.
Since the binning current for this LED is
350mA, the flux at 350mA is x 1 in a
relative graph.
When the LED current is 700mA the flux
700mA,
will be ~1.74 times that of the flux at
350mA.
Wh d i i an LED system, th LED
When designing t the
current will determine the total flux/ light
output of the system, along with some
other key parameters of the system.
8. LED current (forward current) …
Efficacy of an LED with respect to
LED current is shown on the right.
Th efficacy of an LED decreases as
The ffi f d
LED current is increased.
It is required to consider this
phenomenon when designing an LED
system as this will impact the overall
system efficacy.
9. LED current (forward current) …
There will be a slight color shift due to
LED current, if the LED current is different
from the binning current.
As it can be seen in the graph on the
right, there will be no shift at 350mA
because that is the binning current.
At 700 A one should expect t see a Cy
700mA, h ld t to C
shift of ~0.0075 and a Cx shift of ~0.003
on the CIE 1931 diagram.
This particular characteristics of an LED
will eventually determine the dimming
methodology, if the system requires some
kind of dimming.
10. Pulse and Surge current
Surge current is the absolute maximum non-
DC current th t th LED can h dl Th
t that the handle. The
maximum surge current and the definition of
it should be taken in to consideration when
designing with LEDs.
The definition of surge can be represented
as:
t < 50mS, D=0.016, and Ts=25°C
where Ts is the solder point temperature.
The frequency and the duty cycle of the
pulse current is very important and should be
considered during system design.
Also, note that the definition of pulse can
vary at different solder point temperatures
temperatures.
11. Reverse current/ voltage – IR / VR
Reverse current and/ or the reverse voltage of an LED is one of the critical parameters
to be considered when designing with LEDs
LEDs.
Most LEDs are not designed to be operated in the reverse direction.
Also, because of how the protection device within an LED is oriented (see below), care
should be taken when the LEDs are placed in anti-parallel manner.
Since LEDs are not designed for reverse operation, negative spikes within the circuit
should be taken into account to ensure the LEDs are properly operated.
12. Junction temperature - Tj
The junction temperature of the LED is a
key factor of the life of an LED.
In terms of electrical characteristics of an
LED, junction temperature plays a role on
the forward voltage of the LED (Vf), pulsed
current, flux reduction, and color shift.
As demonstrated in the graph, Vf reduces
when Tj increases. This should be
considered when using a resistor to regulate
LED the current.
current
13. Junction temperature – Tj …
The graph on the right shows the flux
reduction when Tj increases. Even though
this may not be considered an electrical
parameter, it will impact the electrical
parameters indirectly.
Flux degradation at higher Tj can be
compensated with LED current and when
the LED current is changed many of the
changed,
other electrical parameters of an LED are
impacted.
For this and other reasons such as Vf drop
and color shift, Tj should be taken into
consideration when finalizing other
electrical parameters.
14. Junction temperature – Tj …
As demonstrated in the chart, the
color shift due to Tj may be significant
and needs to be taken in to
consideration during the design
g g
process.
15. PCB footprint
The PCB footprint may not be
considered an electrical
parameter, but is included here
because it can impact the
electrical characteristics.
Shown on the right is the
recommended footprint for
OSRAM s
OSRAM’s OSLON package
package.
Proper footprint is required for
proper thermal management of
the LED and ease of assembly,
including correct placement and
reflow of the LED.
16. Disclaimer
All information contained in this document has been checked with the greatest care
care.
OSRAM Opto Semiconductors GmbH and its affiliates and subsidiaries can however,
not be made liable for any damage that occurs in connection with the use of these
contents.
OSRAM Opto Semiconductor GmbH and its affiliates and subsidiaries makes no
representations and warranties as to a possible interference with third parties'
intellectual property rights in view of p
p p y g products originating from one of OSRAM Opto
g g p
Semiconductor GmbH's partners, or in view of products being a combination of an
OSRAM Opto Semiconductor GmbH's product and a product of one of OSRAM Opto
Semiconductor GmbH's partners. Furthermore, OSRAM Opto Semiconductors GmbH
and its affiliates and subsidiaries cannot be made liable for any damage that occurs in
y g
connection with the use of a product of one of OSRAM Opto Semiconductor GmbH's
partners, or with the use of a combination of an OSRAM Opto Semiconductor GmbH's
product and a product of one of OSRAM Opto Semiconductor GmbH's partners.