1. assinment2-130115054729-phpapp01.doc
MET212- Fluid Mechanics & Machines
st
1 Octuber, 2011
10
Name…… ……… ……… …… ………… I.D No.…….… ………
Section: …….. date ………………………………………..
Q.1 Consider a U-tube manometer whose arms are open to the atmosphere. One
arm contains 70cm (hw1) high water and other arm contains light oil (SG=0.78) from the
other. If the other arm contains oil-water and the height ratio of 6 (h o=6hw2). Determine
the heights in meter of each fluid in the right arm of this U-tube manometer.
Q.2: A basic elements of a hydraulic jack are shown in Figure below for lifting a
car. If mechanical advantage at F1 and the area of piston A1 is 20-cm2 and A2 is
190-cm2, what load F2 can be raised for the car by a force of 60 N applied to the
smaller piston.
Dr. Adel Afify MET212 Octuber, 2011 1

2. assinment2-130115054729-phpapp01.doc
Q.3: Compare the pressure heads (h) of water, carbon tetrachloride and mercury
corresponding to a pressure of 50 kPa. Express your results in SI units.
(ρwater=1000kg/m3, ρmercury=13600kg/m3, ρcarbontetrachloride = 1590kg/m3)
Q.4: A closed tank is partially filled with glycerin. If the air pressure in the tank is
6 psi and the depth of glycerin is 10 ft, what is the pressure in psi at the bottom of
the tank? [ρglycerin= 2.44 slugs/ft3 and [(1 Lb =1 slugs x 1 ft/s2)]
Q.5: The lower half of a 10-m high cylindrical barrel is filled with water and the upper
half with oil. Determine the pressure difference (∆ P) in kPa between the bottom and top
of the cylinder.
Dr. Adel Afify MET212 Octuber, 2011 2

3. assinment2-130115054729-phpapp01.doc
Q.6: The top of an inverted U-tube manometer is filled with oil of specific gravity,
SGo=0.98 and the remainder of the tube with water of specific gravity SG w=1.01. Find the
pressure difference (PB - PA) in Pa between two points B and A at the same level at the
base of the legs when the manometer reading in oil-water level h is 75mm.
Q. 7: A rectangular gate located at h=3.048m below the surface of water (see Fig.).
Determine the magnitude of the force as well as the depth of application on the
rectangular gate of width 1.524m and height 1.828m and the gate is inclined at an angle
600 from the water surface level. ρwater= 999.52 kg/m3.
600
h
Water
Rectangular Gate
1.828m
Dr. Adel Afify MET212 Octuber, 2011 3

4. assinment2-130115054729-phpapp01.doc
Q.6: The top of an inverted U-tube manometer is filled with oil of specific gravity,
SGo=0.98 and the remainder of the tube with water of specific gravity SG w=1.01. Find the
pressure difference (PB - PA) in Pa between two points B and A at the same level at the
base of the legs when the manometer reading in oil-water level h is 75mm.
Q. 7: A rectangular gate located at h=3.048m below the surface of water (see Fig.).
Determine the magnitude of the force as well as the depth of application on the
rectangular gate of width 1.524m and height 1.828m and the gate is inclined at an angle
600 from the water surface level. ρwater= 999.52 kg/m3.
600
h
Water
Rectangular Gate
1.828m
Dr. Adel Afify MET212 Octuber, 2011 3

5. assinment2-130115054729-phpapp01.doc
Q.6: The top of an inverted U-tube manometer is filled with oil of specific gravity,
SGo=0.98 and the remainder of the tube with water of specific gravity SG w=1.01. Find the
pressure difference (PB - PA) in Pa between two points B and A at the same level at the
base of the legs when the manometer reading in oil-water level h is 75mm.
Q. 7: A rectangular gate located at h=3.048m below the surface of water (see Fig.).
Determine the magnitude of the force as well as the depth of application on the
rectangular gate of width 1.524m and height 1.828m and the gate is inclined at an angle
600 from the water surface level. ρwater= 999.52 kg/m3.
600
h
Water
Rectangular Gate
1.828m
Dr. Adel Afify MET212 Octuber, 2011 3

6. assinment2-130115054729-phpapp01.doc
Q.6: The top of an inverted U-tube manometer is filled with oil of specific gravity,
SGo=0.98 and the remainder of the tube with water of specific gravity SG w=1.01. Find the
pressure difference (PB - PA) in Pa between two points B and A at the same level at the
base of the legs when the manometer reading in oil-water level h is 75mm.
Q. 7: A rectangular gate located at h=3.048m below the surface of water (see Fig.).
Determine the magnitude of the force as well as the depth of application on the
rectangular gate of width 1.524m and height 1.828m and the gate is inclined at an angle
600 from the water surface level. ρwater= 999.52 kg/m3.
600
h
Water
Rectangular Gate
1.828m
Dr. Adel Afify MET212 Octuber, 2011 3