Mobi360 user guide

einstruction.com/products/mobile-interactive-whiteboards
User Guide

Mobi 360™ 2
© 2013 Turning Technologies, LLC. Portions Responsive Innovations, LLC, Microsoft Corporation
No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose,
without the express written permission of Turning Technologies, LLC. All rights reserved.
Turning Technologies, LLC, 255 West Federal Street, Youngstown, OH 44503 USA.
TurningPoint® is a registered trademark of Turning Technologies, LLC. Other trademarked product names mentioned in this manual
are owned by their respective companies.
The following regulatory statements apply to radio frequency and infrared transmitters and receivers mentioned in this manual,
including the ResponseCard RF, ResponseCard RF LCD, ResponseCard IR, ResponseCard XR, ResponseCard NXT and their
respective receivers.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Mobi 360™ 3
ABOUT MOBI 360™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Technical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mobi 360 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pairing the Mobi 360 with the Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Calibrating the Mobi 360 Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Changing the Language on the Mobi 360. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Adjusting the Brightness on the Mobi 360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Calibrating the DualBoard™ with Mobi 360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Updating Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mobi 360 Zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mobi 360 Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Starting a Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Starting a Class on Mobi 360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Changing a Class on Mobi 360. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Starting an Anonymous Session. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Accessing Favorites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Replacing and Charging the Mobi 360 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Charging the Mobi 360 Pen Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Replacing the Mobi 360 Pen Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LESSON ZONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Display Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Displaying the Computer Screen from the Mobi 360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Displaying Whiteboard Mode from the Mobi 360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using the Curtain to Hide the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
The Digital Pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using the Pen as a Mouse Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using the Pen as a Pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using the Pen as a Highlighter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Using the Pen to Draw Shapes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Using the Pen to Draw Straight Lines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Using the Pen as an Eraser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Using the Pen as a Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Multi-User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Entering Multi-User Mode on the Mobi 360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Locking or Hiding the Screen in Multi-User Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Exiting Multi-User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Annotating the Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Annotation Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Hiding Annotations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Deleting Annotations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Note on Mobi 360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Note Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Creating and Displaying a New Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Using the Mouse Pointer in Note View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Using the Eraser in Note View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Displaying a Previous Note. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Deleting a Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Screenshots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Mobi 360™ 4
Saving Screenshots with the Mobi 360. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Displaying Screenshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Using the Screenshot Sorter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Annotating Screenshots with the Mobi 360. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Accessing Screenshots from Insight 360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
QUESTION ZONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Asking Verbal Questions During Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Asking Tagged Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Asking ExamView Questions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Timing Student Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Initial Question Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Displaying the Student Response Grid on-Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Displaying Question Results on-screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
RESULTS ZONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Results Zone Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Viewing Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Ending a Class Session. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
CONTACT US . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Office Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Mobi 360™ 5
ABOUT MOBI 360™
Mobi 360 is the mobile interactive whiteboard used to display coursework, annotate your computer desktop, and pose
interactive questions.
The Mobi 360 comes with a receiver, USB cable, charging stand and digital pen.
Through the Mobi 360, you can:
• Navigate and control the classroom computer desktop
• Access Favorites
• Ask Verbal and Tagged questions
• Interact with any software installed on your classroom computer by using the Mobi 360 as your keyboard and mouse
This chapter covers the following topics:
NOTE
The digital pen does not contain any ink and cannot be used to write on
paper or surfaces other than the Mobi 360.
• Technical Requirements
• Mobi 360 Setup
• Mobi 360 Zones
• Mobi 360 Icons
• Starting a Class
• Care and Maintenance

Mobi 360™ 6
Technical Requirements
The only requirement for the Mobi 360 is that the connected computer has the Insight 360 software installed and
running.
Mobi 360 Setup
The Mobi 360 and digital pen are delivered partially charged to allow you to use these items immediately after unpacking
the box. However, it is recommended to charge these items for approximately eight hours before beginning normal use.
This section covers the following topics:
PAIRING THE MOBI 360 WITH THE RECEIVER
The Mobi 360 connects with the Insight 360 software through the wireless Mobi 360 receiver. The receiver is a USB
device stored in the charging stand or on the backside of the Mobi 360.
The Mobi 360 is paired with its Mobi 360 receiver at the factory. This pairing is confirmed the first time the Mobi 360 is
turned on. The first time the Mobi 360 is turned on, it attempts to connect automatically with its receiver. If Mobi 360
cannot connect to its receiver, you can manually pair the device.
How to pair the Mobi 360 with the receiver...
1 Turn on the classroom computer on which the Insight 360 software is installed.
2 Insert the Mobi 360 receiver into a USB port.
3 Turn on the Mobi 360 by pressing the blue power button on the top of the unit.
The message Please wait while a connection to Insight 360 is being established is displayed on the Mobi 360 screen.
4 When the message, Ensure the Mobi 360 Receiver is displayed, confirm the Mobi 360 receiver has been inserted into
a working USB port.
5 Press and release the blue button on the Mobi 360 receiver while the receiver is still inserted into the USB port on the
computer.
6 Tap Continue on the Mobi 360.
The message Please wait while a connection to Insight is being established shows on the Mobi 360 screen. When the
Mobi 360pairs with its receiver, the Teach Class screen is displayed on the Mobi 360.
• Pairing the Mobi 360 with the Receiver
• Calibrating the Mobi 360 Touchscreen
• Changing the Language on the Mobi 360
• Adjusting the Brightness on the Mobi 360
• Calibrating the DualBoard™ with Mobi 360
• Updating Firmware
NOTE
You can check the connection status of both devices from Device
Management in My Settings on the Insight 360 software.
NOTE
If a USB hub is needed, ensure that a powered USB hub is used.

Mobi 360™ 7
How to pair the Mobi 360 with the receiver manually...
1 You can pair the Mobi 360 with its receiver manually if they do not pair automatically or if the Mobi 360 receiver has
been replaced with a new one. Turn on the classroom computer on which the Insight 360 software is installed.
2 Insert the Mobi 360 receiver into a USB port on the classroom computer.
3 Turn on the Mobi 360 by pressing the blue power button on the top of the unit.
The message Please wait while a connection to Insight is being established is displayed on the Mobi 360 screen.
4 When the message, Mobi is unable to connect is displayed, tap Settings.
5 Tap Pair with Hub.
6 Press the blue button on the Mobi 360 receiver while the receiver is still inserted into the USB port on your computer.
7 Tap Continue on the Mobi 360.
The message Please wait while a connection to Insight is being established shows is displayed on the Mobi 360
screen.
8 When Mobi 360 connects to its receiver, the Mobi 360 Home screen is displayed.
CALIBRATING THE MOBI 360 TOUCHSCREEN
The touchscreen occasionally requires calibration. Recalibrating ensures that the Mobi 360 recognizes digital pen taps
in the same place that you are actually tapping, writing or drawing on the touchscreen.
How to calibrate the Mobi 360 touchscreen...
1 From the Mobi 360 Home screen, tap Settings.
2 Tap Calibrate Touchscreen.
3 Follow the on-screen directions to tap each dot as it appears.
4 Tap OK.
CHANGING THE LANGUAGE ON THE MOBI 360
You can change the language on the Mobi 360 through Settings.
NOTE
Use the digital pen for better accuracy during the calibration process.
IMPORTANT
Changing the language on the Mobi 360 will also change the language on
connected clickers.

Mobi 360™ 8
How to change the language on the Mobi 360...
2 Tap Language.
3 Tap the language to which you want to set the Mobi 360 (and connected clickers).
ADJUSTING THE BRIGHTNESS ON THE MOBI 360
Adjusting the amount of brightness will affect battery life; brighter screens take more battery. The Mobi 360 touch screen
dims after a set amount of time to maximize battery life. You can adjust both the default screen brightness and the
amount of time the screen can sit without being used before it dims.
How to adjust the brightness on the Mobi 360...
2 Use the digital pen to tap and hold the vertical line in the Brightness slider.
3 With the pen tip on the vertical line, slide the vertical line:
• Slide to the right to brighten the screen.
• Slide to the left to darken the screen.
4 Remove the pen tip from the slider.
5 Optionally, in the Dim screen after section:
• Tap Plus to add more time before the screen dims.
• Tap Minus to subtract time before the screen dims.
CALIBRATING THE DUALBOARD™ WITH MOBI 360
If you have a DualBoard connected to your Mobi 360, you may need to periodically calibrate the DualBoard. This
ensures that any writing or drawing on the Mobi 360 is accurately reflected.
How to calibrate the DualBoard with Mobi 360...
1 From the Mobi 360 Home screen, tap My Settings.
2 Tap Calibrate DualBoard.
NOTE
By default, the Skip this screen at startup checkbox is selected. Uncheck
this box if you will frequently select different languages at startup (such as
if you are a language instructor).
NOTE
If the screen dims while you are teaching, tap the screen with the digital
pen or your fingertip.

Mobi 360™ 9
3 Follow the on-screen directions to tap each dot as it appears.
4 Tap OK.
UPDATING FIRMWARE
Turning Technologies periodically updates the firmware on the Mobi 360, the Mobi 360 receiver and student devices. If
Insight 360 detects a new version of the firmware for the Mobi 360, Mobi 360 receiver or handset receiver, it generates a
message at startup on the Mobi 360. Insight 360 also generates a message in the Message Center and places an icon
next to the firmware version requiring update in Device Management in My Settings. You can begin the firmware update
process by clicking the link displayed in the Insight 360 Message Center.
How to update firmware...
1 The One or more of your devices has a firmware update available message is displayed in the Message Center when
you start the Mobi 360.
2 If updating the Mobi 360 firmware, remove the Mobi 360 receiver from the classroom computer running Insight 360.
3 Connect the device (Mobi 360, Mobi 360 receiver or handset receiver) requiring the firmware update to the computer
running the Insight 360 software via USB or USB cable.
4 Open Insight 360.
The Insight 360 Message Center displays an Update message informing you that a firmware update is available for
the Mobi 360.
5 Click the underlined Update link in the Insight 360 message.
A message box opens to inform you that you are about to update your device and asks if you want to continue.
6 Click Yes.
7 When the update is complete, the Firmware Update dialog box appears. Click OK.
NOTE
Use the digital pen for better accuracy during the calibration process.
NOTE
Do NOT attempt to update the Mobi 360 using the charging stand.
Information will not flow from the charging stand to the Mobi 360. Use the
USB cable provided to connect the Mobi 360 directly to your computer.
NOTE
During the firmware update process, do NOT turn off or disconnect the
Mobi 360 receiver or the Mobi 360 USB cable.

Mobi 360™ 10
Mobi 360 Zones
Mobi 360 organizes its functions into the following zones:
Mobi 360 Icons
Several icons reside in the upper right corner of the Mobi 360 screen. These informational icons remain in this area
(when applicable) regardless of the screen or zone currently showing.
The Lesson Zone provides annotation and screen display tools used during instruction.
The Question Zone provides tools necessary to ask Verbal, Tagged and ExamView questions and
receive responses through student response systems.
The Results Zone displays results of the most recently asked question in various formats and provides
summary information about the current session.
The Favorites Zone opens previously configured course materials on the desktop computer.
The Class Zone allows you to end class.
More provides access to Settings and Help.
Additional Mobi family device (plus one digit indicating the quantity of devices joined)
Student response pad joined (plus three digits indicating the quantity of student response pads joined)
Pulse/Spark 360 receiver disabled (probably not connected)
Mobi 360 receiver enabled
Mobi 360 connected to computer via USB cable
Pen charging
Pen detected (shows when pen tip is near Mobi 360 writing surface)
This icon turns red when the pen battery needs to be recharged.
Mobi 360 battery charging
Mobi 360 battery level

Mobi 360™ 11
Starting a Class
When you tap Teach Class on the Mobi 360, the device initially displays information for the class configured in Insight
360 to take place during the current date and time.
• Starting a Class on Mobi 360
• Changing a Class on Mobi 360
• Starting an Anonymous Session
• Accessing Favorites
STARTING A CLASS ON MOBI 360
When a class session is started, the Mobi 360 communicates with the Insight 360 software to:
• Open the student roster for that class
• Recognize the student response clickers by their student or sticker IDs (depending on setup configuration)
• Match the student response systems with the students during the class session
How to start a class on Mobi 360...
1 Tap Teach Class.
Confirm the class name, time and period number correct.
2 Tap Start Class.
CHANGING A CLASS ON MOBI 360
When you tap Teach Class on the Mobi 360, the class that is normally scheduled for the current date and time appears.
If this is not the class you want to start, you can change to a different class.
How to change a class on Mobi 360...
1 Tap Teach Class.
The currently scheduled class name, time and period is displayed.
NOTE
If this is not the class you want to start, tap Change Class. If no classes
are listed, tap Find Class. Select the desired class.
NOTE
Change Class works only if you have not already started the class. If you
have already started a class and want to change, you must end the class
first.

Mobi 360™ 12
2 Tap Change Class.
3 Tap the class you want to start.
Tap down to view more classes.
4 Tap Start Class.
STARTING AN ANONYMOUS SESSION
An anonymous class session can be used when you want to start an impromptu session or when a class has not been
pre-configured in Insight 360.
During an anonymous class:
• Student devices are not associated with specific students
• Student responses remain anonymous
• Insight 360 will save data for an anonymous class session, but the data will not be associated with individual students.
You can associate the data to a class after the session ends.
How to start an anonymous session...
1 From the Mobi 360 Home Screen, tap Teach Class.
2 Tap Anonymous.
3 Tap Start Class.
ACCESSING FAVORITES
The information stored on the My Favorites tab in Insight 360 can be accessed directly from the Mobi 360.
How to access favorites...
1 Tap Favorites.
2 Tap the item to display.
3 To access Favorites on other pages, tap the up or down arrows.

Mobi 360™ 13
Care and Maintenance
The Insight 360 system components are easy to maintain.
• Store the Mobi 360, charging stand, digital pen, and student devices in a clean, dry place
• Clean with a dry or lightly damp cloth
• Periodically charge the battery on the Mobi 360 and its digital pen
• Replace the batteries in the Mobi 360 and digital pen as needed
• Replacing and Charging the Mobi 360 Battery
• Charging the Mobi 360 Pen Battery
• Replacing the Mobi 360 Pen Battery
REPLACING AND CHARGING THE MOBI 360 BATTERY
The Mobi 360 contains a rechargeable battery pack that can last for several days, with normal use, before requiring
charging.
• The Mobi 360 is delivered with a partial charge to allow you to start using it directly after unpacking the system
• The battery must be charged periodically to ensure the Mobi 360 is available for use when you need it
• Allow eight hours to fully charge the Mobi 360 battery
• The digital pen is charged from the Mobi 360 battery when the pen is fully seated in its Mobi 360 holder
• When not being used, the Mobi 360 should remain on its charging stand to ensure it receives a full charge
• The charging stand must be plugged into an electrical outlet using the standard electrical plug for your country
How to replace and charge the Mobi 360 battery...
1 Use a Phillips screwdriver to loosen screws on battery compartment cover, located on back of Mobi 360 and remove
the battery cover.
2 Remove and disconnect the existing battery pack.
NOTE
DO NOT SUBMERGE the Mobi 360, digital pen or student devices.
IMPORTANT
Do NOT attempt to charge the Mobi 360 by plugging the charging stand
into a computer's USB port. When using the charging stand, insert the
USB end of the charging stand cable into the electrical plug appropriate for
your country, and then connect the electrical plug into an electrical outlet.

Mobi 360™ 14
3 Connect the new battery pack.
4 Gently insert the new battery pack into the compartment.
5 Replace the battery cover and tighten the screws.
6 Charge the Mobi 360 battery for eight hours. Place the Mobi 360 on the charging stand plugged into an electrical
outlet.
CHARGING THE MOBI 360 PEN BATTERY
The Mobi 360 digital pen is delivered with a partial charge to allow you to start using it directly after unpacking the
system.
• The digital pen charges whenever it is securely placed in its holder in the back of the Mobi 360
• Store the pen in its holder when the pen is not in use
• When the digital pen is in its holder on the Mobi 360, the pen charging icon appears
You may also see other icons associated with the pen:
How to charging the Mobi 360 pen battery...
1 Insert the pen into the pen holder at the top of the Mobi 360.
2 Press the pen firmly into the holder to ensure a good connection with the recharger.
3 Store the pen in the pen holder when the pen is not in use.
4 Allow eight hours for the pen battery to fully charge.
IMPORTANT
Avoid pinching the wires as you replace the battery cover.
A charging icon appears when the Mobi 360 is charging
Pen detected (appears when pen tip is near the Mobi 360 writing surface)
Pen battery low (needs charging)
NOTE
To conserve battery life, the pen goes into “sleep” mode after two minutes
of inactivity. Click the rocker button or touch the tip to reactivate the pen.

Mobi 360™ 15
REPLACING THE MOBI 360 PEN BATTERY
The pen uses a AAAA rechargeable battery that typically lasts more than a year with normal use. Replace the battery
when the Mobi 360 digital pen battery will no longer hold a charge.
How to replace the Mobi 360 pen battery...
1 Gently press the tab and slide the two sections of the pen apart.
2 Remove the old battery.
3 Insert a new AAAA rechargeable battery with the positive terminal (+) facing toward the tip of the pen.
4 Press the pen tip.
The LED located at the pen tip will flash four times if the battery was inserted correctly.
If the LED does not flash four times, remove the battery, check that the battery's positive (+) end is facing toward the
tip of the pen, and re-insert the battery.
5 Align the ridges of the pen's back section with the slots of the pen's front section and slide the two sections together
until the tab re-engages.
6 Charge the pen battery for eight hours.
TIP
To extend the life of the battery, remove the battery from the pen when the
pen will not be used for an extended period of time (for example, during
summer holiday).

Mobi 360™ 16
LESSON ZONE
Most of your instruction time will be spent in the Lesson Zone. At the bottom of the Mobi 360 screen, tap Lesson.
The Lesson Zone contains the following:
• Display options
• Annotation tools
• Note and Curtain tools
• Multi-user functions
• Keyboard functions
• Sorter tool
• Undo/Redo/Hide and Delete buttons
• Screenshot tools
This chapter contains the following sections:
• Display Options
• The Digital Pen
• Multi-User Mode
• Annotating the Screen
• Note on Mobi 360
• Screenshots
Classroom computer’s desktop - The classroom computer’s desktop and any documents or programs
opened from the desktop
Whiteboard mode - A plain white screen as a background for drawing or writing.
Display Screenshots - Screen captures (called screenshots) taken during the same class session.

Mobi 360™ 17
Display Options
• Displaying the Computer Screen from the Mobi 360
• Displaying Whiteboard Mode from the Mobi 360
• Using the Curtain to Hide the Screen
DISPLAYING THE COMPUTER SCREEN FROM THE MOBI 360
The Mobi 360 allows you to control your computer desktop from anywhere in the room.
If your computer is connected to a projector or large monitor, students can also view your computer desktop. This means
that you can use Mobi 360 to present documents, Microsoft PowerPoint presentations, web pages, videos and other
media from your computer.
How to display the computer screen from the Mobi 360...
1 Tap Lesson.
2 Tap Display.
3 Tap Computer Desktop.
DISPLAYING WHITEBOARD MODE FROM THE MOBI 360
If your classroom computer is connected to a projector or large monitor, you can use the Mobi 360 to project a white
background visible to all students in the class. The white background can be used like a whiteboard on which you or
students can “draw” or “write” on the screen from the Mobi 360.
How to display whiteboard mode from the Mobi 360...
1 Tap Lesson.
2 Tap Display.
3 Tap Whiteboard.
NOTE
You can use the other Mobi 360 digital pen tools to annotate the computer
screen. Such annotations are simply overlaid on the screen and will not
affect the underlying content.

Mobi 360™ 18
USING THE CURTAIN TO HIDE THE SCREEN
Tapping Curtain in the Lesson Zone displays a large black rectangle over the classroom computer desktop. This
effectively covers the screen to hide the items (such as a CueTag) behind the curtain. You can move or resize the curtain
to partially reveal the screen.
How to use the curtain to hide the screen...
1 From the Lesson Zone, tap the Curtain icon.
The curtain appears on the screen and a blue box surrounds the selected Curtain icon.
2 To move the Curtain:
a With the curtain showing, tap and hold the digital pen onto the Mobi 360 writing area. The screen cursor changes
to a hand.
b Move the pen as you want the curtain moved.
3 To resize the Curtain:
a The curtain has four resizing “handles,” one on each of its four sides. With the digital pen hovering over the Mobi
360 writing area, move the Pen over a Curtain handle. The cursor changes into a two-way arrow.
b Press and drag the tip of the pen to the desired location.
c Repeat for other curtain sides if necessary.
4 To remove the Curtain, tap the Curtain icon from the Lesson Zone.
The Curtain disappears and the blue box is removed from the Curtain icon.
NOTE
The Pen can be in any tool mode (for example: Mouse Pointer, Pen or
Highlighter) when moving or resizing the curtain.

Mobi 360™ 19
The Digital Pen
USING THE PEN AS A MOUSE POINTER
Using the pen as a mouse pointer allows you to control the classroom computer desktop.
How to use the pen as a mouse pointer...
1 Tap Lesson.
2 Tap the Pointer icon.
• To point, hold and move the digital pen just above the Mobi 360 writing surface.
• To select an area, tap and drag the pen across the Mobi 360 writing surface.
• To click, tap the writing surface once.
• To right-click, press and hold the rocker button, tap once and release the rocker button.
USING THE PEN AS A PEN
In the Lesson Zone, tap Pen to use the Mobi 360 digital pen to write or draw on the Mobi 360 writing surface. Writings
and drawings done with the Mobi 360 digital pen on the Mobi 360 writing surface transfer immediately to the classroom
computer desktop.
How to use the pen as a pen...
1 Tap Lesson.
2 Tap the Pen icon.
• Tap and drag the pen across the Mobi 360 writing surface to write or draw.
• Using the Pen as a Mouse Pointer
• Using the Pen as a Pen
• Using the Pen as a Highlighter
• Using the Pen to Draw Shapes
• Using the Pen to Draw Straight Lines
• Using the Pen as an Eraser
• Using the Pen as a Keyboard
NOTE
The pen works on the primary display. It cannot cross to a second screen
on an extended desktop.
NOTE
The Mobi 360 digital pen does not contain any ink and cannot be used to
write or draw on anything other than the Mobi 360.

Mobi 360™ 20
• To draw a straight line hold the top rocker button down before touching the pen tip to the Mobi 360 writing surface,
drag the pen across the writing surface, then release the rocker button before lifting the pen from the writing
surface.
3 To change the pen color:
a From the Lesson Zone, tap the Pen icon.
b Tap the colored square.
A set of colored squares appears.
c Tap the square of the color of your choice.
4 To change the pen thickness:
a Tap the horizontal line.
Boxes with lines of varying thicknesses appear.
b Tap the line width of your choice.
USING THE PEN AS A HIGHLIGHTER
In the Lesson Zone, tap Highlighter to use the Mobi 360 digital pen to highlight content. The highlighter draws a wide
line in a light color and is used to draw attention to a particular item.
How to use the pen as a highlighter...
1 Tap Lesson.
2 Tap the Highlighter icon.
• To write or draw, tap and drag the pen across the Mobi 360 writing surface.
• To draw a straight line, hold the top rocker button down before touching the pen tip to the Mobi 360 writing surface,
drag the pen across the writing surface, then release the rocker button before lifting the pen from the writing
surface.
3 To change the pen color:
a From the Lesson Zone, tap the Pen icon.
b Tap the colored square.
A set of colored squares appears.
c Tap the square of the color of your choice.
NOTE
Use the same general procedures as listed above for changing the colors,
thicknesses, sizes and shapes of other tools, such as the Highlighter,
Shapes and Eraser.
TIP
Tap the Point icon to use the mouse point to control the classroom
computer desktop.

Mobi 360™ 21
4 To change the pen thickness:
a Tap the horizontal line.
Boxes with lines of varying thicknesses appear.
b Tap the line width of your choice.
USING THE PEN TO DRAW SHAPES
In the Lesson Zone, tap the Shape Tool to use the Mobi 360 digital pen to draw geometric shapes on the classroom
computer screen.
The shape tool offers several options:
• Solid shape or Outline shape
• Shapes - Rectangle/Square, Oval/Circle, Isosceles Triangle, Right Triangle
How to use the pen to draw shapes...
1 To select the Pen as the shape tool:
a Tap Lesson.
b Tap the Shape Tool icon.
2 To change the shape color and outline style:
a With the shape tool selected, tap Outline.
Outlined and solid shapes of various colors appear.
b Tap the shape color and style of your choice.
3 To change the shape:
a With the shape tool selected, tap Shape.
Four shapes appear.
b Tap the shape of your choice.
TIP
computer desktop.
TIP
computer desktop.

Mobi 360™ 22
USING THE PEN TO DRAW STRAIGHT LINES
You can draw straight lines with the Mobi 360 digital pen in two ways:
• With the pen or highlighter selected hold the top rocker button down before touching the pen tip to the Mobi 360 writing
surface, drag the pen across the writing surface, then release the rocker button before lifting the pen from the writing
surface.
• With the line tool selected drag the digital pen across the Mobi 360 writing surface.
How to use the pen to draw straight lines...
1 Tap Lesson.
2 Tap the Line Tool icon.
USING THE PEN AS AN ERASER
In the Lesson Zone, tap Eraser to use the digital pen to delete annotations that you placed on the classroom computer
screen using the Mobi 360 digital pen. The Eraser cannot delete content produced by another source such as a
Microsoft Word document or Internet web page. To delete all annotations, tap Delete.
How to use the pen as an eraser...
1 Tap Lesson.
2 Tap the Eraser icon.
3 To change the eraser size:
a With the Eraser selected, tap Size.
b Tap the eraser size of your choice.
TIP
computer desktop.
TIP
computer desktop.

Mobi 360™ 23
USING THE PEN AS A KEYBOARD
Use the Mobi 360 digital pen in Keyboard mode to type information into various documents and programs on the
classroom computer. The Keyboard mode inserts characters at the text cursor within a document or program.
How to use the pen as a keyboard...
1 Open the desired document or program on the classroom computer.
2 Tap Lesson to access the Lesson Zone.
3 Tap the Mouse Pointer icon.
4 Use the Mouse Pointer to tap where you want to insert text.
5 Tap the Keyboard icon.
6 Tap individual characters and buttons to insert the text into your document.
7 By default, the Mobi 360 beeps each time you tap a key in Keyboard mode. To turn off the beep, tap Mute.
8 To access letters, numbers and various symbols, tap the following buttons:
• ABC - Keyboard shows alphabetical characters
• 123 - Keyboard shows a number pad and mathematical symbols
• !@# - Keyboard shows various miscellaneous symbols
9 When finished, tap Back.
NOTE
Using the Pen as a keyboard is not available in the Insight 360 Teacher
app. The device keyboard automatically displays when needed.

Mobi 360™ 24
Multi-User Mode
The Mobi 360’s Multi-User mode allows the instructor and up to four users to write or draw on the projected computer
screen at the same time.
A Mobi family student device (such as an MobiView, Mobi Learner or Mobi KWIK), device with the Insight 360 Teacher or
Insight 360 Student app installed, or DualBoard must be connected to the Insight 360 system for each simultaneous
user.
A DualBoard provides connections for two students. In 4-way mode, the DualBoard will always occupy the bottom two
quadrants.
If at least one student device is running the Insight 360 Student app, the teaching device must be running the Insight 360
Teacher app. No other devices can connect to the Insight 360 Teacher app session except other devices running the
Insight 360 Student app or Insight 360 Web Access browser-based application. When all devices are running Insight 360
Teacher or Student applications, the Multi-user button engages Constructed Response mode.
Users can share the same space on the screen (called the Sandbox) or the screen can be split into two or four parts.
• If the screen is split, each student device is assigned to its own section of the screen. Devices are selected
automatically by the Mobi 360. Instructors using the Insight 360 Teacher app can assign devices to specific sections.
• The instructor’s Mobi 360 keeps its “teach class” capability and can annotate and control any part of the screen.
• The entire screen or individual sections can be quickly hidden, locked or erased using the Mobi 360.
• Insight 360 automatically captures and saves screenshots when you enter and exit Multi-user mode on the Mobi 360.
On the instructor’s device, any annotation that you can make in the Lesson Zone can also be done in Multi-user mode.
Tapping either of these buttons opens the corresponding screen on the Mobi 360. To exit that screen, tap Back.
• Entering Multi-User Mode on the Mobi 360
• Locking or Hiding the Screen in Multi-User Mode
• Exiting Multi-User Mode
ENTERING MULTI-USER MODE ON THE MOBI 360
Use Multi-user mode to simultaneously display input from more than one Mobi family device on the screen.
How to enter multi-user mode on the Mobi 360...
1 In the Lesson Zone, tap Multi-User.
2 Tap one of the following:
• Shared - all users share the same screen space
• 2-way - two users, each on their own half of the screen
• 4-way - four users, each on their own quadrant

Mobi 360™ 25
3 To keep the background constant while in Multi-user mode, tap Use Fixed Background.
4 Tap Start.
5 While in Multi-user mode, you have access to all of the tools in the Lesson Zone. However, connected student devices
can only use pen, eraser and delete all tools.
6 Multi-user mode is closed, the Mobi 360 saves the current background for later Multi-user sessions within the same
class session.
LOCKING OR HIDING THE SCREEN IN MULTI-USER MODE
As the instructor, you can quickly lock/unlock, hide or show information on the screen using the following icons:
You can hide or lock one or more quadrants of the Multi-user screen. This may be useful if a particular student is writing
or drawing something inappropriate on the screen. Hiding a portion of the screen allows Insight 360 to capture the
information written or drawn on the screen, but keep the content hidden from the rest of the class. You can show hidden
content if you choose.
NOTE
If Use Fixed Background is selected, the computer desktop will not be
available until Multi-user mode is closed. Screen division lines do not show
on the fixed background.
• Student tools show in a toolbox in a corner of the screen assigned to the learner device.
• By default, student devices are connected with the pen tool selected.
• Students can change pen color or eraser size by tapping and holding the corresponding icon in the
toolbox, then tapping the option in the expanded toolbox.
• Each student can delete everything drawn from his own student device by tapping Delete All.
• If a student is using a Mobi 360 as a learner device, the Hide/Show and Lock/Unlock icons will show in
the Mobi 360 digital screen. These icons are indicators of the student device’s status; the student
cannot use these to hide/show the annotations or lock/unlock the device.
Hide – annotations are currently showing; tap to hide annotations in the selected region
Lock – region is currently unlocked; tap to lock the region (users cannot continue annotating)
Show – annotations are currently hidden; tap to show annotations in the selected region
Unlock – region is currently locked; tap to unlock region for annotation
NOTE
The Hide/Show and Lock/Unlock icons are toggles showing the current
state of the screen.

Mobi 360™ 26
How to lock or hide the screen in multi-user mode...
1 To lock or hide the entire screen:
a Start Multi-user mode.
b Tap the Lock icon near the top center of the Mobi 360 screen.
c From the All menu, tap the Lock or Hide icon.
The entire screen will be locked or annotations hidden.
d To return to Multi-user mode, tap Back.
2 To lock or hide a portion of the screen:
a In Multi-user mode, tap the Lock icon near the top center of the Mobi 360 screen.
b In the section of the Mobi 360 screen corresponding to the section you want to lock or hide on the classroom
computer screen, tap the Lock or Hide icon. That section of the screen will be locked or annotations hidden.
c To return to Multi-user mode, tap Back.
EXITING MULTI-USER MODE
Insight 360 saves a screenshot when you exit Multi-user mode.
How to exit Multi-user mode...
1 Tap Exit in the upper left corner of the Multi-user mode screen.
2 Tap Yes.
NOTE
These icons are toggles. To unlock or show annotations on the screen, tap
the corresponding button again.
NOTE
These icons are toggles. To unlock or show annotations on the screen, tap
the corresponding button again.

Mobi 360™ 27
Annotating the Screen
You can use the Mobi 360 digital pen as a mouse pointer, an annotation tool, or to control the Mobi 360. The Lesson
Zone contains the various pen annotation tools and options.
As an annotation tool, the digital pen can:
• Draw or write free form text in various colors on the screen
• Highlight objects in various colors on the screen
• Place lines and geometric shapes on the screen
• Erase annotations on the screen
• Annotation Icons
• Hiding Annotations
• Deleting Annotations
Annotation Icons
The Lesson Zone contains the following annotation icons:
NOTE
The pen works on the primary display. It cannot cross to a second screen
on an extended desktop.
Mouse Pointer - Uses the pen as a mouse to
control the classroom computer.
Thickness – Changes the thickness of the
selected annotation tool.
Pen – Writes or draws free form lines.
Shape – Changes the Shape tool’s geometric
shape.
Highlighter – Highlights existing area on the
screen.
Size – Changes the Eraser tool size.
Shape Tool – Draws geometric shapes.
Undo – Reverses the most recent action;
available for last 20 actions.
Line Tool – Draws a straight line.
Redo – Reapplies the effect of the most recent
“Undo” action; available for last 20 actions.
Eraser – Erases Mobi 360 annotations touched
by the eraser.
Hide /Show – Hides or shows all annotations on
the screen.
Color – Changes the color or outline properties
of the selected annotation tool.
Delete – Removes all annotations on the
screen.

Mobi 360™ 28
HIDING ANNOTATIONS
Using the Mobi 360, you can hide all annotations currently displayed on the classroom computer screen. Hiding
annotations temporarily removes all writings and drawings generated by the Mobi 360 from the classroom computer
screen. The Hide/Show button is a toggle that shows the current state. You can show hidden annotations by tapping
Hide/Show.
How to hide annotations...
1 From the Lesson Zone, tap the Hide/Show button.
DELETING ANNOTATIONS
Using the Mobi 360, you can delete (or clear) all annotations currently showing on the classroom computer screen.
Deleting annotations permanently removes all writings and drawings generated by the Mobi 360 from the classroom
computer screen. To delete just a portion of the screen, use the digital pen with the Eraser tool.
How to delete annotations...
1 From the Lesson Zone, tap the Delete button.
NOTE
If you are in Multi-user mode, you can tap Unlock to access individual
Hide icons for different parts of the screen. See Locking or Hiding the
Screen in Multi-User Mode for more information.

Mobi 360™ 29
Note on Mobi 360
You can create and display a Note relating to the current class session on the Mobi 360 and the Insight 360 Teacher app.
Tapping Note in the Lesson Zone opens Note View. The Note View contains Pen, Mouse Point and Eraser tools. Options
for writing, erasing, deleting and displaying a Note are provided along with color and line width options. Notes are saved
only for the duration of the current class and are deleted when the class ends.
The Note Pen tool works the same as the Lesson Zone’s digital pen. In Note View, you can write directly on the Mobi 360
screen or on the normal writing area to compose Note.
To access the Note Pen tool, tap Note from the Lesson Zone (The Pen tool is selected by default.). Alternatively, Tap
Pen from the Note View.
• Note Icons
• Creating and Displaying a New Note
• Using the Mouse Pointer in Note View
• Using the Eraser in Note View
• Displaying a Previous Note
• Deleting a Note
Note Icons
Note View contains the following icons:
Mouse Pointer – Uses the pen as a computer
mouse while in Note View.
Scroll Left, Scroll Right – Scroll through saved
notes.
Pen – Writes or draws free form lines. New Note – Creates a new blank note.
Eraser – Erases on the current note only.
Display Note – Displays the currently selected
note on the screen
Color – Changes the color of the selected pen
line in Note View.
Delete Note – Permanently deletes the currently
selected note (Mobi 360 only).
Background – Changes the note’s background
color.
Delete Note – Permanently deletes the currently
selected note (Insight 360 Teacher app only).
Thickness – Changes the thickness of the pen
line in Note View.
Back – Exits Note View and returns to the
Lesson Zone.

Mobi 360™ 30
CREATING AND DISPLAYING A NEW NOTE
Use Note View to create Note on the Mobi 360 and display them on your classroom computer. Notes are used to
temporarily display information on the Mobi 360 or on the classroom computer screen during a specific class session.
When displayed on the classroom computer screen, a colored or transparent background surrounds the note text.
How to create and display a new note...
1 Tap the New Note icon.
2 Use the digital pen to write or draw on the Mobi 360 screen or writing area.
3 To change the pen color, tap Color and then tap a new color.
4 To change the note’s background color, tap the Background icon and then tap a new color.
5 Tap the Thickness icon and then tap a new line to change the pen thickness.
6 Tap the Display Note icon to show the note on the classroom computer screen.
7 To return to the Lesson Zone, tap the Back icon.
USING THE MOUSE POINTER IN NOTE VIEW
You can use the Mouse Pointer to:
• Move Note on the computer screen
• Resize Note on the computer screen
• Delete Note from the computer screen
• Control the computer using the digital pen as a mouse
How to use the mouse point in Note View...
1 From the Lesson Zone, tap the Note icon.
2 Tap the Mouse Pointer icon.
TIP
Selecting Transparent removes the note background to give the
appearance of writing directly on the screen.
To change the color of a displayed note, select the note, tap Background,
then tap the Display Note icon.

Mobi 360™ 31
USING THE ERASER IN NOTE VIEW
The Eraser deletes annotations on the current note on the Mobi 360 screen.
How to use the eraser in Note View...
1 From the Lesson Zone, tap the Note icon.
2 Tap the Scroll Left icon until the desired note appears on the Mobi 360 screen.
3 Tap the Eraser icon.
4 Move the Eraser across the portion of the note displayed on the Mobi 360 screen that you want to erase.
5 Tap the Pen icon and update the note as desired.
6 Tap the Display Note icon to show the updated note on the classroom computer desktop.
7 To exit Note View, tap Back.
DISPLAYING A PREVIOUS NOTE
Notes are automatically saved as they are created. The number of notes created in this class session are displayed in
the lower-right corner of the Note View.
You can display these Note on the Mobi 360 or on the classroom computer. On the Mobi 360, only one note can display
at a time. Multiple Notes can be displayed on the classroom computer desktop. Up to 20 Notes may be created during
each class session. All Notes are deleted when the session ends. Insight 360 does NOT save session Notes.
How to display a previous note...
1 Tap the Scroll Left icon until the desired note appears on the Mobi 360 screen.
2 Tap the Display Note icon to show the current note on the classroom computer desktop.
3 To change the color of a displayed Note, tap the Note, tap Background, then tap the Display Note icon.
NOTE
Notes are saved only for the duration of the class session. You cannot
retrieve a Note created in a previous session.

Mobi 360™ 32
DELETING A NOTE
You can delete a note from the computer screen or permanently delete the note from the Mobi 360.
How to delete a note...
1 To delete a Note from the computer screen:
a With the Mouse Pointer tool, click X in the top corner of the note.
2 To delete a Note from the Mobi 360:
a In Note View, tap the Scroll Left icon or the Scroll Right icon to find the desired note.
b Tap the Delete Note icon.
NOTE
Deleting a note from the computer screen does not delete the note from
the Mobi 360.
NOTE
Deleting a note from Note View permanently deletes the note. There is no
Undo for this action, and the deleted note cannot be retrieved.

Mobi 360™ 33
Screenshots
A screenshot is an image of the classroom computer screen at a particular point in a class session. The Screenshot
feature saves an image of the classroom computer screen.
• Saving Screenshots with the Mobi 360
• Displaying Screenshots
• Using the Screenshot Sorter
• Annotating Screenshots with the Mobi 360
• Accessing Screenshots from Insight 360
SAVING SCREENSHOTS WITH THE MOBI 360
To save screenshots with the Mobi 360, follow the steps below.
How to save a screenshot with the Mobi 360...
1 From the Lesson Zone, tap the Screenshot icon.
The number in Screenshots Display increases by one.
The screenshots are saved in a folder on the classroom computer’s hard drive. Insight 360 will store a maximum of
10,000 screenshots per session. The total number of screenshots saved is limited by the size of your computer’s hard
drive.
DISPLAYING SCREENSHOTS
You can display screenshots on the classroom computer desktop in two ways:
• Screenshot Sorter - Displays thumbnails of all screenshots saved in the lesson.
• Screenshots Display mode - Displays full-size screenshots one at a time. Displayed screenshots are bordered in white
and contain a numeric identification in the upper left corner.
When you enter Screenshots Display mode, the last saved screenshot initially appears on the classroom computer
screen bordered in white. A numeric identification (such as 1/3 to indicate 1 of 3 screenshots) is displayed in the upper
left corner. The Mobi 360 provides arrows to scroll through saved screenshots.
NOTE
Insight 360 automatically saves screenshots during the following actions:
• Entering/Exiting Multi-user or Constructed Response mode
• Starting a Verbal Question
• Starting a Tagged Question
• After Editing a Captured Screenshot

Mobi 360™ 34
How to display screenshots...
1 From the Lesson Zone, tap Screenshots Display.
The most recent screenshot appears.
2 To access previous screenshots, tap the left arrow next to Screenshots Display.
3 To exit Screenshots Display mode, tap Desktop Display or Whiteboard Display.
USING THE SCREENSHOT SORTER
The Sorter displays icons for five categories of screenshots:
By default, screenshots from all categories display when the Sorter first opens. You can view screenshots only from a
certain category by turning off the non-desired categories.
How to use the screenshot sorter...
1 In Lesson mode, tap the Screenshot Sorter icon.
Thumbnails of screenshots display on the left side of the classroom computer screen.
2 Tap the screenshot you want to display.
3 To close the screenshot, tap Desktop Display or Whiteboard Display.
ANNOTATING SCREENSHOTS WITH THE MOBI 360
In Screenshot mode, you can use any annotation tool to make changes to the current screenshot. When you navigate
away from that screenshot using either the screenshot navigation arrows or by changing the display option, Insight 360
automatically captures a new screenshot with the changes. Once you end a class session, the screenshots are saved by
Insight 360.
How to edit screenshots with the Mobi 360...
1 Access the desired screenshot.
User-triggered ExamView Questions
Verbal Questions
Multi-user or Constructed Response
mode
Tagged Questions
TIP
If too many screenshots are displaying, tap the Sorter icons that are NOT
related to the category of screenshot you are looking for, and then tap the
screenshot you want to display.
For example: If you are looking for a Verbal Question screenshot, tap the
three icons OTHER than the Verbal Question icon.

Mobi 360™ 35
2 Use an annotation tool to make changes to the screenshot.
3 To save changes, click the screenshot navigation arrow or change the display option to Computer Desktop or
Whiteboard.
Accessing Screenshots from Insight 360
Insight 360 stores screenshots captured by the Mobi 360 in a folder on the classroom computer’s hard drive.
Once a session is ended, you can no longer view the screenshots from the Mobi 360. However, you can view
screenshots for a session through the Session Content Report in Insight 360.
NOTE
All favorites, classes, student data, tests, screenshots and other Insight
360 information reside on the classroom computer used to set up this data.
It will not be accessible if you take the Mobi 360 to another classroom even
if that classroom computer is running Insight 360, unless you have also set
up that computer with the same classes, students, favorites and other
data.

Mobi 360™ 36
QUESTION ZONE
The Question Zone allows you to:
• Ask Verbal, Tagged and ExamView questions during instruction
• Receive instantaneous feedback from students through student devices
• Set a timer to limit student response time
• View a Student Response Grid
• View initial question results
To access the Question Zone, tap Question at the bottom of the Mobi 360 screen.
The Question Zone contains there icons:
The four Question Zone icons toggle the corresponding items on and off the screen. Tap once to view and tap again to
hide.
Verbal - Impromptu questions set up on the Mobi 360.
Tagged - Written questions in existing course materials that have been electronically tagged for use with
the Insight 360 system.
ExamView - Instructor-led ExamView questions asked during instruction.
Timer - Displays the timer on screen for students to view.
Student Response Grid - Displays a grid indicating which student response systems have entered a
response to the current question.
Response Distribution Chart - Displays the Response Distribution Chart on screen for students to view.
Show/Hide Correct Answer - Only available when the Response Distribution Chart is showing. Displays
the correct answer in green on the Response Distribution Chart. When toggled off, all answers on the chart
display in blue.
• Asking Verbal Questions During Instruction
• Asking Tagged Questions
• Asking ExamView Questions
• Timing Student Questions
• Initial Question Feedback
• Displaying the Student Response Grid on-Screen
• Displaying Question Results on-screen

Mobi 360™ 37
ASKING VERBAL QUESTIONS DURING INSTRUCTION
Verbal questions allow you to set up an impromptu question and receive feedback through student response systems.
You can ask the following types of questions through the Verbal Questions tab: True/False, Yes/No, Numeric, Multiple
Choice (up to six options), Multiple Answer and Short Answer.
How to ask verbal questions during instruction...
1 From the Lesson Zone, tap Question.
The Verbal Question tab is displayed by default.
2 Tap Type, and then tap the button corresponding to the type of question.
3 Tap 123 to use numbered options instead of lettered options for Multiple Choice or Multiple Answer questions.
4 Tap Back.
5 Tap Answer, and then tap the correct answer or answers.
6 Tap Back.
7 Tap Timer to set the timer. Tap Plus or Minus to set the timer with more or less time.
8 Ask your students the question and include all options (if multiple choice). Request students to answer by pressing
the corresponding key on their student response systems.
9 Tap Start.
10 If all students answer the question before the timer is finished, tap Stop.
11 To start another question from the Question Zone, tap New.
NOTE
Numeric, Multiple Answer, and Short Answer question types are only
supported with Pulse 360 and Insight 360 Student app devices.
NOTE
If you do not specify a correct answer (such as if you are asking poll
questions), Mobi 360 cannot display correct, incorrect or percentage
correct information in the initial feedback. Mobi 360 only displays the
number of students who answered the question. To get specific answer
data, tap Results.
TIP
You may want to write the question and options using Whiteboard mode.

Mobi 360™ 38
ASKING TAGGED QUESTIONS
When the tagged question is visible on your classroom computer screen, the tagged question icon will be active.
How to ask tagged questions...
1 Tap the Question Zone icon.
2 Tap Timer to set the timer. Tap Plus or Minus to set the timer with more or less time.
3 Ask your students the question and include all options (if multiple choice). Request students to answer by pressing
the corresponding key on their clickers.
4 Tap Start.
5 If all students answer the question before the timer is finished, tap Stop.
ASKING EXAMVIEW QUESTIONS
You can use the Mobi 360 to ask an individual ExamView questions during instruction.
The entire ExamView file will open. If the question you want to ask is not at the beginning of the file, use the Scroll Left
and Scroll Right buttons on the Mobi 360 to navigate to the applicable question.
If the ExamView test file contains questions that are not supported by the student response system (such as Short
Answer for Spark 360 or Essay for Pulse 360/Spark 360), the Start button will not be enabled on those questions.
However, you can still use the material as background to ask a Verbal question instead.
If an ExamView question has been authored as a dynamic question, you can use the Recalc button to present the
question with new variables and new answer options.
How to ask ExamView questions...
1 From the Lesson Zone, tap Question.
2 Tap the ExamView question tab.
3 Tap the ExamView icon to open an ExamView test.
4 Find and tap an ExamView file that you have placed in Favorites.
The ExamView test opens on your desktop.
5 To set the timer, tap Timer. Tap Plus or Minus to set the timer with more or less time.
6 Tap Start.
7 When students are finished answering the question, tap Stop.
8 To show the ExamView feedback, use the digital pen as a mouse pointer and click Feedback on the ExamView
question slide.
NOTE
To start an ExamView question not in Favorites, use the digital pen as a
mouse pointer to browse for an ExamView file.

Mobi 360™ 39
9 To advance to the next ExamView question, tap the Scroll Right icon above Start on the Mobi 360.
10 If the Recalc button is enabled, you can tap this button to present the same question with new variables and answer
options.
TIMING STUDENT QUESTIONS
The default setting for the Question Zone timer is off. You can use the timer to time any Verbal, Tagged or ExamView
question.
How to time student questions...
1 Tap Timer to turn on the timer. Tap again to turn off the timer.
The default time is one minute, 30 seconds (1:30). You can increase or decrease the allotted time in 15 second
increments.
2 Tap Plus to increase time. Tap Minus to decrease time.
3 When Start is clicked, the timer is displayed at the top of the Mobi 360 screen.
When the timer ends, students cannot enter answers on their student devices. To allow students to finish answering
the question, tap Resume.
4 To display the timer on-screen, tap the Timer icon in the upper-right corner of the Question Zone.
The On Screen Timer opens on the classroom computer desktop.
5 If all students answer the question before the timer reaches zero seconds, tap Stop to stop the timer.
NOTE
The new allotted time becomes the new default time for the duration of the
class session.

Mobi 360™ 40
Initial Question Feedback
After at least one student has responded to a question, Mobi 360 provides instantaneous feedback as described below.
If a Short Description was entered for a Tagged question, the question description text appears in the question feedback
on the Mobi 360. For Verbal and ExamView questions, this appears as the word Question.
DISPLAYING THE STUDENT RESPONSE GRID ON-SCREEN
You can display a Student Response Grid on the classroom computer screen so students can determine whether Insight
360 has accepted the answers from their student devices. Each numbered block corresponds to an enrolled student.
How to display the student response grid on the screen...
1 In the upper-right corner of the Question Zone, tap the Grid icon.
The Student Response Grid appears at the top of the classroom computer desktop.
• A white block indicates that a student is enrolled in class.
• A gray block indicates that a student devices has joined the class session.
• A blue block indicates that Insight 360 has recorded the student’s response from his/her device.
DISPLAYING QUESTION RESULTS ON-SCREEN
You can display the results of a question on the classroom computer screen from the Question Zone. Results can be
displayed immediately after the question is started and are updated in real-time. Individual question results are available
until a new question is started. You cannot display the question results from a previous question.
How to display question results on-screen...
1 From the Question Zone, start a Verbal or Tagged Question.
2 Tap Response Distribution Chart.
NOTE
If you do not specify a correct answer for a Verbal or Tagged question
(such as if you are asking a poll question), Mobi 360 cannot display
correct, incorrect or percentage correct information. Mobi 360 only
displays the number of students.
Students - The number of student response systems joined in this session
Correct - The number of correct student responses
Incorrect - The number of incorrect student responses
Percentage - The percentage of correct responses versus total responses

Mobi 360™ 41
The Response Distribution Chart appears on the classroom computer screen.
3 To display the correct answer, tap the Show/Hide Correct Answer icon.
The correct answer is displayed in green.
NOTE
The chart will refresh when a new question is asked. If you do not want the
real-time results viewable by students, close the Response Distribution
Chart before starting the next question.

Mobi 360™ 42
RESULTS ZONE
The Results Zone provides two types of question results.
• Question-specific results of the most recent Verbal, Tagged or ExamView question which can be viewed with the
Response Distribution, Response Grid and Student Performance Charts
• Cumulative summary results for all questions in the current class session which can be viewed with the Performance
Summary or Item Summary Charts
• Results Zone Icons
• Viewing Reports
• Ending a Class Session
Results Zone Icons
VIEWING REPORTS
The Results Zone provides two types of question results.
• Question-specific results of the most recent Verbal, Tagged or ExamView question which can be viewed with the
Response Distribution, Response Grid and Student Performance Charts
• Cumulative summary results for all questions in the current class session which can be viewed with the Performance
Summary or Item Summary Charts
How to view reports on the Mobi 360...
1 Start a Verbal, Tagged or ExamView question in the Question Zone.
Response Distribution Chart Item Summary
Response Grid View Summary Charts
Student Performance View Question Charts
Performance Summary

Mobi 360™ 43
2 Tap Results, or from the Results Zone, tap the desired tab.
Response Distribution Chart The Response Distribution Chart displays the number of student responses for
each answer choice in the most recent question and is compatible with all
supported question types. The chart provides a summary of student responses
for an individual question and can be displayed on the classroom computer
desktop.
You can display this chart on-screen for students.
Student Response Grid
The Student Response Grid is compatible with all supported question types
and provides a color-coded grid of individual student responses for the current
question.
The total number of students who have answered the question is displayed in
the upper-left corner and automatically updates as students enter responses.
The Student Response Grid displays four rows of 10 student boxes by default;
more than 40 students can be viewed by using the scroll bar. The Student
Response Grid also displays the connected student response devices.
The Student Response Grid cannot be displayed on the classroom computer
screen.
• White - Student on class roster but has not joined the session.
• Gray - Student response pad is connected.
• Gray with red “X” - Pad was connected but has disconnected.
• Green - Student entered correct response or responded to a poll question
(no correct answer).
• Red with gray “X” - Student entered incorrect response.
Student Performance Table
The Student Performance Table lists question responses by student name and
is compatible with all supported question types. Icons indicate whether each
answer is correct or incorrect. A series of dashes indicates that a connected
student has not yet responded to the question. The list can be sorted by
student response pad number, correct responses or incorrect responses.
To sort the information, tap the Sort icon then tap the button matching the type
of sort you want to see.
The table will appear slightly different for short answer questions to
accommodate the responses.

Mobi 360™ 44
ENDING A CLASS SESSION
A class session does not end in Insight 360 until you tap End Class. If the device hibernates or is turned off, it will
resume the current class session until the class is ended on the device.
Insight 360 saves class session information while the session runs. When you end a class session, the Insight 360
software makes the session information available for review and editing. This information may include session date and
start time, Screenshots and Question Results.
You can retrieve session information in My Results in Insight 360.
How to end a class session...
1 Tap Class.
2 Tap End Class.
Performance Summary
The Performance Summary displays the student name, number of correct
answers and percentage of correct answers. The list can be sorted by student
response pad number, lowest score or highest score. The Performance
Summary is similar to the Student Performance Summary report on the Insight
360 software’s My Results tab.
Six students are displayed; use the scroll bar to view additional students.
Anonymous students have score of zero (0) even if they answer the question
correctly.
The Performance Summary cannot be displayed on the classroom computer
screen.
Item Summary
The Item Summary displays session question data by question number. The
Item Summary also displays number of students who answered correctly,
number of students who answered incorrectly, class percentage of correct
answers, and type of question. The Item Summary is similar to the Question
Analysis report on the My Results tab in the Insight 360 software.
The list can be filtered by question type.
Six questions are displayed; use the scroll bar to view additional questions. By
default, all question types show, to filter them tap Filter.
The Item Summary cannot be displayed on the classroom computer screen.

Mobi 360™ 45
CONTACT US
For additional help installing, configuring and using Mobi 360, contact Turning Technologies Technical Support.
Technical Support is available Monday - Friday, 5:00 a.m. - 5:00 p.m. MST.
From within the contiguous United States, you can reach Technical Support toll-free by calling 866.746.3015. If you are
calling from outside of the United States, please call +1.330.746.3015.
Technical Support may also be reached via e-mail at support@einstruction.com, a brand of Turning Technologies.
You can also browse our Knowledge Base, or reach us via Live Chat available from 6:00 a.m. - 3:00 p.m. MST.
Office Locations
Ohio
255 West Federal Street
Youngstown, Ohio 44503
Toll-Free: 866.746.3015
International: +1.330.746.3015
Arizona
7400 East Tierra Buena Lane, Suite 103
Scottsdale, Arizona 85260
Toll-Free: 866.746.3015
Paris
26/36 rue Alfred Nobel
93600 Aulnay-sous-Bois
Toll-Free: 866.746.3015
Support: +33 1.58.31.10.65
Belfast
19 Colvin House
Dundonald Enterprise Park
Carrowreagh Road
Belfast BT16 1QT, UK
Toll-Free: 866.746.3015

Mobi360 user guide

Recomendados

Recomendados

Más contenido relacionado

La actualidad más candente

La actualidad más candente (20)

Destacado

Destacado (7)

Similar a Mobi360 user guide

Similar a Mobi360 user guide (20)

Más de William McIntosh

Más de William McIntosh (20)

Último

Último (20)

Mobi360 user guide