1. Strategies for Effective Teaching
A Handbook for
Teaching Assistants
Graphic from Cooperative Learning Workshop, Karl Smith, University of Minnesota
Prepared by Teaching Assistant Fellows
University of Wisconsin - Madison
College of Engineering
Prepared Fall 1995

2. 1994-1995 College of Engineering TA Fellows:
Chemical Engineering: Electrical Engineering:
Prabhu Balaraman Muneer Khan
Engineering Mechanics: Industrial Engineering:
Mark Fleming David Nowicki
Mechanical Engineering:
Joe Lacey
Sandra Courter, Program Director, Teaching Improvement Program
Edited by: Sandra Courter, Prabhu Balaraman, Joe Lacey, and Clark Hochgraf
© Copyright 1996, University of Wisconsin System Board of Regents
The College of Engineering will update this handbook every year, as appropriate.
Reprinted or reproduced with permission. Please send requests or suggestions to:
Office of the Associate Dean of Academic Affairs
College of Engineering
University of Wisconsin
Room 2640, Engineering Hall, Madison, WI 53706.
Phone: (608) 262-4819

3. Table of Contents
I. PRACTICAL EXAMPLES
Connecting Theory with Applications .........................................................1
II. SHOW AND TELL
Reversing Student Roles ..............................................................................7
III. CASE STUDIES
Bringing “Real-Life” Scenarios into the Classroom ....................................9
IV. GUIDED DESIGN PROJECTS
Introducing Practical Design Experience in Classrooms .........................12
V. OPEN-ENDED LABS
Making Students Think Deeper.................................................................14
VI. THE FLOWCHART TECHNIQUE
Organizing the Flow of Thought ...............................................................19
VII. OPEN-ENDED QUIZZES
Moving Students Away From Memorization.............................................23
VIII. BRAINSTORMING
Encouraging Creativity .............................................................................25
IX. QUESTION-AND-ANSWER METHOD
Encouraging Student Participation ..........................................................29
X. SOFTWARE
Increasing Teaching Efficiency..................................................................32
XI. TEACHING IMPROVEMENT
Monitoring Your Progress .........................................................................35
XII. FAST FEEDBACK FORM
Contributing Your Ideas............................................................................36

4. Foreword
We help our students understand engineering concepts and go beyond the knowledge
level to higher levels of thinking. We help them to apply, analyze, and synthesize, to
create new knowledge, and solve new problems. So, too, as teachers, we need to
recognize our challenge to go beyond knowledge about effective teaching. We need to
apply these strategies, analyze what works, and take action to modify or synthesize our
learnings to help our students learn in a way that works for us as individuals and teams
of teachers.
The learning community consists of both students and teachers. Students benefit
from effective teaching and learning strategies inside and outside the classroom. This
Handbook focuses on teaching strategies you can use in the classroom to foster effective
learning.
Helping students learn is our challenge as teachers. Identifying effective teaching
strategies, therefore, is our challenge as we both assess the effectiveness of our current
teaching style and consider innovative ways to improve our teaching to match our
students' learning styles.
The mission of the College of Engineering, UW-Madison, is to "create, integrate,
transfer, and apply engineering knowledge." The strategic plan sets forth three broad
objectives to achieve and maintain, namely,
• educational excellence
• research leadership
• technology transfer leadership.
This Handbook is one resource to assist faculty, academic staff who teach, teaching
assistants, and undergraduate assistants as they strive to meet the objective of
"educational excellence."
COE faculty and teaching assistants have identified the ten categories of effective
teaching strategies described in this Handbook. Each description consists of an
introduction, scope, examples, and conclusions which include student responses to the
strategies. Our next version will contain references for each of the strategies.
You may have used these or similar strategies in your classroom with similar results.
Or you may have other examples, strategies and references that you'd like to share
within our teaching and learning community. Your additions and suggestions are
welcome. In fact, you'll notice a distinctive feedback form as the last page of this
Handbook.

5. With your assistance we can build a culture of continuous improvement in
undergraduate and graduate teaching here at UW-Madison. By so doing, you will help
facilitate an environment in which the College of Engineering becomes a learning
organization. Students will benefit!

6. I. PRACTICAL EXAMPLES
Connecting Theory with Applications
Students have expressed concern regarding the need for more industrial and
practical examples to reinforce theory in the classroom. The use of practical examples
can help you connect engineering theory with practical applications for more effective
teaching and learning. The introduction of practical examples does not imply an
elimination of theory, but rather an enhancement of the theory taught in the classroom.
It is important to simultaneously develop a theoretical and a practical base since neither
is useful without the other.
The use of practical examples in the classroom is targeted at the following two main
goals:
1. Help illustrate and explain new material making the theoretical basis of
the material more accessible to the students. Practical examples help
students understand the new concepts being introduced.
2. Teach students how to apply their knowledge of course material to new
situations that are not directly covered in class. The goal here is to show
the students not only that what they are learning has practical
applications, but more importantly, how to apply their understanding of
the basic principles to real engineering problems.
Scope
Practical examples can be included at all levels of the engineering curriculum. When
determining examples to be used for instruction it is important to make the examples as
clear and straight forward as possible. The key is to make the examples as simple as
possible, and to make sure that they isolate the desired principle. Whenever possible,
the examples should be designed so that the students’ physical senses are brought into
play. Examples that are likely to be enjoyed by the students include those that require
them to use their sense of sight, feeling, hearing or smell. The following guidelines
should be remembered when implementing practical examples:
1. Understand the example given and be able to explain it. If you cannot
provide a clear explanation to the example, the example will confuse the
students more than help them.
2. Before giving a demonstration or take home assignment, carry out the
assignment yourself. This will ensure that you know exactly what the
students will "see". It will also help you to anticipate your students’
-1-

7. questions. Giving an assignment or demonstration that doesn't work is
frustrating to the students and is bad for your credibility.
3. Choose examples that are relevant to the students. Examples that the
students can observe first hand as opposed to those in a film or on TV are
better. Try and find examples that the students can observe on campus
or at home. Pull examples from current events like, for instance,
explaining the cause for a design failure of a collapsed bridge recently in
the news. Explain the basic principles behind a new or commonly used
product like the fluid mechanics aspects of a Bernoulli disk drive in a
computer.
4. Allow ample time in class to discuss the example.
5. Consider having the students prepare a written report to document what
they have learned. Have them include a list of the basic principles
involved.
Categories and Types of Practical Examples
Practical examples can be grouped into two broad categories: A) those that help in the
Explanation of Theory and New Concepts, and B) those that illustrate the Application of
Basic Principles. In addition, practical examples can also be broken down into different
types based on the format in which they are used. For example, one can design practical
examples that are based on: a) analogies, b) observations, c) demonstrations
(experimental or mathematical), d) sensing phenomena, and e) observing secondary
effects.
Explanation of Practical Example Types
1. Analogy: The analogy is a very helpful tool for explaining new concepts. Here, the
instructor links the new concept to an idea which the students can easily picture in their
minds (Category A). An example of an analogy would be to explain the concept of the
conservation of energy in terms of money in a bank. One can imagine the money in a
checking account as being analogous to kinetic energy. Similarly, money in the savings
and money market accounts can be thought of as being analogous to pressure and
potential energies, respectively. Just as money can be transferred between the three
different accounts, so can energy between the three different forms. The concept of
frictional energy losses can now be easily related to the debiting of money from the
accounts (say, for paying the rent).
2. Observations: Observations that the student can make outside of class can help
demonstrate basic principles being currently studied in class. The example can be
-2-

8. carried out as a take home assignment where the students are required to go and
observe a phenomena that they can readily see, feel, hear and smell, and later
summarize their observations. The students bring their observations to class and the
instructor leads a discussion of what the students observed and what those observations
mean. This type of exercise not only helps with the understanding of a new concept or
basic principle but teaches the students how to observe a phenomena before trying to
analyze it. (Categories: A & B)
3. Demonstrations: (Experimental or Mathematical) The demonstration example can
be done either as an experimental exercise carried out in class with small experimental
models, or as a mathematical exercise carried out on the "chalkboard" to explain a
physical phenomena. This can be particularly instructive when the students are aware
of the phenomena but are not able to explain the science behind it. (Categories: A & B)
a) Experimental: An experimental demonstration requires physical equipment. While
finding the right equipment may not always be possible, some examples require
materials as simple as a paper clip or piece of paper. For instance, the factors affecting
the aerodynamic drag and lift forces on an object can be demonstrated with a simple
piece of writing paper. Hold a flat sheet of paper parallel to the floor and drop it
observing its rate of decent. Then take the same sheet of paper crumple it up, drop it
and observe its rate of decent. In both cases you have the same material, the same
mass, and the same gravitational force acting on the system. Therefore, these
parameters can be eliminated from consideration. By further eliminating other
parameters, the students can be lead to understand that the important parameter is the
aerodynamic drag acting on the two different objects. Similarly, important governing
parameters in other systems could be deduced. For instance, tests could be run with the
same object shapes but with different projected areas. By observing how the time of fall
depends on the various parameters, the students could arrive at the main governing
parameters.
b) Mathematical: The purpose of a mathematical demonstration would be to explain,
using the theory developed in class, the science behind some phenomena that the
students have seen or heard of. This can be particularly enlightening if the phenomena
is such that everyone knows about it, but few realize what really is happening. For
instance, the term valve float in an Internal Combustion engine can be explained by
modeling the valve as a train of solid links and springs, and then writing the equations
of motion for the valve.
4. Sensing: Sensing examples are designed so that students can “feel” the science
behind the phenomena. The goal here is to have the students carry out experiments that
-3-

9. allow them to sense the different parameters that enter into the theory. An excellent
example of this would be to study the relationship between speed and torque for a gear
system using a ten-speed bicycle. The students’ assignment would be to flip their ten
speed bicycle upside down, switch through all the gear combinations while pedaling it by
hand, and physically sense how the speed and torque for a particular gear setting are
related. Clearly, the emphasis in this technique is not to teach or explain a new concept
but to give a known concept more meaning by having the students sense it. (Category B)
5. Secondary Effects: Secondary effects demonstrate the fact that sometimes the
explanation of an engineering phenomenon is not obvious. The purpose here is to get the
students to really consider all the possible explanations besides the most obvious one. A
classic example of this would be the observation of the direction of movement of a
helium balloon tied to the floor of a car when the car accelerates. Typically one would
expect the balloon to move backwards when the car accelerates due to the inertia of the
balloon. This would be the case if a steel ball were to be suspended from the ceiling of a
car. In reality, the students will notice that the balloon moves forward as the car
accelerates. An investigation of the forces acting on the balloon can be done either as a
homework assignment or as a class discussion. By doing so, the students should
eventually come to realize that the balloon is pushed forward by the buoyancy force
acting on it. As the car accelerates, the air in the back of the car is compressed slightly,
resulting in a density gradient from the front to the rear of the car. The helium in the
balloon is lighter than air and therefore experiences a buoyancy force in the horizontal
direction.
More Practical Examples
1. Baseball Bat Fracture Example (Strength of Materials, Material Science)
(Categories: A & B; Example Types: Observations, Demonstrations and Secondary
effects)
Goal: Understand why the proper way to hold a wooden baseball bat is with the
trademark or label facing up.
This example demonstrates the need for critical observation and the application of
basic principles. As a first step towards finding a solution, the student needs to observe
or guess what would happen if the bat is not held the right way. The answer to this
(from either actually trying it out or by observing someone else do it) is that the bat is
likely to break. The next step is to apply the basic theoretical principles and rationalize
why this is so. The actual analytical process may proceed as below:
-4-

10. • Investigate how the bat is loaded and how it may fail. For instance, does
the bat fail in tension, torsion or bending?
• Realize that the bat, in this case, is acting like a short beam in bending
which implies that transverse shear can not be neglected (typical
assumption made in Strength of Materials class)
• Draw a free body diagram of the loading and a stress cube for the type of
loading present.
• Look at a baseball bat and sketch the cross-section of a baseball bat and
describe what is seen.
• Investigate how the orientation of the bat and, therefore, the wood fibers
might affect its ability to carry the loads (stresses) present.
• Look at a broken bat and draw conclusions as to what the mode of failure
was and how it relates to the orientation of the bat.
Conclusions: The students learn by making observations and by applying basic
theoretical principles that the bat is more resistant to shear stress with the label up.
The dependence is due to the orientation and size of the fibers in the growth rings which
affect the surface area of contact between fiber bundles. They learn that the bat should
be modeled as a short beam with a transverse load, and that a long beam assumption is
not appropriate in this situation.
2. Water Rocket example (Fluid Mechanics and Thermodynamics)
(Categories: A & B; Example Types: Demonstrations (experimental & mathematical) and
Sensing)
The example consists of having the students model a toy water/air rocket (purchased
at a toy store for about $2) using the principles of conservation of energy, Newton’s
second law of motion, the ideal gas law, and the phenomena associated with nozzle
flows.
Goal: Predict the height that a rocket would rise, given a certain amount of water and
air pressure inside the rocket. When the modeling is completed the students would
launch the rocket outside, and compare their observed results to the predicted results.
Conclusions: In this example the students are required to apply basic principles
learned in more than one class to a real example which they can physically observe.
This not only helps to clarify the basic principles but also serves to tie together different
courses. This type of example also teaches the students that the theories learned in class
have real world applications.
-5-

11. 3. Merry-Go-Round Example (Dynamics or Kinematics)
(Category: A & B; Example Types: Demonstrations and Sensing)
This example could be given as an out-of-class assignment or done as an in-class
assignment.
Goal: Illustrate the idea of relative motion and moving reference frames. The example
consists of having two students go to a play ground and have one student throw a ball
from a rotating merry-go-round to another student standing on the ground. The
students would then trade places and repeat the experiment and record their
observations of the flight path of the ball. To the student on the ground, the ball would
appear to travel in a straight line, as it does relative to the earth. To the student
rotating on the merry-go-round the ball would appear to move in a curved path away
from the student.
Conclusion: This example helps the students to get a physical feel for what is being
explained in class. Many engineering courses involve abstract concepts, and the
students have a hard time visualizing the engineering phenomenon. However, by
actually experiencing the phenomenon, students are better able to visualize and
understand the concept.
-6-

12. II. SHOW AND TELL
Reversing Student Roles
The “Show and Tell” technique is another form of the “Practical Examples” technique.
However, in this technique the role of the student is reversed to that of a teacher,
thereby changing their perspective of the problem. The basic premise of the "Show and
Tell" technique is that if one can explain a concept to someone else then he/she truly
understands the concept.
Scope
A typical "Show and Tell" project would require a student or a group of students to
explain a given theory or phenomenon to the rest of the class and also demonstrate a
physical example that helps visualize the phenomenon. Almost any example that you
can convincingly demonstrate in a classroom would be appropriate for a “Show and Tell”
project. However, it should be remembered that as with the case of the “Practical
Examples” technique, the concept to be explained by the students should be relatively
simple and straight forward. The purpose of this exercise is to challenge the students to
come up with a creative solution to the problem at hand without overwhelming them. In
order to avoid embarrassing situations and to ensure that the demonstrations are useful
to the entire class, it is also important for you to know before hand what the students
plan to present.
Example: Explain and demonstrate the Magnus effect
The magnus effect is a fluid dynamics phenomena observed when a projectile in flight
is spinning. The spinning projectile moves in a direction perpendicular to both it's main
path and rotation axis.
Goal: The student or group would be given the assignment to both explain and
demonstrate the magnus effect in class. The level of the expected explanation would
depend on the level of the course and the philosophy of the teaching assistant. This
particular example could be explained using potential flow theory (mathematically) or
more intuitively using the ideal of streamlines and Bernoulli's principle without
rigorous proof.
For the demonstration the students use whatever equipment or apparatus that they
can access. In the present case, one possible idea would be to use a cardboard tube from
-7-

13. a paper towel or toilet roll and a piece of string. The student would wrap the roll with
the string, stand on a chair holding the free end of the string and let go of the roll,
causing it to unwind from the string and move down. In addition to imparting a
downward velocity, the unwinding of the roll also causes the roll to spin. When the
string is completely unwound, the roll will tend to move perpendicular to the spin axis
(horizontal to the floor) as it falls to the floor. The horizontal direction of movement of
the roll will depend on the direction of rotation of the roll. The students could
demonstrate this by starting with the string wound in clockwise or anti-clockwise
directions. Other variations of this demonstration would be to bring in a ping pong ball
and paddle and demonstrate the magnus effect by hitting the ball with different types of
spin and watching the trajectory of the balls. The same idea could be demonstrated
outdoors by pitching a baseball.
Conclusions
Putting the students into the role of a teacher makes the students look deeper into
the assigned problem. The students will be forced to clarify their thinking and
understanding since they must explain to their peers the phenomena that they are
demonstrating. In searching for examples outside of class or for demonstrations that can
be performed in class, the students will be compelled to look for connections between
theory and practical application.
-8-

14. III. CASE STUDIES
Bringing “Real-Life” Scenarios into the Classroom
An engineering case study is an account of an actual engineering activity, event, or
problem containing some of the background and complexities actually encountered by a
practicing engineer. Since cases are accounts of “real-life” engineering activity, they help
the students to better relate theory to the “real-world”. Cases often involve concepts
from other disciplines like marketing and management, concepts that a practicing
engineer needs to know anyway. In addition, the case method promotes discussion in
class and feedback from the students.
Scope
Engineering case studies can be included at all levels of the engineering curriculum.
The hardest part of using case studies is finding cases that fit with the class material.
This however should not deter you from using the case method as there are over 200
cases in Wendt Library alone, not to mention many more texts on case studies.
Professors, other TAs, or contacts in industry are other great ways to find cases. With a
little work, it should not be too hard to find a good case for any class.
Strategies
Students are usually given written material regarding a case and asked to read it and
answer a series of questions pertaining to various aspects of the case. The students can
be required to work either individually or in groups. The following are some tips to
remember when using a case study:
• The case study questions may increase the amount of work the students
have to do outside of class. Care must be taken to balance this extra
workload against other homework assignments.
• When using case studies found in the library, do not stick to using the
questions given with the case. Generate new questions that directly fit
the topics covered in class.
• While the questions that are assigned form the basis of the discussion, be
prepared with other questions in order to guide the discussion.
• The goal of the case should be kept in mind at all times. Keep the
discussion from drifting away from this goal.
-9-

15. • Above all, be thoroughly prepared for the discussion. Poor preparation
will lead to frustration among the students.
Example: Design Change for a Walkway
The case study that follows was used in a design course taught in the College of
Engineering. The case helped students discuss how changes in a design caused during
manufacturing and construction can affect the safety of the overall design. The
students considered the following problem: The on-site engineers want to know if they
can change part of a design to ease construction. As head engineer, would you allow the
change, and why or why not? Pictures of the original design and changes in the design
are shown in figure 1.
Figure 1: Close-up of the change of the design of walkway.
The above material described the failure of the walkway in the Hyatt Regency Hotel.
The collapse occurred due to a shear failure of the beam when a large group gathered on
both the upper and lower walkways to watch a band playing in the courtyard below. In
the first design, the beam holds the weight of only one of the walkways. In the modified
design, the section of beam between the rods carries the weight of both walkways. The
failure occurred in this section of the beam. The TA did not disclose the effects of the
design modification while handing out the case materials; the students were simply
asked if they would allow the change and to include any calculations to support their
claims.
Conclusions
About a quarter of the class decided that they would allow the change while the rest
decided that they would not. However, the students who would not allow the change
produced a variety of answers, not all of which were close to the right answer. These
students who produced the right answers were asked to describe the failure mechanism
- 10 -

16. to the rest of the class. The TA graded the students’ work more on the amount of
thought put into the case rather than on getting close to the correct answer. The whole
exercise took only one full class period in addition to the time required for grading.
- 11 -

17. IV. GUIDED DESIGN PROJECTS
Introducing Practical Design Experience in Classrooms
Guided designs projects aim to bring practical design experience into the classroom.
Often conducted over a period of a semester, the projects give students an opportunity to
work in a team environment, apply theory learned in the classroom, and learn about
industrial design methodologies.
Scope
Guided design projects are appropriate for any level, but are often reserved for junior
and senior levels. As with the case method, choosing a project is typically the hardest
part. Using guided design projects usually requires a lot of preparation by the TA. One
of the best ways to have students appreciate the industrial design methodology is to
have them redesign existing systems or products.
Strategies
The following are some tips to remember when using a guided design project:
• Realize that the project is not as important as the thought processes that
go into determining a design. It is not important that the students
determine an optimum design. What is important, however, is that they
experience the design process.
• Starting before the semester, determine the scope of the projects and the
goals for the class. It is important that the scope of the project is
reasonable, and care must be taken to ensure that the students are not
overloaded.
• When possible, divide the design into sections. This spreads the work for
the students and the grading duties over the semester. Design teams of
two or three students are frequently used. This allows for in-depth
projects, reduces the grading load of the TA, and promotes interaction
among the students.
Example: Redesign of a parking garage gate
The following guided design project was used in a course on the mechanics of
materials. The goal of the project chosen for this class was to redesign a gate at a
parking garage so that it deflected on impact from a car. The gate is required to deflect
- 12 -

18. upon impact in order to avoid serious structural damage to the car. The project was
divided into three parts so that the work would be spread over the semester.
The first part involved brainstorming to determine the best methods to meet the
requirements. The students worked together in teams generating ideas. Then the entire
class spent part of a lecture discussing the various ideas. In the debate, the TA guided
the class towards a consensus about a design that would satisfy all requirements and yet
be easy to complete. The student assignment for the first part was to write up and hand
in a summary of their two best designs, the advantages and disadvantages of each, and
which design that they would choose and why.
The second part of the project involved determining the loads on the gate. This
required the students to synthesize knowledge from several courses that they had taken
earlier. Also, the TA had to devote extra time in class and during office hours to explain
methods for determining loads on a structure.
The final part of the project involved actual measurements and safety considerations.
Having determined the loads, the students proceeded to complete the final part of the
project where they determined the actual sizes of the various components used in the
design. As a last step, the students used failure theories discussed in class to ensure the
safety of the design.
Conclusions
The student response to this project was encouraging. They said that they enjoyed
the project despite the fact that they had to work harder. The students felt that the class
had a clear purpose and that the practical design aspect of the project improved their
understanding of the theoretical sections covered in class.
- 13 -

19. V. OPEN-ENDED LABS
Making Students Think Deeper
Open-ended laboratory classes can be broadly defined as classes where the students
are encouraged to design their own experiments or devise their own experimental
strategy, rather than required to follow a rigid set of experimental guidelines specified
elsewhere as in a lab manual, for example.
Scope
Laboratory classes can be made open-ended to varying degrees depending on a
number of factors including the autonomy that the TA has in changing the course
structure, the facilities available, and the degree of difficulty that the TA perceives to be
appropriate for the class. One can think of three general areas where a laboratory class
can be made more open-ended: 1) the experiment setup itself where the students
design an experimental setup to achieve certain goals, 2) the experimental design
where the students decide the scheme to be followed for data collection to achieve a
prescribed goal, given a certain experimental setup, and 3) data analysis and report
writing, where the students decide how the data is to be analyzed and reported.
Additionally, if none of the above options are feasible, the TA can consider making the
laboratory briefing session open-ended.
Open-ended Experiment Setup
A simple but effective example of an open-ended lab setup comes from a mechanics of
materials course. A few weeks into the semester, the TA divided the class into teams of
two or three students. As a part of a course project, the teams were required to
experimentally test the material properties of any household object that they were
interested in, write a report, and present their results to the rest of the class. The TA
initially offered suggestions regarding the different experiments (like tensile testing,
compression testing and bending tests) that could be run, different materials that could
be tested (like golf balls, beer cans, eggs, plastic bags, scotch tape and fishing line), while
also encouraging the students to exercise their creativity in finding test materials or
experiments. The teams were allowed complete freedom in choosing the equipment,
experimental parameters, and the data analysis methods. The TA mostly acted as a
consultant, offering hints and suggestions. As expected, the project presented many
- 14 -

20. challenges forcing the students to come up with creative means to solve the problem.
For example, how can the thickness of a sheet of plastic be measured?
Student Response: At the end of the semester the students felt satisfied that they
actually designed an experiment and performed “hands on” work. It was also satisfying
to the TA that the students were able to apply theoretical concepts to practical
applications, and develop a sense of appreciation for the difficulties involved in
designing and executing an experimental project.
Time Constraints: The biggest problem with this method is that it is time-intensive. For
safety reasons, the TA had to be in the lab at all times when students were testing
samples.
Open-Ended Experiment Design
As an example of the open-ended experiment design lab, consider the following
experimental setup available for performing heat transfer experiments in a junior level
chemical engineering laboratory. A large cylindrical tank equipped with a heating coil, a
stirrer with adjustable speed of rotation, baffles for efficient mixing, an external heat
exchanger through which fluid in the tank can be circulated, a pump to circulate fluid
through the external heat exchanger, a thermocouple at the bottom of the tank to
measure the temperature, a source of low-pressure steam and equipment to measure the
flow rates. More equipment such as additional thermocouples and insulation are
available in the lab stockroom.
In the standard lab format, the class is divided into groups and assigned specific
experiments to be performed by each group. The goals of the experiments, the
experimental procedure to be followed, the calculations to be performed, and the report
format (including specific quantities or observations to be reported) are discussed in
detail before the students perform the experiments. In an attempt to make the lab more
open-ended, one of the TAs decided to run the lab as follows:
1. Students were asked to briefly study the experimental setup and arrive
at an exhaustive list of experiments that could be performed. Clearly,
this required the students to recollect all the heat transfer theory that
they had studied and to involve themselves in collective brain-storming.
The TA merely coordinated the brain-storming exercise, and offered
hints and suggestions. For example, if additional thermocouples could be
rigged up, the temperature distribution in the tank could be measured.
- 15 -

21. The effect of evaporative losses could be determined if the tanks could be
covered with insulating material.
2. Next, the students were asked to briefly discuss the goals of each
experiment and rank them according to their usefulness with respect to
information content or time required to perform the experiment. For
example, the students concluded that the experiment to study the effect
of steam was more important than the experiment that would measure
the heating effect of the pump. Therefore, they decided that they would
perform the latter experiment only if time permitted.
3. Subsequently, the students were asked to organize themselves into
groups and select a subset of the experiments to work on. The groups
were asked to briefly sketch the details of each particular experiment
such as the flow rate or stirrer speed to be used, or making sure the right
parameters are changed during the experiment. The TA acted as a
consultant, reviewing the experimental plans proposed by each group
and offering suggestions. After a briefing about general safety
procedures the groups proceeded with the experiments.
4. Finally, the students were required to turn in group reports in whatever
format that they thought was appropriate. In addition, each group was
required to briefly present their results to the class the following week.
Student feedback regarding the open-ended lab was encouraging. Most of the students
enjoyed the freedom they had in designing the experiments, and the opportunity to
exercise their creativity. Some students were initially uncomfortable about the lack of
direction and specific instructions, while a few expressed a preference for the standard
lab protocol.
TA Response: From the viewpoint of the TA, the open-ended lab was a big success. The
lab format forced the students to think deeply about the theoretical concepts that were
to be applied, to generate ideas and evaluate them, and to design and successfully
execute an experimental plan.
Open-Ended Data Analysis and Report Writing
Students in most lab classes are given detailed instructions regarding data analysis,
and report formats such as specific quantities to be reported, and specific figures to be
plotted. This traditional approach reduces the workload of the TAs. They have to spend
less time explaining data analysis procedures. Grading lab reports with a standard set of
protocols is easier. However, it does not allow the students to think deeply about the
material or give them an opportunity to express their creativity.
- 16 -

22. In an effort to make the lab report writing process more open-ended, a COE TA
adopted the following strategy:
1. Hand out very brief information about expected report formats. Suggest
possible calculations, tables, and figures to be presented.
2. Have the students work on a rough draft or outline of the report and
discuss their report outline with the TA during office hours.
3. Suggest modifications and have the students turn in the final draft
during lab the following week.
Student response: As can be easily guessed, the initial student response was marked by
frustration and pessimism, for the simple fact that they hadn’t done anything like this
before. The students’ attempts at designing their own reports were half-hearted, and the
students required a lot of hand-holding. However, as time progressed, they grew more
confident and came to believe that they were capable of producing good quality work.
TA Response: The open-ended report writing format forced the students to think about
different report writing schemes and evaluate them for their effectiveness in
communicating the results. At the technical level, it forced the students to think deeply
about the data analysis procedures and the interpretation of the results, in contrast to
merely churning out numbers using a calculator.
Caveats: It should be noted that making the lab report writing process open-ended does
not imply a “hands off” policy. Indeed, a TA stands to be perceived by the students as
being uncooperative, or more damagingly, as trying to shirk his or her responsibilities, if
such a policy were to be adopted. It is important for the TA to provide meaningful and
constructive feedback to the students, lest the students get discouraged and frustrated
with the system.
Open-Ended Laboratory Briefing Sessions
Often it is not feasible for the TA to make a lab class open-ended. In this case, the
goal of forcing the students to think deeply about the application of theoretical concepts
and the design of the experimental plan can be achieved by making the laboratory
lecture open-ended. The thought process that goes into designing an experiment can be
simulated in a lecture by adopting the following strategy:
1. The TA introduces the goal of the experiment and organizes a brain-
storming session by posing questions such as, “The goal of today’s
- 17 -

23. experiment is to measure the viscosity of glycerol as a function of
temperature. Can you suggest a few ways of doing this and explain the
operating principle ?” The TA then collates the ideas generated, has the
students discuss the pros and cons. At this point, the TA directs the
students’ attention on the technique prescribed in the syllabus by saying,
“Now that we have discussed the different possible methods, let us focus
on the method that we will be using today, the capillary viscometry
technique”.
2. In the next stage of the lecture, the TA generates a discussion of the
details of the experimental apparatus and the experimental technique by
posing questions such as: “Why is the capillary designed in such a
fashion”, “How is the pressure drop problem addressed in this design”,
“Why and how can we calibrate the viscometers”, “How can we maintain
the viscometers at different temperatures”, “How should we process the
data”, “What quantities do we plot in order to obtain the viscosity”.
3. Finally, after a brief recap of the important aspects of the experiment the
students are allowed to proceed with conducting the experiment.
Student response: Most of the students agree that this technique “makes them think”
and “helps them appreciate the science behind the experiments”. It also calls for a lot of
class participation by the students. Occasionally, if the call for a discussion does not
evoke sufficient responses, the TA may be required to call on students to answer
questions or generate ideas. It should be remembered that some students dislike being
called on to answer questions in class. Asking students to share ideas with a partner or
in small groups first, generates more ideas and makes the students feel more confident
about sharing their ideas.
Time Constraints: Organizing brain-storming sessions in lieu of the standard briefing
sessions is bound to cut into the time available for conducting the experiments.
However, the pay-off in terms of the improved students’ comprehension of the “science
behind the experiments” makes the open-ended lecture technique well worth the
investment in time.
- 18 -

24. VI. THE FLOWCHART TECHNIQUE
Organizing the Flow of Thought
The technique of flowcharting, as applied to a classroom scenario, is a tool for
precisely and concisely representing the flow of information among various stages in the
development of a theoretical concept or in the formulation or analysis of an engineering
problem. Flowcharts are a tool to organize the flow of logic and thought in a classroom,
much in the way that flowcharts help in presenting the flow of materials between
various units of an industrial process.
Scope
Flowcharts are one of the most indispensable tools that practicing engineers use to
organize large amounts of information. One cannot imagine even the smallest unit of a
manufacturing concern being constructed or operated without the aid of flowcharts.
Flowcharts can be equally useful and effective in conveying and presenting engineering
information in a classroom or laboratory.
Flowcharts in Laboratory Instruction
Consider the following experiment in a junior level chemical engineering laboratory
to determine the viscosity of a solution of glycerol in water using a capillary viscometer.
In this method, a known volume of fluid is allowed to flow through a capillary of known
dimensions, and the time taken for the fluid to flow a certain distance is related to the
viscosity using a proportionality constant called the viscometer constant.
One of the main steps in this experiment is to determine the viscometer constant by
running the experiment with a fluid of known viscosity such as sucrose. The sucrose
solutions are prepared by dissolving crystals of sucrose in water and, therefore, have to
be analyzed for the sucrose concentration. An easy method for determining the
concentration of sucrose is to measure its density and convert it to a concentration using
published correlations. The density in turn is measured using a device called the
pycnometer. The pycnometer is a carefully constructed volumetric flask which allows
the weight of a constant volume of fluid to be measured and related to the density. The
volume of the pycnometer itself needs to be calibrated using a fluid of known density
such as distilled water.
- 19 -

25. As mentioned earlier, the viscosity of sucrose can be interpolated from published
tables once the density is known. This in turn allows the viscometer constant, and
subsequently the viscosity of glycerol (the goal of the experiment) to be determined.
Finally, as a check of consistency, the experimentally determined viscosity of glycerol is
compared with published values. The published values of viscosity can be interpolated
from tables if the concentration is known. The concentration of glycerol is determined
along the same lines as that for sucrose.
As an exercise, imagine that you are a student who has just been briefed about these
experiments in the standard lecture format. Now, try to recall the sequence of steps
involved in the experiment. As a subsequent exercise, take a look at the flow chart in
figure 2 for 5-10 minutes and try to recall the sequence of steps in the experiment.
Which method is more efficient in communicating the flow of thought and logic in the
experiment?!
Student response: The students strongly agreed that the flow chart technique was
more effective in communicating the overall goals of the experiment. In their words,
they could now “see more clearly where they were headed”. The students felt more
confident doing the experiments since they had a “road map” in front of them.
Additionally, the students found that the flowcharts greatly helped them subsequently
while analyzing the data and writing the lab report.
Comments: It is possibly better to derive the flowchart on the chalk board during the
lab briefing session and distribute previously prepared ones at the end of the class. This
allows the students to “see where the TA is coming from” or understand why the
flowchart looks the way it does. Better yet, the students can be required to create their
own flowcharts during the briefing sessions.
Flowcharts in Lectures
Students often express concerns about not being able to understand where a lecture
is headed or how the concepts taught in previous lectures relate to the concepts being
presented in the current lecture. Flowcharts can be used effectively to address this
concern. Flowcharts are very useful in emphasizing the flow of thought in a
presentation, or in relating previously covered topics to the present material. One COE
TA has made flowcharts an integral part of every lecture. The lecture starts off with the
TA partitioning the chalkboard into two sections; one for presenting the lecture and the
other for developing a flowchart as the lecture progresses. At the start of the lecture the
flowchart consists of a single block where the goals of the lecture are clearly spelled out.
- 20 -

26. As each concept is presented and the lecture proceeds towards the goals, the flowchart is
updated by adding more blocks to indicate the significant concepts and arrows
connecting the blocks to indicate the flow of thought. Since the flowchart always stays in
a corner of the chalkboard, the students are constantly reminded of the goals of the
lecture and the concepts that have been covered in the lecture. The flowchart, which is
essentially a summary of the lecture, also makes it easy for the TA to recap the lecture
at the end of the class. For the same reason, flowcharts come in handy for students to
review lecture material before exams.
Student Use of Flowcharts to Tackle Engineering Problems
Flowcharts can be especially helpful in solving open-ended problems. Students can
prepare flowcharts alone or in groups to show processes and help solve open-ended
problems. A new module to help students create flowcharts will be available for 1995-96
from the Technical Communication Division, Department of Engineering Professional
Development. The module was developed with support from IBM.
- 21 -

27. Figure 2. Flowchart showing the sequence of steps in the determination of the viscosity
of glycerol.
- 22 -

28. VII. OPEN-ENDED QUIZZES
Moving Students Away From Memorization
The open-ended quiz is intended to stimulate students' creativity and to help students
to think deeply about the material covered in lectures. In contrast, straightforward
“Given this, calculate that” or “Plug and chug” type of quizzes merely encourage
students to memorize equations and formulae.
Scope
As in the case of the other open-ended teaching methods, the scope of the open-ended
quiz method is only limited by the creativity of the instructor and the constraints
imposed by the system.
Examples
An interesting example of the open-ended quiz method comes from Dr. Felder,
professor of chemical engineering at the North Carolina State University (reference his
article). For one of the mid-semester quizzes in a Graduate level course in chemical
reactor design, Professor Felder1 gave a five-week take-home exam that asked students
to make up and solve a final examination for the course! The students were told that if
they produced a straightforward “Given this and that, calculate that”, they would
receive a minimum passing grade, and that to receive more credit, they would have to
demonstrate a deeper understanding of the material, the ability to apply techniques
from other disciplines, and the ability to evaluate the value of a design, product, or
system.
The above example, while probably one of the most open-ended exercises that can be
thought of, is also time consuming. The goal of making students think deeply about the
material can be achieved even in a 15 minute quiz. For example, students can be asked
to solve problems that do not specify all the information that is needed to arrive at the
answer. The students are then forced to think about what other information may be
needed, and how they might go about obtaining the needed information. Some other
variants of open-ended questions are:
1 Felder, R. M. (1987, January). On creating creative engineers. Engineering Education, 77(4),
222-227.
- 23 -

29. 1. Make up a problem which has more information than what is needed to
solve the problem. The students must now think about what pieces of
information are critical to solving the problem at hand.
2. Make up a problem that has the students come up with a list of different
ways to accomplish a specific task. For example, come up with different
ways to measure the flow rate of water in a pipe. The discussion of the
feasibility of various methods will help students acquire the ability to
critically evaluate different solutions.
3. Have the students assume that they are teaching the class and come up
with creative ways to teach that class. In addition to helping the
students think creatively, this also provides useful feedback about the
direction that the students would like the TA to take.
4. Have the students come up with creative quiz questions.
5. Have students come up with different analogies to teach difficult
technical concepts.
6. Assign or make up a problem that requires the students to use their
engineering judgment.
- 24 -

30. VIII. BRAINSTORMING
Encouraging Creativity
The brainstorming technique is widely used in industry and academia to encourage
participants to generate ideas in an unhindered manner. In an academic context,
brainstorming encourages students to participate actively in idea-generation exercises
and experience benefits of a multi-dimensional approach to analyzing problems or
solutions.
Scope
The brainstorming technique is applicable to all levels of the engineering curriculum
and to all teaching scenarios - labs, lectures or discussion sections. It is especially useful
in design courses since it calls for a multiple-answer-multiple-dimension methodology
rather than the usual single-answer approach to problems. The brainstorming technique
can be implemented in a number of different ways as follows:
1. Structured: The whole class is given a topic to discuss and each student is called
upon to contribute an idea. The advantage of this method is that all students participate
and the more vocal students tend not to dominate the discussions. The disadvantage is
that the discussions usually do not flow freely as in an unstructured session, and can
make some students feel pressured and uncomfortable.
2. Unstructured: Students are allowed to contribute ideas as and when they think of
them. This approach allows for a freer flow of ideas and a more relaxed environment.
The drawbacks to this approach are that it can lead to the students not responding at all
or to a few students dominating the discussions.
3. Group: This is a structured approach except that the class is broken into small
groups and each group presents its ideas after an allotted amount of time. The
advantage of this method is that the students are likely to be more at ease and willing to
express their ideas. This also promotes synergy and communication among the
students. One obvious drawback to this method is that it more time-intensive than the
other two methods.
Guidelines
The following guidelines should be followed with any of the above methods:
- 25 -

31. • Make sure that everyone agrees on the question or issue being
brainstormed. Write it down on a chalkboard, for example, or give
handouts.
• Never criticize students’ ideas or allow students to criticize each other.
• Do not allow students to reject ideas initially. Ideas should not be weeded
out until the brainstorming is completed. This keeps the solution path
from becoming prematurely narrowed.
• Write every idea down. Use a flip chart, blackboard, overheads, post-it
notes, or other visual methods.
• Use the words of the speaker when recording; do not interpret.
Examples of Brainstorming Applications
1. Analysis of Lab Equipment
(Example from ME 370, "Energy Systems Laboratory”, Senior level ME lab course)
In the ME 370 "Energy Systems Laboratory”, Senior level ME lab course, students
run experiments using equipment that have complete computerized data acquisition
systems. While data acquisition systems allow the students to collect a large amount of
precise data, they also reduce the creativity and thought that is required of the students
to run the experiments. To better involve the students in the experiments and to help
them think more deeply about the experimental setup, the TA initiated an impromptu
brainstorming session on the instrumentation for an Ingersol Rand double-acting
reciprocating air compressor. Specifically, the TA asked the students to consider the
following questions:
1. What are the important performance parameters needed to characterize
the performance of the compressor?
2. What measurements are necessary to determine or measure the
important performance parameters?
3. What instrumentation could be used to take the necessary
measurements?
The students initially considered the first question and suggested several ideas. The
TA then initiated a discussion of the generated ideas and guided the class towards a
consensus about the correct set of parameters. The class then moved on to consider the
second and third questions using the same brainstorming format. After discussing the
final question the class proceeded to review the actual equipment instrumentation and
compare it with the instrumentation scheme that they had arrived at.
- 26 -

32. The entire brainstorming exercise required only 45 minutes. It served as a review for
the students, and proved to be a very interesting learning experience for both the
students and the instructor. The students came away with an appreciation for the
amount of detail and planning that goes into designing experiments.
2. Optimal Design of a Journal Bearing
(Example from ME 748, “Optimal Design”, Taught by Professor Seireg)
The critical step in optimal design is in determining the proper objective function that
is to be minimized or maximized. The objective function is an equation in the
independent variables and design parameters of the problem. The objective function is
minimized or maximized by varying the independent parameters within the given
constraints while keeping the design parameters constant.
In the following example, Professor Seireg organized a brainstorming session on the
optimal design of a journal bearing. The independent variables, the design parameters
and, the constraints imposed on the design are summarized in the table below:
Independent Variables Length of the bearing - L
(To be optimized) Radius of the bearing - R
Radial clearance between
journal and bearing - C
Design Parameters Load to be supported - F
(To be kept constant) Speed (or speed range) bearing
must operate at - N
Constraints on Design Minimum oil film thickness
allowable - hmin
(Physical or other limitations)
Maximum oil temperature
allowable - Tmax
Bearing stability criteria
The goal of the brainstorming session was to determine the proper objective function
U = f(L, R, C; F, N) which can be minimized or maximized by varying the three
independent variables L, R and C. A summary of the class responses are given below:
• Minimize the oil flow rate (Q) required for lubrication
• Minimize the maximum temperature rise of the bearing (∆T)
- 27 -

33. • Minimize the overall volume of the bearing (V)
• Minimize frictional losses encountered while running the bearing. The frictional
losses are equivalent to the energy generated in the oil (= Q.∆T)
All of the above solutions were on the right track, but were not complete. At first
glance, it appears that the minimization of the friction losses is the best strategy since
the function of a bearing is to minimize frictional losses. However, Professor Seireg
showed that the best objective function was one that combined two of the four factors
suggested by the class. The objective function U = Q + K.∆T, where K is an empirical
constant, accounts for the costs associated with pumping the oil and cooling hot oil back
to the original temperature.
It can be seen from the description of the problem that the task of determining the
optimal design of a journal bearing is not trivial. There are a number of variables and
parameters that enter the calculations, and it not very obvious what the best objective
function is. However, the process of brainstorming allowed the students to discuss
various solutions and understand the pros and cons of each approach.
Conclusion
Brainstorming provides a forum for students to express creative ideas. It encourages
students to be open-minded when analyzing problems, an attitude that is required for
solving most real-life engineering problems which have multiple solutions.
- 28 -

34. IX. QUESTION-AND-ANSWER METHOD
Encouraging Student Participation
The goal of the question-and-answer method is to draw students into active
participation in teaching and learning processes. The technique also encourages
students to move beyond memorization to higher levels of learning that require
clarification, expansion, generalization, and inference. Often students are conditioned to
simply sit in class, take notes and then study and learn the information on their own.
With the question-and-answer methodology, the students can learn in real-time, as they
are being taught, which helps them understand and integrate the material better.
Scope
The question-and-answer methodology is useful in any teaching environment. The
approach used in applying this methodology is of course influenced by the course being
taught and the teaching style of the instructor. This methodology can be used to
structure an entire class, where the class consists entirely of a question-and-answer
session. This approach is especially useful for discussion sections and exam reviews.
Effective and efficient use of this method requires that you have a thorough
understanding of the material being discussed. It also requires that you devote time and
thought into devising a set of appropriate questions for use during a presentation. It is a
good strategy for you to anticipate student responses to your questions so that you can
stay “a step ahead” of the students.
Goals
Thoughtful questioning attempts to achieve one or more of the following goals:
• Stimulate analytical thought
• Diagnose student difficulties
• Determine progress toward specific goals
• Motivate students
• Clarify and expand concepts
• Encourage new appreciation and attitudes
- 29 -

35. • Give specific direction to thinking
• Relate cause to effect
• Encourage student self-evaluation
• Encourage the application of concepts
• To arouse interest and curiosity
• To focus attention on an issue
• Promote thought and understanding of ideas
• Manage or remind students of a procedure
Guidelines
A well-planned list of questions is only the first step towards achieving the above
goals. Merely posing questions is not enough to motivate students to move to higher
levels of learning. The following guidelines may be useful in conducting successful
question-and-answer sessions:
• Probe deeper after a student answers a question.
• Structure the follow-up questions ahead of time. It is a good idea to write
down such questions on note cards or the margins of the lecture notes.
• Use “who”, “what”, “when”, and “where” questions to check information
possessed by students. For higher thought levels, use “why” and “how”
questions.
• Push students’ responses to “why” and “how” questions to higher levels of
thought by asking for more explanation.
• When using questions with individuals, state the question, pause, then
call on a student to answer. This leads all students to listen to the
question. The pause provides time to think -- respect that period of
silence.
• Summarize complicated or ambiguous answers to questions.
• Do not embarrass a student by repeatedly asking questions the student
is unable to answer.
• Be reasonably lavish in the use of “good”, or other words of praise to
students who give correct answers. Avoid making any negative
comments after an incorrect answer -- this is sure to ensure low response
on future questioning.
- 30 -

36. • Allow students the opportunity to formulate questions in response to
answers from you or other students.
• Never use questions as a form of punishment. Do not call on a student
just because they forgot their homework, never volunteers, disrupts the
class or provides a careless response.
- 31 -

37. X. SOFTWARE
Increasing Teaching Efficiency
Software tools are widely used today in the classroom and are proving to be very
effective teaching aids. One of the benefits of software tools is that they offer a means for
visualization of abstract concepts and ideas. If used properly software tools can improve
teaching efficiency in many instances. As a teaching tool, computer software can provide
a new way to link abstract concepts with tangible visualizations. Specialized computer
software offers students the option of self-learning and can also be instrumental in
motivating them to learn abstract engineering concepts.
Scope
A variety of software options for classroom use are currently available. These range
from software for improving communication with students to specialized software for
teaching an entire course. The Computer Aided Engineering (CAE) Center in the
College of Engineering and the Department of Information Technology (DoIT) at UW-
Madison have access to numerous teaching-related software. Any interested TA should
contact these units for further information. The CAE also maintains an on-line help
system which can be accessed from CAE computers (by typing “caehelp”), from “gopher”,
or from “Wisc-Info”. Meanwhile the TA may consider using the following three types of
software in the classroom:
1. Email: Electronic mail offers a way for increased two-way communication between
the TA and the students. Mailing lists for distribution of e-mail to an entire class are
now available from the CAE. Effective use of e-mail requires that the students and the
TA be diligent about checking their mail and responding to questions. One pitfall with
e-mail is the tendency to use it as a substitute for office hours and direct contact.
Although this approach may seem to be efficient on the surface, it tends to distance the
TA from the students and discourages interaction.
2. Presentation: Currently available word processors like Word, WordPerfect and
AMI Pro and presentation software like Powerpoint, Persuasion and Harvard Graphics
offer very powerful presentation capabilities not available only a few years ago. This
means that the TA can potentially present more information in a clearer manner and in
lesser time. The combination of new presentation software and equipment like optical
scanners (available at CAE) gives the TA the ability to select and condense material
- 32 -

38. from a wide variety of sources and present it in a convenient and professional manner.
The following caveat is in order when using presentation software:
• Avoid shifting the emphasis of the presentation from the content to the
appearance. It must be remembered that in engineering function should
precede form.
3. Modeling and Analysis: Software programs for modeling and analysis of large
amounts of data or complex systems are now widely available. One such program used
extensively for lecture and laboratory courses in the Mechanical Engineering
department is Engineering Equation Solver (EES) developed by Professor S. Klein. The
advantage to EES and other mathematical analysis software such as Mathcad and
Matlab is that the instructor can assign homework problems that are more in-depth in
nature. These programs allow students to model systems and see the effect of varying
system parameters, thereby, aiding them in developing a deeper understanding of the
theory. The advanced computing capabilities of these programs also allow the TA to
demonstrate complicated phenomena in the classroom. The following are some tips to
keep in mind while using such software:
• Completely solve problems before assigning them for homework. Ensure
that the problem is reasonable and can be completed by the students in a
reasonable amount of time. It is easy to design problems that seem
simple on the surface but are actually quite complicated.
• Αvoid assigning problems that fit the software. The goal is to solve
problems that are relevant to the course and seek software help to do so.
Example of Software Use in a Laboratory Class
The following example is from a junior level ECE laboratory course in
electromechanical power conversion. The course is intended to teach the basic principles
of electromechanical power conversion and power electronics through the use of student-
run experiments. The students are given the lab handout detailing the procedures and
goals of the experiment. After briefly reading the handout, the students are required to
setup the experiment and acquire data, process the data, and analyze the results. The
experiments involve the use of a number of electronic measuring instruments such as
LCR meters (for measuring inductance), oscilloscopes, electric power supplies, function
generators, and other related instruments. However, a majority of the students taking
the course are from Mechanical Engineering who are typically unfamiliar with the
detailed functions and use of these instruments. Quite naturally, the students have been
unsure about proceeding with the experiments because of this reason.
- 33 -

39. Recently a user-friendly software module was developed by the TAs under the
supervision of Professor R. D. Lorenz in the ME department. The module guides the
students through the process of setting up the experiments and collecting the data.
Using a graphical approach, the module guides the students in a step-by-step fashion
through all phases of the experiment including connecting the equipment, assembling
circuits, setting parameters, and collecting the data. The module also gives the students
the option of learning more about the concepts behind the experiments as they proceed
with collecting information. In addition, the software eliminates the drudgery of
recording and manipulating the data since the data collected is now available on the
computer in a ready-to-use format.
Conclusions
As a result of the new software students feel more confident, and less frustrated,
about proceeding with the lab experiments. The software use makes for more efficient
learning since much of the hesitation, drudgery and busy work is eliminated, leaving
more time for understanding the concepts behind the experiments.
- 34 -

40. XI. Conclusion: Teaching Improvement
Monitoring Your Progress
Just as this Handbook will continue to evolve, so will your teaching style continue to
evolve as you strive to match the learning styles of your students. We hope that this
Handbook has sparked your creativity and provided you a basic resource from which to
share teaching strategies that have worked for others. Developing a variety of teaching
strategies will help you and your students build a learning community.
To develop this variety of strategies that will work for you and your students, we
suggest that you monitor your progress. The following framework is one that you could
use to document strategies you use and assess how they work. The framework follows
the familiar "plan, do, check, act cycle" which is a continuous improvement process used
in business, industry, government, and higher education.
Plan: Concept - The concept that you plan to teach
Strategy - The teaching strategy that you plan to use
Date - The day you plan to use the strategy
Materials Needed - The teaching materials that you will need
Time Needed - Plan your teaching activity so that you can accomplish all
your goals
Feedback - Decide on a strategy to obtain student feedback. Consider fast
feedback, written reports and observing students’ reactions
Do:Execute your plan
Check: Review student evaluations
Act: Decide on what you would do next time. Stick with the strategy? Change?
We thank all those who provide material for this Handbook and look forward to
getting your suggestions, examples, and references. Remember, you are a significant
player in achieving "education excellence." Together, as students and teachers, we can
build a learning community that will make a difference in society.
- 35 -

41. XII. FAST FEEDBACK FORM
Contributing Your Ideas!
We hope you found this handbook useful. Your suggestions will help us revise this handbook
periodically. We would appreciate it if you could complete the following questionnaire.
1. This handbook is easy to read: 5 4 3 2 1
2. The handbook contains useful material 5 4 3 2 1
3. Comments and Suggestions for improvements:
(fold here)
4. I’d like to have the following teaching strategy added to the handbook:
Strategy:
Course:
Concept:
Description:
(Optional) Name:__________________________________ Department: _____________
e-mail: ______________________________________
TA _______ Faculty _______ Other: _____________________________
(fold here)
Please return to: Campus Mail
Office of the Associate Dean for Academic Affairs
Attn: TA Fellows Project
College of Engineering
University of Wisconsin
Room 2640 Engineering Hall
Madison, WI 53706
Phone: (608) 262-4819
- 36 -