More Related Content Similar to Catalogo Cables Radiantes, Leaky Radiating Cables (20) Catalogo Cables Radiantes, Leaky Radiating Cables2. Radiating and Coupling Cable Systems
Radiating cables are used wherever normal radio communication is difficult or impossible,
in particular in communication systems where a discrete antenna would not provide
adequate coverage, such as in tunnels, underground railways, mines, buildings, etc.
RF energy is simultaneously transmitted down radiating
cables and radiated from all points along them into the
surrounding space.
Slots cut into the outer conductor of the coaxial cable
allow controlled levels of electromagnetic energy to be
radiated both out of and into the cable.
Cables Characteristics
Radiating Cable 1/2" Radiating Leaky Feeder Slexrtd RF 450-2600 MHz
Radiating Cable 1/2" Radiating Leaky Feeder Silexrtd RF 150-900 MHz
Radiating Cable 1/2" Coupling Leaky Feeder Silexrtd RF 75-2400 MHz
Radiating Cable 1/2" Coupling2 Leaky Feeder Silexrtd RF 75-2400 MHz
Radiating Cable 7/8" Radiating Leaky Feeder Slexrtd RF 75-2700 MHz
Radiating Cable 7/8" Radiating Leaky Feeder Slexrtd RF 75-960 MHz
Radiating Cable 7/8" Coupling Leaky Feeder Slexrtd RF 75-2400 MHz
Radiating Cable 7/8" Coupling2 Leaky Feeder Slexrtd RF 75-2400 MHz
Radiating Cable 1-1/4" Radiating Leaky Feeder Slexrtd RF 75-2700 MHz
Radiating Cable 1-1/4" Radiating Leaky Feeder Slexrtd RF 75-960 MH
Radiating Cable 1-1/4" Coupling Leaky Feeder Slexrtd RF 75-2400 MHz
Radiating Cable 1-5/8" Radiating Leaky Feeder Slexrtd RF 75-2700 MHz
Radiating Cable 1-5/8" Radiating Leaky Feeder Slexrtd RF 75-2500 MHz
Radiating Cable 1-5/8" Radiating Leaky Feeder Slexrtd RF 75-960 MHz
Radiating Cable 1-5/8" Coupling Leaky Feeder Slexrtd RF 75-2400 MHz
Connectors Systems
Radiating Connector DIN 7/16 Type
Radiating Connector N Type
Radiating Clamp Systems Fix
Metalic System Camp
Plastic System Camp
3. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our Radiating series focus on some Specific band which can provide an optimized performance. They are popularly
used in GSM/CDMA/UMTS system.
RCF12R26(Z)(R)
Coaxial Radiating Cable, Broadband from 450 –2600 MHz, 1/2 in,
Low smoke, black non-halogenated or fire retardant polyolefin
jacket.
Type HLCAY(Z)(R)-50-12(1/2"C)
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 1/2"
Inner Conductor Diameter 4.80 mm | 0.1890"
Dielectric Diameter 12.30 mm | 0.4843"
Outer Conductor Diameter 12.60 mm | 0.4961"
Diameter Over Jacket 15.50 mm | 0.6102"
Inner Conductor Copper-Clad Aluminum Wire
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket Black PE or Low Smoke Halogen-free Fire-retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 125 mm
Multiple bending radius 350 mm
Minimum Distance to Wall 50 mm
Tensile Strength 1000 N
Bending Moment 13.5N.m
Flat Plate Crush Strength 200kg/m
Recommended Hanger
Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
4. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 75.0 pF/m
Impedance 50±2 Ω
Velocity 86%
Insulation Resistance >5000 MΩ•km
Jacket Spark 8 KV
Insulation Voltage 6 KV
Inner Conductor DC Resistance 1.60 Ω/km
Outer Conductor DC Resistance 4.30 Ω/km
Stop Band 1012~1052MHz & 2025~2110MHz
Operating Frequency Band 700~2700 MHz
VSWR
800~960 MHz ≤1.30
1700~2025 MHz ≤1.40
2110~2170 MHz ≤1.40
2300~2700 MHz ≤1.40
ELECTRICAL PERFORMANCE
Frequency Attenuation
Coupling Loss
(2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
450 005 1,58 82 90
800 007 2,19 69 73
900 008 2,35 68 72
1800 012 3,63 65 68
2000 013 3,96 67 70
2100 014 4,18 65 69
2200 014 4,27 65 68
2400 016 4,72 63 66
2600 016 4,91 64 68
5. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
RLK12R9(Z)(R)
Coaxial Radiating Cable, Broadband from 150 –900 MHz, 1/2 in, Low
smoke, black non-halogenated or fire retardant polyolefin jacket.
Type HLCAY(Z)(R)-50-12(1/2"D)
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 1/2"
Inner Conductor Diameter 4.80 mm | 0.1890"
Dielectric Diameter 12.30 mm | 0.4843"
Outer Conductor Diameter 12.60 mm | 0.4961"
Diameter Over Jacket 15.50 mm | 0.6102"
Inner Conductor Copper-Clad Aluminum Wire
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket Black PE or Low Smoke Halogen-free Fire-retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 125 mm
Multiple bending radius 350 mm
Minimum Distance to Wall 50 mm
Tensile Strength 1000 N
Bending Moment 13.5N.m
Flat Plate Crush Strength 200kg/m
Recommended Hanger
Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
6. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 75.0 pF/m
Impedance 50±2 Ω
Velocity 88%
Insulation Resistance >5000 MΩ•km
Jacket Spark 8 KV
Insulation Voltage 6 KV
Inner Conductor DC Resistance 1.48 Ω/km
Outer Conductor DC Resistance 3.40 Ω/km
VSWR
0.3 ~ 0.5 GHz ≤1.30
0.8 ~ 1.0 GHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation
Coupling Loss
(2m)
MHz dB/100 m 50%(dB) 95%(dB)
150 3.30 62 70
450 5.90 65 70
800 8.40 64 70
900 9.10 63 70
7. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our coupling series can support all major services from 75 MHz to 3 GHz and is therefore optimally suited for
multi-operator and multi-band applications.
RCF12C24(Z)
Coaxial Radiating Cable, Broadband from 75 –2400 MHz, 1/2 in, Low
smoke, black non-halogenated or fire retardant polyolefin jacket.
Type HLCAY(Z)-50-12(1/2")
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 1/2"
Inner Conductor Diameter 4.80 mm | 0.1890"
Dielectric Diameter 12.30 mm | 0.4843"
Outer Conductor Diameter 13.80 mm | 0.4961"
Diameter Over Jacket 15.70 mm | 0.6102"
Inner Conductor Copper-Clad Aluminum Wire
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket Black PE or Low Smoke Halogen-free Fire-retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 50mm
Multiple bending radius 350 mm
Minimum Distance to Wall 50 mm
Tensile Strength 1000 N
Bending Moment 13.5N.m
Flat Plate Crush Strength 200kg/m
Recommended Hanger
Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
8. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 76.0 pF/m
Impedance 50±2 Ω
Velocity 86%
Insulation Resistance >5000 MΩ•km
Jacket Spark 8 KV
Insulation Voltage 6 KV
Inner Conductor DC Resistance 1.50 Ω/km
Outer Conductor DC Resistance 3.00 Ω/km
Stop Band -
Operating Frequency Band 75~2400 MHz
VSWR
0.3~0.5 GHz ≤1.30
0.8~1.0 GHz ≤1.30
1.7~2.7GHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation COUPLING LOSS(2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 2,1 0,6 69 77
150 3 0,9 70 80
450 5,5 1,7 70 80
800 7,5 2,3 72 83
900 8,1 2,5 72 83
1800 12,4 3,8 77 86
2200 13,9 4,2 78 87
2400 14,5 4,4 78 86
9. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our coupling series can support all major services from 75 MHz to 3 GHz and is therefore optimally suited for
multi-operator and multi-band applications.
RCF12C224(Z)
Coaxial Radiating Cable, Broadband from 75 –2400 MHz, 1/2 in, Low
smoke, black non-halogenated or fire retardant polyolefin jacket.
Type HLCAY(Z)-50-12(1/2")
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 1/2"
Inner Conductor Diameter 4.80 mm | 0.1890"
Dielectric Diameter 12.30 mm | 0.4843"
Outer Conductor Diameter 13.80 mm | 0.4961"
Diameter Over Jacket 15.70 mm | 0.6102"
Inner Conductor Copper-Clad Aluminum Wire
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket Black PE or Low Smoke Halogen-free Fire-retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 50mm
Multiple bending radius 350 mm
Minimum Distance to Wall 50 mm
Tensile Strength 1000 N
Bending Moment 13.5N.m
Flat Plate Crush Strength 200kg/m
Recommended Hanger
Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
10. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 76.0 pF/m
Impedance 50±2 Ω
Velocity 88%
Insulation Resistance >5000 MΩ•km
Jacket Spark 8 KV
Insulation Voltage 6 KV
Inner Conductor DC Resistance 1.50 Ω/km
Outer Conductor DC Resistance 3.10 Ω/km
Stop Band -
Operating Frequency Band 75~2400 MHz
VSWR
0.3~0.5 GHz ≤1.30
0.8~1.0 GHz ≤1.30
1.7~2.7GHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation COUPLING LOSS(2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 2,1 0,63 66 76
150 03 0,94 67 78
450 5,7 1,74 67 78
800 7,9 2,41 71 80
900 8,2 2,5 70 80
1800 12,9 3,93 69 81
2200 14,5 4,42 72 82
2400 15,5 4,72 75 83
11. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our Radiating series focus on some Specific band which can provide an optimized performance. They are popularly
used in GSM/CDMA/UMTS system.
RCF78R27(Z)(R)
Coaxial Radiating Cable, Broadband from 75 –2700 MHz, 7/8” in,
Low smoke, black non-halogenated or fire retardant polyolefin
jacket.
Type HLCTY(Z)(R)-50-23(7/8"C)
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 7/8"
Inner Conductor Diameter 9.45 mm | 0.3720"
Dielectric Diameter 22.80 mm | 0.8976"
Outer Conductor Diameter 23.50 mm | 0.9370"
Diameter Over Jacket 27.20 mm | 1.0709"
Inner Conductor Smooth Copper Tube
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket
Black PE or Low Smoke Halogen-free Fire-
retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 250 mm
Multiple bending radius 500 mm
Minimum Distance to Wall 50 mm
Tensile Strength 1350 N
Bending Moment 14.9N.m
Flat Plate Crush Strength 400kg/m
Recommended Hanger Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
12. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 75.0 pF/m
Impedance 50±2 Ω
Velocity 89%
Insulation Resistance >5000 MΩ•km
Jacket Spark 8 KV
Insulation Voltage 10 KV
Inner Conductor DC Resistance 1.80 Ω/km
Outer Conductor DC Resistance 2.90 Ω/km
Stop Band 1012~1052MHz & 2025~2110MHz
Operating Frequency Band 75~2700 MHz
Optimum Operating Frequency Band 700~2700 MHz
VSWR
800~960 MHz ≤1.30
1700~2025 MHz ≤1.30
2110~2170 MHz ≤1.30
2300~2700 MHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation Coupling Loss (2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 001 000 70 79
100 002 0,46 70 81
150 002 0,55 78 89
350 003 0,88 83 93
450 003 1,04 85 95
700 004 1,19 73 77
800 004 1,22 70 73
900 004 1,28 69 72
1800 007 1,98 65 68
1900 007 002 64 67
2200 008 2,38 63 66
2400 008 003 62 65
2600 009 2,87 62 66
2700 011 3,23 62 66
13. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our Radiating series focus on some Specific band which can provide an optimized performance. They are popularly
used in GSM/CDMA/UMTS system.
RLK78R10(Z)(R)
Coaxial Radiating Cable, Broadband from 75 –960 MHz, 7/8” in, Low
smoke, black non-halogenated or fire retardant polyolefin jacket.
Type HLCTY(Z)(R)-50-23(7/8"D)
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 7/8"
Inner Conductor Diameter 9.45 mm | 0.3720"
Dielectric Diameter 22.80 mm | 0.8976"
Outer Conductor Diameter 23.20 mm | 0.9134"
Diameter Over Jacket 27.20 mm | 1.0709"
Inner Conductor Smooth Copper Tube
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket
Black PE or Low Smoke Halogen-free Fire-
retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 250 mm
Multiple bending radius 500 mm
Minimum Distance to Wall 50 mm
Tensile Strength 1350 N
Bending Moment 14.9N.m
Flat Plate Crush Strength 400kg/m
Recommended Hanger Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
14. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 75.0 pF/m
Impedance 50±2 Ω
Velocity 89%
Insulation Resistance >5000 MΩ•km
Jacket Spark 8 KV
Insulation Voltage 10 KV
Inner Conductor DC Resistance 1.80 Ω/km
Outer Conductor DC Resistance 3.00 Ω/km
Stop Band 180~280MHz & 500~580MHz
Operating Frequency Band 75~1000 MHz
VSWR
800~960 MHz ≤1.30
1700~2025 MHz ≤1.30
2110~2170 MHz ≤1.30
2300~2700 MHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation Coupling Loss (2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 001 000 60 70
100 002 0,49 62 65
150 002 0,58 63 73
350 003 0,91 62 65
450 004 1,07 66 71
650 004 1,25 61 68
800 005 1,43 60 62
900 005 1,52 58 61
960 005 1,62 57 60
15. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our coupling series can support all major services from 75 MHz to 3 GHz and is therefore optimally suited for
multi-operator and multi-band applications.
RCF78C24(Z)(R)
Coaxial Radiating Cable, Broadband from 75 –2400 MHz, 7/8 in, Low
smoke, black non-halogenated or fire retardant polyolefin jacket.
Type HLCTY(Z)-50-22(7/8")
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 7/8"
Inner Conductor Diameter 9.00 mm |
Dielectric Diameter 22.30 mm |
Outer Conductor Diameter 24.90 mm |
Diameter Over Jacket 27.50 mm |
Inner Conductor Smooth Copper Tube
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket Black PE or Low Smoke Halogen-free Fire-retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 90mm
Multiple bending radius 500 mm
Minimum Distance to Wall 50 mm
Tensile Strength 1470 N
Bending Moment 14.9N.m
Flat Plate Crush Strength 400kg/m
Recommended Hanger
Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
16. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 76.0 pF/m
Impedance 50±2 Ω
Velocity 86%
Insulation Resistance >5000 MΩ•km
Jacket Spark 8 KV
Insulation Voltage 6 KV
Inner Conductor DC Resistance 1.65 Ω/km
Outer Conductor DC Resistance 1.90 Ω/km
Stop Band -
Operating Frequency Band 75~2400 MHz
VSWR
0.3~0.5 GHz ≤1.30
0.8~1.0 GHz ≤1.30
1.7~2.7GHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation COUPLING LOSS(2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 1,2 0,4 63 72
150 2 0,5 65 75
450 3,2 1 71 79
800 4,4 1,3 75 83
900 4,7 1,4 76 85
1800 7,1 2,2 77 87
2200 8 2,4 78 86
2400 8,9 2,7 77 87
17. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our coupling series can support all major services from 75 MHz to 3 GHz and is therefore optimally suited for
multi-operator and multi-band applications.
RCF78C224(Z)
Coaxial Radiating Cable, Broadband from 75 –2400 MHz, 7/8 in, Low
smoke, black non-halogenated or fire retardant polyolefin jacket.
Type HLCTY(Z)-50-22-2(7/8")
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 7/8"
Inner Conductor Diameter 9.00 mm |
Dielectric Diameter 22.30 mm |
Outer Conductor Diameter 24.90 mm |
Diameter Over Jacket 27.50 mm |
Inner Conductor Smooth Copper Tube
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket Black PE or Low Smoke Halogen-free Fire-retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 90mm
Multiple bending radius 500 mm
Minimum Distance to Wall 50 mm
Tensile Strength 1470 N
Bending Moment 14.9N.m
Flat Plate Crush Strength 400kg/m
Recommended Hanger
Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
18. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 76.0 pF/m
Impedance 50±2 Ω
Velocity 86%
Insulation Resistance >5000 MΩ•km
Jacket Spark 8 KV
Insulation Voltage 10 KV
Inner Conductor DC Resistance 1.65 Ω/km
Outer Conductor DC Resistance 2.10 Ω/km
Stop Band -
Operating Frequency Band 75~2400 MHz
VSWR
0.3~0.5 GHz ≤1.30
0.8~1.0 GHz ≤1.30
1.7~2.7GHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation COUPLING LOSS(2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 1,2 0,4 63 72
150 2 0,5 65 75
450 3,2 1 71 79
800 4,4 1,3 75 83
900 4,7 1,4 76 85
1800 7,1 2,2 77 87
2200 8 2,4 78 86
2400 8,9 2,7 77 87
Maximum attenuation value shall be 105% of the nominal attenuation value
19. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our Radiating series focus on some Specific band which can provide an optimized performance. They are popularly
used in GSM/CDMA/UMTS system.
RCF114R27(Z)(R)
Coaxial Radiating Cable, Broadband from 75 –2700 MHz, 1-1/4” in,
Low smoke, black non-halogenated or fire retardant polyolefin
jacket.
Type HLCTY(Z)(R)-50-32(1-1/4"C)
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 1-1/4"
Inner Conductor Diameter 13.00 mm | 0.5118"
Dielectric Diameter 32.80 mm | 1.2913"
Outer Conductor Diameter 33.20 mm | 1.3071"
Diameter Over Jacket 37.80 mm | 1.5039"
Inner Conductor Smooth Copper Tube
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket
Black PE or Low Smoke Halogen-free Fire-
retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 400 mm
Multiple bending radius 800 mm
Minimum Distance to Wall 50 mm
Tensile Strength 2500 N
Bending Moment 15.5N.m
Flat Plate Crush Strength 1000kg/m
Recommended Hanger Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
20. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 75.0 pF/m
Impedance 50±2 Ω
Velocity 89%
Insulation Resistance >5000 MΩ•km
Jacket Spark 8 KV
Insulation Voltage 10 KV
Inner Conductor DC Resistance 1.00 Ω/km
Outer Conductor DC Resistance 2.40 Ω/km
Stop Band 1012~1052MHz & 2025~2110MHz
Operating Frequency Band 75~2700 MHz
Optimum Operating Frequency Band 700~2700 MHz
VSWR
800~960 MHz ≤1.30
1700~2025 MHz ≤1.30
2110~2170 MHz ≤1.30
2300~2700 MHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation Coupling Loss (2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 001 0,24 70 78
100 001 000 69 79
150 001 0,34 80 90
350 002 0,55 84 94
450 002 0,61 83 94
700 003 0,82 75 79
800 003 0,88 70 73
900 003 0,94 69 72
1800 005 1,62 66 69
1900 006 1,77 66 68
2200 006 1,95 65 68
2400 007 2,19 63 66
2600 008 2,41 64 67
2700 009 2,62 63 66
21. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our Radiating series focus on some Specific band which can provide an optimized performance. They are popularly
used in GSM/CDMA/UMTS system.
RLK114R10(Z)(R)
Coaxial Radiating Cable, Broadband from 75 –960 MHz, 1-1/4” in,
Low smoke, black non-halogenated or fire retardant polyolefin
jacket.
Type HLCTY(Z)(R)-50-32(1-1/4"D)
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 1-1/4"
Inner Conductor Diameter 13.00 mm | 0.5118"
Dielectric Diameter 32.80 mm | 1.2913"
Outer Conductor Diameter 33.20 mm | 1.3071"
Diameter Over Jacket 37.80 mm | 1.5039"
Inner Conductor Smooth Copper Tube
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket
Black PE or Low Smoke Halogen-free Fire-
retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 400 mm
Multiple bending radius 800 mm
Minimum Distance to Wall 50 mm
Tensile Strength 2500 N
Bending Moment 15.5N.m
Flat Plate Crush Strength 1000kg/m
Recommended Hanger Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
22. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 75.0 pF/m
Impedance 50±2 Ω
Velocity 89%
Insulation Resistance >5000 MΩ•km
Jacket Spark 10 KV
Insulation Voltage 10 KV
Inner Conductor DC Resistance 1.00 Ω/km
Outer Conductor DC Resistance 2.40 Ω/km
Stop Band 180~280MHz & 500~580MHz
Operating Frequency Band 75~1000 MHz
VSWR
75~150 MHz ≤1.30
300~500 MHz ≤1.30
600~750 MHz ≤1.30
806~960 MHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation Coupling Loss (2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 001 0,24 63 73
100 001 000 64 74
150 001 0,37 65 76
350 002 0,58 64 68
450 002 0,64 67 72
650 003 0,82 65 69
800 003 0,94 59 61
900 003 1,04 58 60
960 004 1,19 58 62
23. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our coupling series can support all major services from 75 MHz to 3 GHz and is therefore optimally suited for
multi-operator and multi-band applications.
RCF114C24(Z)
Coaxial Radiating Cable, Broadband from 75 –2400 MHz, 1-1/4 in,
Low smoke, black non-halogenated or fire retardant polyolefin
jacket.
Type HLCTY(Z)-50-32(1-1/4")
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 7/8"
Inner Conductor Diameter 13.00 mm |
Dielectric Diameter 32.50 mm |
Outer Conductor Diameter 35.80 mm |
Diameter Over Jacket 38.60 mm |
Inner Conductor Smooth Copper Tube
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket Black PE or Low Smoke Halogen-free Fire-retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 150mm
Multiple bending radius 700 mm
Minimum Distance to Wall 50 mm
Tensile Strength 2900 N
Bending Moment 15.5N.m
Flat Plate Crush Strength 1000kg/m
Recommended Hanger
Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
24. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 76.0 pF/m
Impedance 50±2 Ω
Velocity 88%
Insulation Resistance >5000 MΩ•km
Jacket Spark 10 KV
Insulation Voltage 10 KV
Inner Conductor DC Resistance 1 Ω/km
Outer Conductor DC Resistance 1 Ω/km
Stop Band -
Operating Frequency Band 75~2400 MHz
VSWR
0.3~0.5 GHz ≤1.30
0.8~1.0 GHz ≤1.30
1.7~2.7GHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation COUPLING LOSS(2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 0,8 0,24 61 71
150 1,1 0,34 64 74
450 2,5 0,76 75 85
800 3,3 1,01 76 86
900 3,5 1,07 76 86
1800 5 1,52 77 87
2200 5,9 1,8 77 87
2400 6,5 1,98 78 88
Maximum attenuation value shall be 105% of the nominal attenuation value
25. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our Radiating series focus on some Specific band which can provide an optimized performance. They are popularly
used in GSM/CDMA/UMTS system.
RCF158R27(Z)(R)
Coaxial Radiating Cable, Broadband from 75 –2700 MHz, 1-5/8” in,
Low smoke, black non-halogenated or fire retardant polyolefin
jacket.
Type HLHTY(Z)(R)-50-42(1-5/8"C1)
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 1-5/8"
Inner Conductor Diameter 17.40 mm | 0.6850"
Dielectric Diameter 42.80 mm | 1.6850"
Outer Conductor Diameter 43.50 mm | 1.7126"
Diameter Over Jacket 48.00 mm | 1.8898"
Inner Conductor Helical Copper Tube
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket
Black PE or Low Smoke Halogen-free Fire-
retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 510 mm
Multiple bending radius 900 mm
Minimum Distance to Wall 50 mm
Tensile Strength 3000 N
Bending Moment 16.0N.m
Flat Plate Crush Strength 1500kg/m
Recommended Hanger Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
26. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 75.0 pF/m
Impedance 50±2 Ω
Velocity 89%
Insulation Resistance >5000 MΩ•km
Jacket Spark 10 KV
Insulation Voltage 15 KV
Inner Conductor DC Resistance 1.50 Ω/km
Outer Conductor DC Resistance 1.50 Ω/km
Stop Band 1012~1052MHz & 2025~2110MHz
Operating Frequency Band 75~2700 MHz
Optimum Operating Frequency Band 700~2700 MHz
VSWR
75~150 MHz ≤1.30
800~960 MHz ≤1.30
1700~2025 MHz ≤1.30
2110~2170 MHz ≤1.30
2300~2700 MHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation Coupling Loss (2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 001 0,18 70 79
100 001 0,24 70 81
150 001 0,27 78 90
350 001 000 83 93
450 002 0,46 83 94
700 002 0,58 74 77
800 002 0,64 70 72
900 002 001 69 71
1800 004 1,19 64 68
1900 004 1,28 63 66
2000 004 1,34 63 66
2200 005 1,46 63 65
2400 005 1,62 62 64
2600 006 1,83 63 65
2700 007 002 63 66
27. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our Radiating series focus on some Specific band which can provide an optimized performance. They are popularly
used in GSM/CDMA/UMTS system.
RCF158R25(Z)(R)
Coaxial Radiating Cable, Broadband from 75 –2500 MHz, 1-5/8” in,
Low smoke, black non-halogenated or fire retardant polyolefin
jacket.
Type HLHTY(Z)(R)-50-42(1-5/8"C2)
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 1-5/8"
Inner Conductor Diameter 17.40 mm | 0.6850"
Dielectric Diameter 42.80 mm | 1.6850"
Outer Conductor Diameter 43.50 mm | 1.7126"
Diameter Over Jacket 48.00 mm | 1.8898"
Inner Conductor Helical Copper Tube
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket
Black PE or Low Smoke Halogen-free Fire-
retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 510 mm
Multiple bending radius 900 mm
Minimum Distance to Wall 50 mm
Tensile Strength 3000 N
Bending Moment 16.0N.m
Flat Plate Crush Strength 1500kg/m
Recommended Hanger Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
28. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 75.0 pF/m
Impedance 50±2 Ω
Velocity 89%
Insulation Resistance >5000 MΩ•km
Jacket Spark 10 KV
Insulation Voltage 15 KV
Inner Conductor DC Resistance 1.50 Ω/km
Outer Conductor DC Resistance 1.50 Ω/km
Stop Band 1012~1052MHz & 2025~2110MHz
Operating Frequency Band 75~2500 MHz
Optimum Operating Frequency Band 700~2500 MHz
VSWR
800~960 MHz ≤1.30
1700~2025 MHz ≤1.30
2110~2170 MHz ≤1.30
2300~2700 MHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation Coupling Loss (2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 001 0,18 70 79
100 001 0,24 70 81
150 001 0,27 78 90
350 001 000 83 93
450 002 0,46 83 94
700 002 0,58 74 77
800 002 0,64 67 68
900 002 001 66 68
1800 004 1,22 62 65
1900 004 1,31 63 65
2000 005 001 61 63
2100 005 1,46 59 62
2200 005 1,62 59 62
2400 006 1,89 57 61
2500 007 002 57 62
29. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our Radiating series focus on some Specific band which can provide an optimized performance. They are popularly
used in GSM/CDMA/UMTS system.
RLK158R10(Z)(R)
Coaxial Radiating Cable, Broadband from 75 –960 MHz, 1-5/8” in,
Low smoke, black non-halogenated or fire retardant polyolefin
jacket.
Type HLHTY(Z)(R)-50-42(1-5/8"D)
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 1-5/8"
Inner Conductor Diameter 17.40 mm | 0.6850"
Dielectric Diameter 42.80 mm | 1.6850"
Outer Conductor Diameter 43.50 mm | 1.7126"
Diameter Over Jacket 48.00 mm | 1.8898"
Inner Conductor Helical Copper Tube
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket
Black PE or Low Smoke Halogen-free Fire-
retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 510 mm
Multiple bending radius 900 mm
Minimum Distance to Wall 50 mm
Tensile Strength 3000 N
Bending Moment 16.0N.m
Flat Plate Crush Strength 1500kg/m
Recommended Hanger Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
30. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 75.0 pF/m
Impedance 50±2 Ω
Velocity 89%
Insulation Resistance >50000 MΩ•km
Jacket Spark 10 KV
Insulation Voltage 15 KV
Inner Conductor DC Resistance 1.50 Ω/km
Outer Conductor DC Resistance 1.50 Ω/km
Stop Band
180~280MHz &
500~580MHz
Operating Frequency Band 75~1000 MHz
VSWR
75~150 MHz ≤1.30
300~500 MHz ≤1.30
600~750 MHz ≤1.30
806~960 MHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation Coupling Loss (2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 001 0,18 63 73
100 0,85 0,26 64 73
150 001 0,27 67 77
350 001 0,43 67 70
450 002 0,49 67 71
650 002 0,61 63 67
800 002 0,73 58 61
900 003 0,79 58 60
960 003 0,88 59 61
31. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic waves
is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in large
complexes like exhibition grounds or airports.
Our coupling series can support all major services from 75 MHz to 3 GHz and is therefore optimally suited for
multi-operator and multi-band applications.
RCF158C24(Z)
Coaxial Radiating Cable, Broadband from 75 –2400 MHz, 1-5/8 in,
Low smoke, black non-halogenated or fire retardant polyolefin
jacket.
Type HLHTY(Z)-50-42(1-5/8")
PHYSICAL DIMENSIONS CONSTRUCTION MATERIALS
Nominal Size 7/8"
Inner Conductor Diameter 17.40 mm |
Dielectric Diameter 42.80 mm |
Outer Conductor Diameter 46.50 mm |
Diameter Over Jacket 49.50 mm |
Inner Conductor Helical Copper Tube
Dielectric Physical Foam Polyethylene
Outer Conductor Overlapping Copper Foil
Jacket Black PE or Low Smoke Halogen-free Fire-retardant
Jacket Color Black
MECHANICAL SPECIFICATIONS
Single Bending radius 510mm
Multiple bending radius 900 mm
Minimum Distance to Wall 50 mm
Tensile Strength 3300 N
Bending Moment 16 N.m
Flat Plate Crush Strength 1200kg/m
Recommended Hanger
Spacing 0.8~1.2m
Fire Retardancy Test Method IEC 60332-1 | IEC 60332-3C-24
Smoke Index Test Method IEC 61034
Toxicity Index Test Method IEC 60754-1 & | IEC 60754-1
ENVIRONMENTAL SPECIFICATION STANDARD CONDITION
Storage Temperature -55 ℃ ~ +85 ℃
Installation Temperature -40 ℃ ~ +80 ℃
Operating Temperature -55 ℃ ~ +85 ℃
Relative Humidity 95%
ROHS YES
As with any radiating cable, the performance in building or tunnel
environments may deviate from figures based on free space method
Due to the cable design, single lengths should not be less than 80m
(262ft)
Attenuation Test Method IEC 61196-4
Attenuation Tolerance ±10%
Attenuation ,Ambient Temperature 20℃ | 68℉
Coupling Loss Test Method IEC 61196-4
Coupling Loss Tolerance ±5dB
Coupling loss values are given with a tolerance of ±5 dB and longitudinal
loss values with a tolerance of ±5%.
32. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
ELECTRICAL SPECIFICATIONS
Capacitance 76.0 pF/m
Impedance 50±2 Ω
Velocity 88%
Insulation Resistance >5000 MΩ•km
Jacket Spark 10 KV
Insulation Voltage 15 KV
Inner Conductor DC Resistance 1.50 Ω/km
Outer Conductor DC Resistance 0.80 Ω/km
Stop Band -
Operating Frequency Band 75~2400 MHz
VSWR
0.3~0.5 GHz ≤1.30
0.8~1.0 GHz ≤1.30
1.7~2.7GHz ≤1.30
ELECTRICAL PERFORMANCE
Frequency Attenuation COUPLING LOSS(2m)
MHz dB/100 m dB/100 ft 50%(dB) 95%(dB)
75 0,6 0,18 68 78
150 0,8 0,24 71 81
450 1,9 0,58 75 85
800 2,6 0,79 75 85
900 2,7 0,82 75 84
1800 4,4 1,34 77 86
2200 5,1 1,55 77 86
2400 5,5 1,68 77 86
Maximum attenuation value shall be 105% of the nominal attenuation value
33. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Radiating Connectors
Radiating cables facilitate radio communication where the usual free space propagation of electromagnetic
waves is hampered, undesired or impossible- in tunnels, mines, buildings, alongside tracks or lines and in
large complexes like exhibition grounds or airports.
The connectors are designed according the standard inter-faces N and 7/16 Type. Contact components are
silver platedto minimize insertion loss, mechanical parts are nickel platedfor heavy-duty handling and best
corrosion resistance.
Radiating Connectors N – 7/16
FEATURES and BENEFITS
• High contact force and Cu-Be inner contacts
• Silver plated
• Watertight (IP67)
• Corrosion resistant
• Quick trimming
• Installation "fit on and tighten it"
MECHANICAL SPECIFICATIONS
CONNECTORS CHARACTERISTICS AND TARGET
structure
Characteristics N Type Din 7/16 Type
Impedance
Operating Voltage Frequency
Range Shielding Effectiveness
Inner Contact Resistance Outer
Contact Resistance
Intermodulation Insulation
Resistance
Dielectric Withstanding Voltage
Insertion Loss
VSWR
0.8 ~ 1.0GHz
1.7 ~ 2.5GHz
Inner Conductor Pin Inner
Conductor Socket Insulator
Body & Outer Conductor
Gasket
Temperature Range
Durability
50 Ω
1500 V
≤18.0 GHz
≥115 dB
≤0.8 mΩ
≤0.25 mΩ
≤-155 dBc
≥5000 MΩ
2500 V
≤0.1 dB
≤1.08
≤1.10
Brass/Silver Plating
Tin Bronze /Silver Plating PTFE or TPX
Brass/Trimetal plating Silicon Rubber
-65 ºC ~ +165ºC
≥500 cycle
50 Ω
2700 V
≤7.5 GHz
≥115 dB
≤0.4 mΩ
≤0.2 mΩ
≤-155 dBc
≥10000 MΩ
3000 V
≤0.08 dB
≤1.08
≤1.10
Brass/Silver Plating
Tin Bronze/Silver Plating PTFE or TPX
Brass/Trimetal Plating Silicon Rubber
-65 ºC ~ +165 ºC
≥500 cycle
34. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
TABLE CONNECTORS SELECTION GUIDE
NF-7/8”L NM-1/2”H DINF-1/2”L DINM-1/2”H
Leaky Radiating CABLE
Cable type leaky 1/2”R leaky 7/8”R leaky 1-1/4”R leaky 1-5/8”R
Connector code
DINM-1/2”R DINM-7/8”R DINM-1-1/4”R DINM-1-5/8”R
DINF-1/2”R DINF-7/8”R DINF-1-1/4”R DINF-1-5/8”R
NM-1/2”R NM-7/8”R NM-1-1/4”R NM-1-5/8”R
NF-1/2”R NF-7/8”R NF-1-1/4”R NF-1-5/8”R
Model Ref. Description
DINM-1/2”R CCF12RDM Connector Radiating DINM-1/2”R std Trimetal plating Straight Male
DINF-1/2”R CCF12RDF Connector Radiating DINF-1/2”R std Trimetal plating Straight Male
NM-1/2”R CCF12RNM Connector Radiating NM-1/2”R std Trimetal plating Straight Male
NF-1/2”R CCF12RNF Connector Radiating NF-1/2”R std Trimetal plating Straight Male
DINM-7/8”R CCF78RDM Connector Radiating DINM-7/8”R std Trimetal plating Straight Male
DINF-7/8”R CCF78RDF Connector Radiating DINF-7/8”Rstd Trimetal plating Straight Male
NM-7/8”R CCF78RNM Connector Radiating NM-7/8”R std Trimetal plating Straight Male
NF-7/8”R CCF78RNF Connector Radiating NF-7/8”R std Trimetal plating Straight Male
DINM-1-1/4”R CCF114RDM Connector Radiating DINM-1-1/4”R std Trimetal plating Straight Male
DINF-1-1/4”R CCF114RDF Connector Radiating DINF-1-1/4”R std Trimetal plating Straight Male
NM-1-1/4”R CCF114RNM Connector Radiating NM-1-1/4”R std Trimetal plating Straight Male
NF-1-1/4”R CCF114RNF Connector Radiating NF-1-1/4”R std Trimetal plating Straight Male
DINM-1-5/8”R CCF158RDM Connector Radiating DINM-1-5/8”R std Trimetal plating Straight Male
DINF-1-5/8”R CCF158RDF Connector Radiating DINF-1-5/8”R std Trimetal plating Straight Male
NM-1-5/8”R CCF158RNM Connector Radiating NM-1-5/8”R std Trimetal plating Straight Male
NF-1-5/8”R CCF158RNF Connector Radiating NF-1-5/8”R std Trimetal plating Straight Male
DIATING COAXIAL CABLE
35. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Radiating Clamp – Premium
Radiating Clamps plastic and metalic systems
System Premium for 1/2", 5/8”, 7/8”, 1-1/4” and 1-5/8”
FEATURES and BENEFITS
• SLX cable clamps are used for the installation of radiating
cables in tunnels.
• SLX clamps may be installed with or without spacers.
• SLX cable clamps are designed with two clips coupled to a
central snap-in cap.
• The two clips allow a quick insertion of the cable, while
the central snap-in cap assures the final locking.
• An additional locking screw is joint.
TECHNICAL FEATURES SPECIFICATIONS
Plastic System Premium
Are used to fasten radiating cables in tunnels, underground and indoor in general.
Additional AISI 302 security screw
PA6V0, black colour, self extinguishing, halogen free (according to UL94 - V0).
Operating temperature : - 40°C + 125°C
Single-hand installation – a matter of course with CLIC, place the cable, apply slight pressure and the clamp locks itself with a sharp clic.
• Automatic locking by pushing cable into clamp
• Unlocks with screwdriver
36. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Radiating Clamp – Premium
TECHNICAL FEATURES SPECIFICATIONS
Metalic System Premium
SLXM - Square Collar for Radiating Cables
Complete with rigid calibrated saddles
The SLXM square collar is formed by two shells joined by
M6 screws and calibrated saddles.
It is recommended in combination with SLXMM clamps for
radiating cables.
Whether inserted at a suitable distance (10-15 m) among
SLX clamps, it prevents radiating cable lines from falling
down, in case of fire.
Material:
Collar: AISI 304 stainless steel
Saddles: Glass reinf. P.A., black colour
SLXCM - Around Collar for Radiating Cables
The SLXCM round collar has been especially designed for quick
installation of HF and DC cables as well as for pipes.
It is recommended in combination with SLX clamps for radiating
cables. Whether inserted at a suitable distance (10-15 m)
among SLX clamps, it prevents radiating cable lines from falling
down, in case of fire.
37. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Radiating Clamp – Premium
TABLE SELECTION GUIDE
Base Plastic Spacer
P.A. Fiberglass Spacer P.A./fiberglass spacer to keep SLXR cable clamps separated from the wall. Fixing with P.A. plug R8/SP.
Material: PA6V0, self-extinguishing, halogen free (according to UL94 - V0).
Code H Description pack gr
SLX2050 50 base spacer 50 mm 50 14
SLX2080 80 base spacer 80 mm 50 22
Plastic System
Code Model Cables For cables øD L H h1 gr
SLX0012 SLXR 1/2’’ 15-18 46 36,5 13 20
SLX0058 SLXR 5/8” 20-23 46 41 13 22
SLX0078 SLXR 7/8” 26-30 46 45 13 26
SLX0114 SLXR 1.1/4” 38-41 66 65 17 68
SLX0158 SLXR 1.5/8” 47-51 81,5 80 19 116
Metalic System
Code Article/description ØD L H pz gr
SLX0012M Clamp Metalic System Premium 1/2’’ 16 - 17 16 - 17 22 36 50 90
SLX0058M Clamp Metalic System Premium 5/8” 21 - 23 21 - 23 22 36 50 86
SLX0078M Clamp Metalic System Premium 7/8” 27 - 28 27 - 28 34 48 50 114
SLX0114M Clamp Metalic System Premium 1.1/4” 39 - 40 39 - 40 34 48 50 110
SLX0158M Clamp Metalic System Premium 1.5/8” 50 - 52 50 - 52 34 48 50 108
Code Article Cables ØD H pz
SLXCM0020 Clamp Metalic System Premium 1/2’’ Ø 13 ÷ 20 1/2” Ø 13 ÷ 20 44 20
SLXCM0030 Clamp Metalic System Premium 7/8” Ø 22 ÷ 30 7/8” Ø 22 ÷ 30 55 20
SLXCM0040 Clamp Metalic System Premium 1.1/4” Ø 30 ÷ 40 1.1/4” Ø 30 ÷ 40 67 20
SLXCM0050 Clamp Metalic System Premium 1.5/8” Ø 40 ÷ 52 1.5/8” Ø 40 ÷ 52 79 20
Code L Description pack
SLX1050
50 Spacers with M8x16 screw and washer RPI 8/16 50
SLX1075 75 Spacers with M8x16 screw and washer RPI 8/16 50
SLX1010 100 Spacers with M8x16 screw and washer RPI 8/16 50
38. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Radiating Clamp – Premium
EXAMPLES OF INSTALLATION
Base Plastic Spacer
SLX Installation example
Installation of Radiating Cable in Tunnel
Installation by using SLX cable clamps.
SLX cable clamps are fixed to the wall by a mechanical
or chemical fastener, directly or through spacers
The installation is quick and safe thanks to an elastic
provisional pre-fixing of the cable. The final closure
is assured by the cap of the SLX cable clamp
SLX Installation example
Installation of Radiating Cable on Cable Trail Fixing of SLX clamp on linear guide rails
with spacers SLX10 or SLX24
39. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Radiating Clamp – Standard
Radiating Clamp System
Clic clamps are used for installing radiating cables in gal- leries and tunnels with or without spacers. The
installation is very simple and quick.
Stainless Stell Cable Clamps are used to provide Fire Resistant installations of Radiating Cables in galleries or
tunnels with or without spacers.
The installation is very simple and quick. To limit the interference that could be caused by Metal Objects on the
RF field generated by a Radiating Cable, only every 10th fixing should be metallic.
Radiating Clamps plastic and metalic systems
1/2" | 5/8” | 7/8” | 1-1/4” | 1-5/8”
FEATURES and BENEFITS
• Lock with 1 or 2 locking positions
• Automatic locking by pushing cable into clamp, reusable
• Unlocks with screwdriver
• Pivoted hangers allow installation down to -25°C
• Slot design allows installation correction of up to 4.5 mm
• Slot for insertion of flange for rod and stud mounting
TECHNICAL FEATURES SPECIFICATIONS
Plastic System
Material Pure Polyamide, halogen free, fire class UL94HB, UV-resistant
Environmental
Operating Temperature °C - 25 to +110
Installation Temperature °C -10 to +60
Color standard black
Metalic System
Material Metalic Clamp Fire Resistant
Environmental
Operating Temperature °C - 50 to +400
Color standard black and metalic
40. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Radiating Clamp – Standard
TABLE SELECTION GUIDE
Plastic System
Clic type for 1/2” for 5/8” for 7/8” for 1-1/4” for 1-5/8”
Clamping mm 14.3 - 16.8 19.5 - 22.0 24.6 - 27.8 35.5 - 39.5 46.5 - 50.5
Max. load N 600 700 850 1100 1300
Part reference SLX9415AN SLX9420AN SLX9426AN SLX9435AN SLX946AN
Metalic System
Clic type for 1/2” for 5/8” for 7/8” for 1-1/4” for 1-5/8”
Clamping mm 15 22 27 38 49
Max. load N 600 700 850 1100 1300
Part reference SLX9XCLIP15 SLX9XCLIP22 SLX9XCLIP27 SLX9XCLIP35 SLX9XCLIP46
SPACERS and ACCESSORIES
Click Calmp
Reference Description
SLX94CSCRM Round base spacer 80 mm
SLX94CSCQM Round base spacer 80 mm
SLX9X481207981 Wood screw 4.8 x 120mm
SLX9X895912 DIN 912 M8x95mm, hex socket head
SLX96FX Nylon plug for wood screw diameter 6 mm
SLX9X8SFA Stainless steel plug M8
41. Silex Global Spain, S.L. | All specifications are subject to change. techsupport@silexst.com - www.silexst.com
Silexst reserves the right to make such changes as required. Unless otherwise stated, all specifications are nominal. © 2015 Silexst Todos los derechos reservados
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements.
See www.silexst.com for the most current information. Revised: September 09, 2014. www.silexst.com
RADIATING COAXIAL CABLE
Leaky Cable
Regulatory Compliance/Certifications
ISO 9001:2008
ISO 14001:2004
OHSAS 18001
RoHS 2011/65/EU RoHS Compliant
Designed, manufactured and/or distributed under quality
management system
Silexstr Radiating Cable ® functions as a distributed antenna to
provide communications in tunnels, mines and large building
complexes and is the solution for any application in confined areas.
Slots in the copper outer conductor allow a controlled portion of the
internal RF energy to be radiated into the surrounding environment.
Coupling & Radiating Cable is used for both one-way and two-way
communication systems and because of its broadband capability, a
single radiating cable can handle multiple communication systems
simultaneously.
42. Radiating and Coupling Cable Systems
Frequency
TETRA / TETRAPOL
TDMA / CDMA 800
GSM 900
DCS / GSM 1800
PCN / PCS 1900
UMTS 2200
W-CDMA 2200
DECT 900
GSM-R
WLAN 2400
WLAN 5700
LTE
Cables
Together the cables and the connectors from
Silex are an unbeatable match that optimises the
entire system performance:
• Low attenuation
• Excellent field strength with low coupling
loss
• Increased amplifier spacing due to very low
longitudinal attenuation
• Simple connector installation
• Quick cable installation
• Halogen-free and fire retardant jacketing
43. .
Silex Global Spain, S.L.
San Erasmo, 31 Nave 8
28021 - Madrid (Spain)
Tel.: + 34 915 05 67 76
E-Mail: info@silexst.com
Web: www.silexst.com
Web: www.silexfiber.com
Certified Products: ISO / EN / IEC
Ordering No.
Info32543SLink/WERE/09-2014
pA 1SFSD34
© 09.2015 Silexst
Production & Powered By Silex Global Spain
All specifications are subject to change. See www.silexst.com for the most current information. Revised: September 06, 2015
Silex Global Spain, S.L. | The information contained in this document is accurate to the best of our knowledge and representative of the part
described herein.
It may be necessary to make modifications to the part and/or the documentation of the part, in order to implement improvements. Silexst reserves the right to
make such changes as required. Unless otherwise stated, all specifications are nominal.
info@silexst.com – www.silexst.com
©2014 Silexst All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of Silexst