This is an ideal sized compact digital level that also incorporates the bubble. At 8 inches with 0.1 Degree Resolution. It's LCD display is easy to read with measurements in either degrees and percentages. 1 horizontal and 1 vertical vial. Buzzer Sound at 0, 90 and when you hold a reading Hold Function to freeze display on current reading Long Battery Life with 3 minutes auto off. Built in strong magnet base to firmly hold on flat and pipe surfaces
High accuracy of 0.1 degrees at 0° and 90° and 0.2 degrees at all other angles
Switchable display between degrees (°) or slope (%)
Strong magnet on the base enable the level to be fixed on to any magnetic surface
Buzzer sound at 0°
Measurement Range 0° ~ +/- 90° x 4 (360°)
Beginners Guide to TikTok for Search - Rachel Pearson - We are Tilt __ Bright...
Model dwl 200 series digital torpedo level- www.DIGIPAS.co.uk
1. Model DWL 200 Series
The DWL 200 is a 200 mm length Digital Mini Level. The strong impact resistance ABS
plastic material is molded with a tough Aluminium base to form the rugged yet elegant
body structure.
Features & Specification:
Models Special Feature
Displayed in Degrees (° or slope (%)
)
DWL 200 Resolution 0.1°
• Measurement Range 0° ~ +/- 90°
High Resolution 0.05°~ 0.1° DWL 280 Resolution 0.05°~ 0.1°
• Operating Temperature 0° ~ 50° C Dimension L(200) x H(42.5) x T(18) mm
• Long Battery Life with 3 minutes auto off
• Easy, Clear & Precise Digital Display
• Hold Function to Freeze Display
• Buzzer Sound
with Build-in Vials
With magnet on the base
Power supply 2 x 3v Lithium cell
(Batteries included)
For further information, please refer to www.digipas.co.uk
2. CALIBRATION INSTRUCTION
Caution: Digi-Pas is calibrated in the Factory for OPERATION
maximum accuracy. User only recalibrate unless a) Batteries:
necessary. Open the battery compartment at the
rare of the Digi-Pas .
1. Push ONCE on the Cal button then Remove the small plastic from two new
release.Buzzer starts to beep. batteries (type AAA/LR03).
2a. Place Digi-Pas on a flat surface (e.g. Table) Ensure correct polarity.
Use a finger to Press Mode button ONCE while b) Switching on the Digi-Pas:
wait a few seconds until buzzer beeps. Switch the Digi-Pas on using the on/off
b. Place Digi-Pas reverse horizontal (180° Press
) switch.
Mode button ONCE and wait a few seconds until The Digi-Pas can measure angles range
buzzer beeps. 0°~ +/- 90°
c. Place Digi-Pas vertically (-90° and Press
) press mode button to choose the
Mode button ONCE and wait a few seconds until resolution in degree or slope angle (If
buzzer beeps. slopes are measured)
d. Place Digi-Pas reverse vertically (+90° and
) c) Buzzer Sound (Acoustic signal):
Press Mode button ONCE and wait a few seconds The Buzzer Sound are used to indicated
until buzzer beeps. angle of slope stands at 0° 45° 90°
, , .
3. Calibration completes when buzzer beep To switch off Acoustic signal, hold the
sound stops. Mode for more than 2 seconds, the
NOTE : Ensure Digi-pas is kept still during speaker enunciator will be disappeared.
Calibration
d) Magnets on the based
The Digi-Pas can be affixed to any
magnetic surface.
e) Hold button (Memory functions)
With the hold button, you can Freeze
Display for reading and the current
measurement result can be saved in the
internal memory.
Return to normal measuring mode by
pressing Hold button
To call back the reading in the internal
memory, press Hold button for 3 second.
The previous save reading will be
appearing in the display.
f) Switching off:
To switch off the Digi-Pas, press the
on/off switch .When not in use more
than 3 min, the Digi-Pas will switches off
automatically.
UK and Europe sales office
Tarax Technology Limited
First Floor, Office 2,
10 Panmure Street,
Dundee,
DD1 2BW.
e:Info@digipas.co.uk
w:www.digipas.co.uk
m:(+44)07825041403
For further information, please refer to www.digipas.co.uk