ok datasheet.

1. C8051F044
25 MIPS, 64 kB Flash, 10-Bit ADC, 100-Pin Mixed-Signal MCU
Analog Peripherals High-Speed 8051 µC Core
10-Bit ADC - Pipelined instruction architecture; executes 70% of instructions in 1 or 2
- ±1 LSB INL; guaranteed monotonic system clocks
- Programmable throughput up to 100 ksps - Up to 25 MIPS throughput with 25 MHz system clock
- 13 external inputs; programmable as single-ended or differential - Expanded interrupt handler
- Programmable amplifier gain: 16, 8, 4, 2, 1, 0.5 Memory
- Data-dependent windowed interrupt generator - 4352 bytes data RAM
- Built-in temperature sensor (±3 °C) - 64 kB Flash; in-system programmable in 512-byte sectors (512 bytes
High-Voltage Differential Amplifier are reserved)
- 60 V common mode input range
- External parallel data memory interface
- Offset adjust from –60 to +60 V CAN Bus 2.0B
- 16 gain settings from 0.05 to 16 - 32 message objects
Three Comparators - ”Mailbox" implementation only interrupts CPU when needed
Internal Voltage Reference Digital Peripherals
Precision VDD Monitor/Brown-out Detector - 64 port I/O; all are 5 V tolerant
On-Chip JTAG Debug & Boundary Scan - Hardware SMBus™ (I2C™ compatible), SPI™, and two UART serial
- On-chip debug circuitry facilitates full speed, non-intrusive in-system ports available concurrently
debug (no emulator required) - Programmable 16-bit counter array with 6 capture/compare modules
- Provides breakpoints, single stepping, watchpoints, stack monitor, pro- - 5 general-purpose 16-bit counter/timers
gram trace memory - Dedicated watchdog timer; bidirectional reset
- Inspect/modify memory and registers - Real-time clock mode using timer 3 or PCA
- Superior performance to emulation systems using ICE-chips, target Clock Sources
pods, and sockets
- IEEE1149.1 compliant boundary scan - Internal programmable 2% oscillator: up to 25 MHz
Supply Voltage: 2.7 to 3.6 V - External oscillator: Crystal, RC, C, or Clock
- Typical operating current: 10 mA at 25 MHz
Package
- Multiple power saving sleep and shutdown modes - 100-pin TQFP (standard lead and lead-free packages)
Temperature Range: –40 to +85 °C Ordering Part Numbers
- Lead-free package: C8051F044-GQ
- Standard package: C8051F044
VDD
VDD Digital Power
UART0 P0 P0.0
8
VDD
DGND UART1 Drv P0.7
DGND
DGND
SFR Bus SMBus C
AV+
AV+ Analog Power 0 SPI Bus
R P1 P1.0
AV+ O Drv P1.7
AGND
AGND
AGND
5 PCA
Timers
S
S P2.0/CPx
TCK
TMS
TDI
JTAG
Logic
Boundary Scan
Debug HW
1 0,1,2,3,4
B
A
P2
Drv P2.7/CPx
TDO Port
RST Reset 64 kB 0,1,2,3 R
&4 P3.0/AINAMUX0
FLASH P3
Latches Drv
MONEN
VDD
Monitor
WDT C 32x136
P3.7/AINAMUX7
CAN CANTX
XTAL1
XTAL2
External
Oscillator
o CANRAM
2.0B CANRX
Circuit 256 byte
r
System
Clock
VREF VREF
RAM
Internal
e 4 kB
XRAM +
P2.0
CP0 P2.1
2% -
P2.2
Oscillator +
CP1 P2.3
-
P2.4
+
CP2 P2.5
VREF0 -
AIN0.0
AIN0.1
AIN0.2
AIN0.3 P4.0
A ADC Port 4 <from crossbar> P4 P4.4
M Prog
100 ksps DRV P4.5/ALE
U Gain
External Data Memory Bus Bus Control
Ctrl Latch
P4.6/RD
X (10-Bit) P4.7/WR
P5 Latch P5.0/A0
P5
Address [15:0]
TEMP
SENSOR Addr [7:0] DRV P5.7/A7
A P6 Latch P6.0/A8
P6
M 8:2
Addr [15:8] DRV P6.7/A15
U
X P7.0/D0
HVAIN+ P7 Latch P7
HVAMP Data [7:0] DRV
Data Latch P7.7/D7
HVAIN-
HVREF
HVCAP
CAN 2.0B Copyright © 2005 by Silicon Laboratories 5.5.2005

2. C8051F044
25 MIPS, 64 kB Flash, 10-Bit ADC, 100-Pin Mixed-Signal MCU
Selected Electrical Specifications
(TA = –40 to +85 C°, VDD = 2.7 V unless otherwise specified)
Parameter Conditions Min Typ Max Units
Global Characteristics
Supply Voltage 2.7 — 3.6 V
Supply Current with Clock = 25 MHz — 10 — mA
CPU active Clock = 1 MHz 0.5 mA
Clock = 32 kHz; VDD Monitor Enabled 20 µA
Supply Current (shutdown) Oscillator off; VDD Monitor Disabled — 0.1 — µA
Clock Frequency Range DC — 25 MHz
A/D Converter
Resolution — 10 — bits
Integral Nonlinearity — — ±1 LSB
Differential Nonlinearity Guaranteed Monotonic ±1 LSB
Signal-to-Noise Plus 59 — — dB
Distortion
Throughput Rate — — 100 ksps
Input Voltage Range 0 — VREF V
Comparators
Supply Current (each Comparator) — 1.5 — µA
Response Time (CP+ – CP-) = 100 mV — 4 — µs
Package Information C8051F040DK Development Kit
D MIN NOM MAX
D1 (mm) (mm) (mm)
A - - 1.20
A1 0.05 - 0.15
A2 0.95 1.00 1.05
b 0.17 0.22 0.27
D - 16.00 -
E1 E D1 - 14.00 -
e - 0.50 -
E - 16.00 -
E1 - 14.00 -
100
PIN 1
DESIGNATOR
1
A2 e
A
b A1
CAN 2.0B Copyright © 2005 by Silicon Laboratories 5.5.2005
Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc.
Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders