Uneak White's Personal Brand Exploration Presentation
Ic fab
1. Topic: Integrated Circuit Fabrication
Researched By: Johnmar T. Diamante ECE5A
What is an Integrated Circuit?
An integrated circuit (IC), sometimes called a chip or microchip, is a semiconductor wafer on which
thousands or millions of tiny resistors, capacitors, and transistors are fabricated. An IC can function as an
amplifier, oscillator, timer, counter, computer memory, or microprocessor. A particular IC is categorized
as either linear (analog) or digital, depending on its intended application.
Linear ICs have continuously variable output (theoretically capable of attaining an infinite number of
states) that depends on the input signal level. As the term implies, the output signal level is a linear
function of the input signal level. Ideally, when the instantaneous output is graphed against the
instantaneous input, the plot appears as a straight line. Linear ICs are used as audio-frequency (AF) and
radio-frequency (RF) amplifiers.
Digital ICs operate at only a few defined levels or states, rather than over a continuous range of signal
amplitudes. These devices are used in computers, computer networks, modems, and frequency
counters. The fundamental building blocks of digital ICs are logic gates, which work with binary data,
that is, signals that have only two different states, called low (logic 0) and high (logic 1).
Processes in IC Fabrication:
Silicon Wafer Fabrication:
1. Converting sand to silicon
Sand is composed of silica and is the starting point for making a silicon wafer. To extract the
element silicon from the silica, it must be reduced. This is accomplished by heating a mixture of
silica and carbon in an electric arc furnace to a temperature in excess of 2,000°C. Impurities such as
2. iron, aluminum, boron and phosphorous also react to give their chlorides, which are then removed
by fractional distillation. During the reaction, silicon is deposited on the surface of an electrically
heated ultra-pure silicon rod to produce a silicon ingot.
2. Creating a cylindrical crystal
To turn it into a usable material, the silicon must be turned into single crystals that have a regular
atomic structure. This transformation is achieved through the Czochralski Process. Electronic-grade
silicon is melted in a rotating quartz crucible and held at just above its melting point of 1,414°C.
3. Slicing the crystal into wafers
Integrated circuits are approximately linear, which is to say that they're formed on the surface of the
silicon. To maximize the surface area of silicon available for making chips, the silicon ingot is sliced
up into discs called wafers. The wafers are just thick enough to allow them to be handled safely
during semiconductor fabrication. 300mm wafers are typically 0.775mm thick. Sawing is carried out
using a wire saw that cuts multiple slices simultaneously, in the same way that some kitchen gadgets
cut an egg into several slices in a single operation.
4. Making a patterned oxide layer
The wafer is heated to a high temperature in a furnace. The wafer is spun in a vacuum so that the
photoresist spreads out evenly over the surface before being baked dry. The wafer is exposed to
ultraviolet light through a photographic mask or film. The next stage is to develop the latent circuit
image. The photoresist isn't sufficiently durable to withstand the hot gasses used in some steps, but
it is able to withstand hydrofluoric acid, which is now used to dissolve those parts of the silicon
oxide layer where the photoresist has been washed away. Finally, a solvent is used to remove the
remaining photoresist, leaving a patterned oxide layer in the shape of the required circuit features.
Wafer Testing:
Wafer testing is a step performed during semiconductor device
fabrication. During this step, performed before a wafer is sent to die
preparation, all individual integrated circuits that are present on the
wafer are tested for functional defects by applying special test
patterns to them. The wafer testing is performed by a piece of test
equipment called a wafer prober.
Wafer Mounting:
To facilitate the processing of the wafer at wafer saw, support is
provided to the wafer by mounting the wafer on dicing tape. The
dicing tape is a PVC sheet typically 3 mm in thickness with synthetic
adhesive on one side to hold both the wafer frame and the wafer.
3. Dicing or Wafer Sawing:
Wafer saw follows wafer mounting and is the step that actually cuts
the wafer into individual dice for assembly in IC packages. The wafer
saw process consists of the following steps:
1. The frame-mounted wafer is automatically aligned into
position for cutting;
2. The wafer is then cut thru its thickness according to the programmed die dimensions using a
resin-bonded diamond wheel rotating at a very high rpm;
3. The wafer goes through a cleaning process using high pressure DI water sprayed on the
rotating wafer and then dried by air-blowing.
Die Bonding or Die Attach:
Die Bonding is the process of attaching the silicon chip to
the die pad or die cavity of the support structure of the
semiconductor package. These are the two common die
attach processes:
1. Adhesive Die Attach - uses adhesives such as polyimide, epoxy and silver-filled glass as die
attach material to mount the die on the die pad or cavity. The adhesive is first dispensed in
controlled amounts on the die pad or cavity. The die for mounting is then ejected from the
wafer by one or more ejector needles. While being ejected, a pick-and-place tool commonly
known as a 'collet' then retrieves the die from the wafer tape and positions it on the
adhesive.
2. Eutectic Die Attach - is commonly employed in hermetic packages, uses a eutectic alloy to
attach the die to the cavity. A eutectic alloy is an alloy with the lowest melting point possible
for the metals combined in the alloy. The Au-Si eutectic alloy is the most commonly used die
attach alloy in semiconductor packaging.
Wire Bonding:
Wire bonding is the process of providing electrical connection between
the silicon chip and the external leads of the semiconductor device using
very fine bonding wires. The wire used in wire bonding is usually made
either of gold (Au) or aluminum (Al), although Cu wire bonding is starting
to gain a foothold in the semiconductor manufacturing industry. These
are the two common wire bonding processes:
1. Gold ball wire bonding - a gold ball is first formed by melting the end of the wire through
electronic flame-off (EFO). The free-air ball is then brought into contact with the bond pad.
Adequate amounts of pressure, heat, and ultrasonic forces are then applied to the ball for a
specific amount of time, forming the initial metallurgical weld between the ball and the
4. bond pad as well as deforming the ball bond itself into its final shape. The wire is then run to
the corresponding finger of the lead frame, forming a gradual arc or "loop" between the
bond pad and the lead finger. Pressure and ultrasonic forces are applied to the wire to form
the second bond, this time with the lead finger.
2. Aluminum wedge wire bonding - a clamped aluminum wire is brought in contact with the
aluminum bond pad. Ultrasonic energy is then applied to the wire for a specific duration
while being held down by a specific amount of force, forming the first wedge bond between
the wire and the bond pad. The wire is then run to the corresponding lead finger, against
which it is again pressed. The second bond is again formed by applying ultrasonic energy to
the wire. The wire is then broken off by clamping and movement of the wire.
Molding or IC encapsulation:
Molding is the process of encapsulating the device in plastic material.
Transfer molding is one of the most widely used molding processes in
the semiconductor industry because of its capability to mold small
parts with complex features. In this process, the molding compound is
first preheated prior to its loading into the molding chamber.
After pre-heating, the molding compound is forced by a hydraulic plunger into the pot where it reaches
melting temperature and becomes fluid. The plunger then continues to force the fluid molding
compound into the runners of the mold chase. These runners serve as canals where the fluid molding
compound travels until it reaches the cavities, which contain the lead frames for encapsulation.
Plating or Lead Finish:
Plating or Lead Finish is the process of applying a coat of metal over the leads of an IC to protect the
leads against corrosion, protect the leads against abrasion, improve the solderability of the leads and
improve the appearance of the leads. These are the two widely used lead finish techniques in the
semiconductor industry:
1. Tin plating - is a form of pure metal electroplating, which is the process of depositing a
coating of metal on a surface by passing a current through a conductive medium, or
electrolyte.
2. Solder plating - is a form of alloy plating. An alloy is composed of at least two elements, at
least one of which is a metal. An alloy has better properties than its component metals: it is
harder, more corrosion-resistant, has better solderability and better appearance.
5. Marking:
Marking is the process of putting identification, traceability, and distinguishing
marks on the package of an IC. The device name, company logo, date code,
and lot id are examples of information commonly marked on the IC's package.
Some marks are put on the package during Assembly and some marks are put
on the package during Test. These are the two common marking processes:
1. Laser marking - as the name implies, refers to the process of engraving marks on the
marking surface using a laser beam. There are many types of lasers, but the ones used or in
use in the semiconductor industry include the CO2 laser, the YAG laser, and diode lasers.
2. Ink marking - consists of transferring an ink pattern from the plate, which is a flat block with
pattern depressions that are filled with ink, to the package, using a silicone rubber stamp
pad. Silicone rubber repels ink, making the transfer of the ink pattern clean and efficient. It
is also resilient and elastic, making it possible to print even on uneven surfaces.
Deflash/ Trim & Form /IC Singulation:
Deflash - removal of flashes from the package of the newly molded parts.. Flashes are the excess plastic
material sticking out of the package edges right after molding.
Trim - cutting of the dambars that short the leads together.
Form - forming of the leads into the correct shape and position.
Singulation - cutting of the tie bars that attach the individual units to the lead frame, resulting in the
individual separation of each unit from the lead frame.
IC testing:
In this process, the IC’s are checked by an IC tester for physical and electrical defects. Defective IC’s are
retested by the previous processes to ascertain the cause of the defects.