Bts commissioning (alcatel lucent)

2. Switch OFF the
BTS cabinet and
disconnect Abis
connectors from
DDF before offline
start

3. Disconnect
the Abis
connector
from The DDF

4. Switch ON the
BTS cabinet
breakers and
connect the
Laptop with
BTS

5. User Name
“COMMTE”
Password
“COMMTE”

6. Communication
Port setting

7. OR

8. After
connecting
this window
will be appear

9. Go to
Configuration->
BTS-SW
Download->
to download
BTS software

10. After BTS-
SW
download
this window
will appear

11. Go to offline
Files and select
First File of
Master File.

12. Go to offline
Files and select
First File of
DDL file.

13. Click ok to
start
downloading
SW

14. BTS software
starts to
download.

15. All these
Files are
downloaded

16. Go to
Configuration
BTS
commissioning

17. Click start
commissioning

18. Edit Qmux
Address

19. Edit sector
Mapping

20. Check All
Twin TRE’s.

21. Click End
Commissioning
Click << arrow
to move selected
modules to
available
modules

22. All modules
Shifted to
update
modules.

23. Click No to
end

24. Reconnect the
Abis connector at
DDF by verifying
the TX/RX cables
properly

25. Give Hard Reset to
BTS cabinet as the
OML has established
to put the site on
Downloading.

26. OFF Line Commissioning
Completed
Successfully.

27. BTS ON-Line commissioning
Procedure using B10
Go to
configuration>>
Hardware
setting>>Begin
HW modification

28. Go to
configuration>
BTS
commissioning
Go to start
commissioning>
Edit Q1
Address, Edit Sector
Mapping and Twin
TRA setting as in
offline.

29. Go to
configuration>
Hardware
setting>“End
Modification” to
end online
commissioning

30. Online commissioning steps
 Connect the Abis connector at DDF by verifying Tx/Rx
cable properly.
 OML will be established after primary Abis has
connected to DDF.
 Give hard reset to BTS after OML has established.
 Put site on Downloading from OMC.
 O&M will be established as downloading completes.
 Connect Laptop to BTS MMI port.
 Go to configuration>Hardware setting>Begin Hardware
modification.

31. Online commissioning steps
 Go to configuration>BTS commissioning>start
commissioning.
 Edit Qmux Address
 Edit sector mapping
 Check all Twin TRA setting.
 Click end commissioning and shift all modules from selected
modules to available modules.
 Go to configuration>Hardware setting>End Hardware
modification.
 Click “yes” when an automatically hardware modification
window appears.
 Hw Audit will be run and all Hardware will be shown after
sometime.

32. ON Line Commissioning
Completed
Successfully.

33. Software components
combiner Fan Unit
Hardware
Shown in
software
window
Tre’s
clock
Alarm
card

34. Alarms
window

35. Transceivers
Shown in
window

36. Transceivers Types
 Four type of Transceivers in Alcatel Equipment
 TRAGE>Gsm Single TRE
 TRADE>Dcs single TRE
 TGT09>Gsm Twin TRE
 TGT18>DCS Twin TRE
 TAGHE>High power TRE

37. VSWR
Shown in
window

38. Sectors
Shown
In window

39. Station units

40. BSC SBLs
(security block levels)
BTS OM & Sectors.Sec
RSLs can be unlock
from local Terminal.

41. Troubleshooting
 If a TRE or combiner is in “Not Operational” or “FOS” state then
disable it then initialize it by using “init” command.
 If TRE or combiner can not operational by doing above command
then remove it by using the following method.
 Go to configuration>>Hardware setting>>Begin HW modification.
 Go to Configuration>>Hardware setting>>Remove.
 Remove the Hardware from BTS.
 Window will be appear of Hardware removal, select the module to
remove.
 Go to Configuration>>Hardware setting>>End Modification.
 Click ”yes” when configuration changes window appears.

42. Hardware
Removal
Method
Step:1

43. Hardware
Removal
Step:2

44. Hardware
Removal
Step:3

45. Troubleshooting cont..
 When a module goes in “FOS” state then it must be disable by
using ”disable” command before initializing it by using “init”
command otherwise it will not goes to operational state.
 When a module is in “Not Operational” state with color white
then it means it has not got it’s RSL number still. Reload BTS
data by going to “configuration>Reload Bts data” or using a
method of “Begin Hardware then End Hardware” as discussed
earlier. It will take some time to become operational.
 When a module is in “MSD” or “MSA” state then it will not get
any command because its maintenance has seized for a while.
 When TRE RSL has locked then then its RSL will not be
stable, so unlock the TRE from OMC.

46. Troubleshooting cont..
 Sometime there is some faulty hardware in Bts that’s why other
sectors or TRE’s can effect and can not work properly. Due to
these faulty hardware other sectors or TRE’s can be down so
simply remove this hardware. By this method other hardware
become in operational state.
 Some time “SUMA” can not work properly that’s why whole Bts
effects so change the slot of “SUMA” and give hard reset to Bts.
 If modules in a shelf can not powers up then check it’s power
cable at the back ports of Bts or check it “RI” cable. Also check
the power switch for the concern shelf.
 If a “EACB” card is Not operational or “FIT” state then initialize it
from software. If it again goes in “FIT” state then Alarm card is
faulty.

47. Troubleshooting cont..
 Some time Primary Abis is stable by showing LED on Suma card
but OML can not become stable, It means that Abis LED is fake.
So check the Tx/Rx cable from both Bts end and microwave end
and make sure that it is correctly connected. Also check Tx/Rx
patching on DDF by using LED. Make sure that LED blinks on
every pair on DDF. Also check the BNC and Abis connectors.
Abis cable which is connected from Suma card to Bts board can
be faulty so also verify it.
 If a TRE or combiner can not operational than change its slot
then verify it.
 Vswr issues can be resolved by checking connectors from Bts end
and feeder end.
 The last option for Alcatel equipment to become operational is
the “Hard reset of Bts”.

48. External Alarms of MBO2

49. ALCATEL GLOSSARY
A
AN Antenna Network
B
BCB BTS Control Bus
BSII Base Station Controller
BSS Base Station Subsystem
BTS Base Station Transceiver
BTSW BTS-Terminal for Windows
C
CCF Cabinet Cooling Fan
CDM Configuration Data Message
CLEI Common Language Equipment
CLLK Clock Link
CPF Configuration Parameter File
CRC Cyclic Redundancy Check
CU Carrier Unit

50. ALCATEL GLOSSARY
D
DC Direct Current
DMA Deferred Maintenance Alarm
E
EQU Equipped
F
FIA Format Identifier for Application part of RI
FIM Format Identifier Manufacturing
FIT Faulty In Traffic
FLT Faulty
FOS Faulty Out of Service
ICS Item Change Status
IT In Traffic
L
LDA Local Defence Action
LRA Local Recovery Action
M
MI Maintenance Information
MSA MSD Auto
MSD Maintenance Seized

51. ALCATEL GLOSSARY
N
NEQ Not Equipped
NOP Not Operational
O
O&M Operation and Maintenance
OMU Operation and Maintenance Unit
OMUA OMU A RIT
OMUB OMU B RIT
OP Operational
OPR Operator
P
PADD Physical Address
PMA Prompt Maintenance

52. ALCATEL GLOSSARY
R
RA Radio Access
RF Radio Frequency
RFH Radio Frequency Hopping ( also known as : Synthesizer
Hopping )
RI Remote Inventory
RIT Replaceable Item
RX Receiver or receive .....
RTC Remote Tunable Combiner
S
SBL Security Block Level
SCFE Station Unit Control Function Entity RIT
SOS System Out of Service
SUM Station Unit Module
SUMP SUM PCM RIT
SW Software

53. ALCATEL GLOSSARY
S
SBL Security Block Level
SCFE Station Unit Control Function Entity RIT
SOS System Out of Service
SUM Station Unit Module
SUMP SUM PCM RIT
SW Software
T
TLV Tag, Length, Value
TRE Transceiver Module (combined Transmitter / Receiver
functionality for base band and RF signals)
TS Timeslot
TX Transmitter or transmit .
V
VPMA Very Prompt Maintenance Alarm
VSWR Voltage Standing Wave Ratio

54. ALCATEL GLOSSARY
W
WBC Wide Band Combiner
WTC Wait Traffic Clear
X
XBCB External BCB
XCLK External Clock
XIOB External Input Output Board