SlideShare una empresa de Scribd logo
1 de 2
Descargar para leer sin conexión
NOTES:
•	 If using a non-Leviton Programmer/Remote, refer to the
Programmer/Remote instruction sheet.
•	 1-scene controllers included into a Z-Wave®
network must be
updated after you have included all other devices.
•	 If using the VRCPG's Install Checklist feature, go directly to Step C.
A)	 If using a Leviton Z-Wave®
Programmer/Remote, Cat. No. VRCPG,
press the Menu button and scroll down to System Setup. Press
the center button to select System Setup Menu. Choose Advanced
Settings. Press the center button to select Network. Press the center
button to <Include Node>.
B)	 If using VRCPG Programmer/Remote, you will be prompted to place
1-scene controller into programming mode.
C)	 To access Program mode, engage the air-gap
switch by gently pressing the top of the push
pad until the bottom lifts completely out of the
frame and a click is heard (refer to figure).
Wait 5 seconds and then press the push pad
back into the frame and hold push pad until
the LED turns Amber. Release the push pad
and the LED should blink Amber. You are now
in Programming mode.
	 NOTE: If the LED on the 1-scene controller
turns solid Red while including, there has
been a communication error.
D)	 While standing close to the 1-scene controller
(approximately 2-5 ft.), press the center
button on the Programmer/Remote to
<Include> device in the network. NOTE: Only
one device may be included at any time.
E)	 The VRCPG Programmer/Remote will assign a Home ID, Node ID,
and Name for this device.
	 NOTE: This information will be stored in the Programmer/Remote to
be used for future reference.
	 NOTE: You may edit the name of this device at this time.
F)	 The 1-scene controller is now installed in the network.
WARNINGS AND CAUTIONS:
•	 ON/OFF LED for 2-way status reporting.
•	 To be installed and/or used in accordance with appropriate electrical codes and regulations.
•	 If you are unsure about any part of these instructions, consult a qualified electrician.
•	 Vizia RF +TM
VRCS1 1-Scene Controller does not control the load, but provides remote operation with Vizia RF +TM
switches.
•	 Recommended minimum wall box depth is 2-1/2".
WARNINGS AND CAUTIONS:
•   No traveler wires are needed. Remote controls via radio frequency (RF) technology.
•	 Can call one (1) scene ON/OFF or area ON/OFF with advanced Programmer/Remote (see VRCPG).
•	 For a complete set-up, a controller supporting the advanced Z-Wave® scene features is needed, such as the advanced Programming Remote (VRCPG).
•	 Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.
•	 Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.
1-Scene Controller/
Virtual Matching Switch Remote
Cat. No. VRCS1
120VAC, 60Hz
Installation Instructions
DI-000-VRCS1-02B
Tools needed to install your 1-Scene Controller
Slotted/Phillips Screwdriver	 Electrical Tape	 Pliers	 	
Pencil	 	 	 Cutters	 	 Ruler
Changing the color of your 1-Scene Controller:
Your device may include color options. To change color of the face,
proceed as follows:
Line up tabs
and press in
sides one at a
time to attach
Push in
side at tab
to release
INSTALLING YOUR 1-SCENE CONTROLLER
NOTE: Use check boxes           when Steps are completed.
WARNING: TO AVOID FIRE, SHOCK OR DEATH; TURN
OFF POWER at circuit breaker or fuse and test that power is off
before wiring!
Step 1
Step 3 Preparing and connecting wires:
This 1-scene controller can be wired using side wire terminal
screws or through backwire openings. Choose appropriate wire
stripping specifications accordingly.
•	 Make sure that the ends of the wires from the wall box are	
straight (cut if necessary).
5/8"
(1.6 cm)
Strip Gage
(measure bare
wire here)Cut
(if necessary)
Side Wire Connection
Side wire terminals accept #14
AWG solid wire copper only.
Back Wire (either hole may be used)
Back wire openings use #14-12 AWG
solid wire copper only.
WIRING 1-SCENE CONTROLLER:
Connect wires per WIRING DIAGRAM as follows:
•	 Green or bare copper wire in wall box to Green terminal screw.
•	 Line Hot wall box wire to terminal screw marked "BK".
•	 Line Neutral wall box wire to terminal screw marked "WH".
•	 Proceed to Step 5.
•	 Position all wires to provide room in
outlet wall box for device.
•	 Ensure that the word “TOP” is facing up
on device strap.
•	 Partially screw in mounting screws in
wall box mounting holes.
	 NOTE: Dress wires
with a bend as
shown in diagram
in order to relieve
stress when
mounting device.
•	 Restore power at circuit breaker or fuse.
•	 LED should turn ON.
	 If LED does not turn ON, refer to the
TROUBLESHOOTING section.
Testing your 1-Scene Controller prior to
mounting in wall box:
Step 5
Gently press top
of push pad
Wiring Application:
Hot (Black)
Neutral (White)
Line
120VAC, 60Hz
BKWH
Green
Ground
1-Scene Controller
Step 4
2
3
1
2
1. 	Line (Hot)
2. 	Neutral
3. 	Ground
Identifying your wiring application (most common):
NOTE: If the wiring in your wall box does not resemble this
configuration, consult a qualified electrician.
Step 2
INTRODUCTION
Leviton’s Vizia RF +TM
components are designed to communicate
with each other via Radio Frequency (RF) to provide remote control
of your lighting. Using RF technology allows Leviton to provide the
greatest signal integrity possible. Each module in Leviton’s Vizia RF +TM
component line is a Z-Wave®
enabled device. In a Z-Wave®
network,
each device is designed to act as a router. These routers will re-transmit
the RF signal from one device to another until the intended device
is reached. This ensures that the signal is received by its intended
device by routing the signal around obstacles and radio dead spots.
This 1-Scene controller is meant to control special scene enabled
Z-Wave®
products. To control groups of devices that are mixed or do
not support scene command class use the Leviton 1-Zone Controller
(VRCZ1). Setting up this device requires specific advanced controller
functionalities, your controller must be able to associate device to groups
and must be able to control the scene controller configuration commands
such as the advanced Programming Remote (VRCPG).
•	 This is a Z-Wave®
Controller
• 	 3-way or 4-way control without traveler wires
• 	 Can call 1 scene
• 	 ON/OFF LED
• 	 Two way communication
• 	 RF reliability
• 	 Ease of installation – No new wiring
• 	 Compatible with other Z-Wave®
enabled devices
FEATURES
Including 1-Scene Controller into Z-Wave®
Network:
Step 8
Restore Power:
Restore power at circuit breaker or fuse.
Installation is complete.
1-Scene Controller Mounting:
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.
Step 6
Installation may now be completed by
tightening mounting screws into wall box.
Attach wallplate.
Step 7
Device Association:
After inclusion process, you must associate the devices
to the controllers. Refer to the Primary Programmer/
Remote instruction sheet for complete details.
A)	 If using a Leviton Z-Wave®
Programmer/Remote, Cat. No. VRCPG,
press the Menu button and scroll down to System Setup. Press
the center button to select System Setup Menu. Choose Advanced
Settings. Press the center button to select Network. Scroll down to
<Exclude Node> and press the center button.
B)	 If using VRCPG Programmer/Remote, you will be prompted to place
1-scene controller into programming mode.
C)	 To access Program mode, engage the air-gap switch by gently
pressing the top of the push pad until the bottom lifts completely out
of the frame and a click is heard (refer to figure). Wait 5 seconds
and then press the push pad back into the frame and hold push
pad until the LED turns Amber. Release the push pad and the LED
should blink Amber. You are now in Programming mode.
	 NOTE: If the LED on the 1-scene controller turns solid Red while
excluding, there has been a communication error.
D)	 While standing close to the 1-scene controller (approximately 2-5 ft.),
press the center button to <Exclude> device from the network.
Factory Default:
If your 1-scene controller is not responding, or you are unable to control
it after you have tried to Include/Exclude it multiple times, it may be
necessary to reset the 1-scene controller to its original factory settings.
To accomplish this, proceed as follows:
•	 On the 1-scene controller, engage the air-gap
switch by gently pressing the top of the push
pad until the bottom lifts completely out of the
frame and a click is heard (refer to figure). Wait
5 seconds and then press the push pad back into
the frame and hold push pad until the locator LED
turns Amber and then flashes Red. Release the
push pad. The 1-scene controller is now reset.
Once the controller is reset, it will be necessary to
Re-Include it to a network before it can be used.
CAUTION: SETTING A DEVICE TO A FACTORY
DEFAULT DOES NOT EXCLUDE THAT DEVICE
FROM A NETWORK. THE EXCLUSION
PROCEDURE MUST STILL BE FOLLOWED TO
REMOVE THE DEVICE FROM THE PRIMARY
PROGRAMMER/REMOTE'S INFORMATION TABLE. FAILURE TO DO
SO MAY RESULT IN SYSTEM THAT IS SLOW TO RESPOND, OR MAY
FAIL TO RESPOND TO SOME DEVICES.
DI-000-VRCS1-02B© 2009 Leviton Mfg. Co., Inc.
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement,
at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, New York 11747. This warranty excludes and there is disclaimed liability for labor
for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied
warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental,
indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
Programmer/Remote
Cat. No. VRCPG
NOTE: Programmer/Remote must be
in close proximity to 1-scene controller
when including in the network.
Step 9 Excluding 1-Scene Controller from
Z-Wave®
Network:
For additional information, contact Leviton’s
Techline at 1-800-824-3005 or visit Leviton’s
website at www.ViziaRFplus.com
Protected under U.S. Patent Number 6,388,399 and patents pending and
licensed under U.S. Patents Numbers 5,905,442, and 5,982,103
Push
Pad
LED
Scene Application:
Push Pad (Default settings)
Turn ON from OFF position:
Tap – Scene is activated, Scene LED turns ON.
Turn OFF from ON position:
Tap – Scene is no longer activated, Scene LED
turns OFF.
Virtual Matching Remote Application:
Push Pad (Default settings)
Turn ON from OFF position:
Tap – Lights turn ON, LED turns OFF.
Turn OFF from ON position:
Tap – Lights turn OFF, LED turns ON.
OPERATION
TROUBLESHOOTING
•	 Locator LED on controller does not turn ON
	 -	 Circuit breaker or fuse has tripped.
	 -	 If 1-scene controller is powered up and LED does not turn ON,	
	 check wiring.
•	 Scene controller does not operate lights
	 -	 Check association.
	 -	 Ensure that controller was properly updated.
	 -	 Re-configure the controller button to operate using the AREA ON/OFF
action (refer to VRCPG documentation).
Step 10
NOTE: This step requires a controller that can create association lists to
group 1.
NOTE: One (1) Z-Wave®
device can be associated to multiple programmer/
remotes (up to five (5) programmer/remotes maximum).
NOTE: If using a non-Leviton Programmer/Remote, refer to the
Programmer/Remote instruction sheet for Associating a device.
Once association is complete, you can set a scene as
follows:
•	 Press and hold button on 1-Scene Controller until LED blinks Green.
•	 Adjust devices in area.
•	 Press button again on 1-Scene Controller and the LED will stop blinking.
•	 The scene has now been set.
Definition of Mode
LED Option: Sets the Locator LED timeout to 5 seconds after use.
NOTE: The switch will exit program mode after 3 minutes of inactivity.
To enter programming mode press and hold the push pad for 10 seconds
until the locator LED begins to blink. Upon releasing the push pad the LED
Option will automatically be changed.
ADVANCED PROGRAMMING FEATURES
LOCATOR LED
Default
First toggle
Active
Turns off 5 seconds after use
LOCATOR LED OPTION SETTING
Gently press top
of push pad
G)	 After all devices are included into the network, the controller must
be updated to allow proper network function. To update controller
proceed as follows:
	 •	 If using a non-Leviton Programmer/Remote, refer to the
Programmer/Remote instruction sheet for updating controller.
	 •	 If using Leviton Z-Wave®
Programmer/Remote, Cat. No. VRCPG,
press the Menu button and scroll down to System Setup. Press
the center button to select System
Setup Menu. Press the center
button to select Network. Press
the center button to select Update
cntrl. When prompted, press push
pad on the 1-scene controller.
	 •	 Wait until the VRCPG Programmer/
Remote confirms completion.	
Update is done.
Note: If using the VRCPG's Install
Checklist feature, after all devices are
included, go to Update Controllers step.
Note: If the 1-scene controller has	
been successfully Included in the	
network and the user tries to Include	
it again without first excluding it from the
network, the controller will retain
the first node ID it had received and
ignore the second.
Cat. No. VRCPG
1 ON
2 ON
3 ON
4 ON
OFF
OFF
OFF
OFF
Menu
Button
Center
Button
Including 1-Scene Controller into Z-Wave®
Network:
Step 8 cont'd
This device complies with Part 15 of the FCC Rules. Operation is subject
to following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for
a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment OFF and ON, the user is encouraged to try to
correct the interference by one or more of the following measures:
•	 Reorient or relocate the receiving Antenna.
•	 Increase the separation between the equipment and the receiver.
•	 Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•	 Consult the dealer or an experienced radio/tv technician for help.
FCC COMPLIANCE STATEMENT
Any changes or modifications not expressly approved by Leviton
Manufacturing Co., Inc., could void the user's authority to operate the
equipment.
FCC CAUTION
Step 11b Mixed group or device that does not support
scene:
NOTE: This step requires a 1-Zone Controller or Z-Wave®
Controller that supports Z-Wave®
scene controller configuration
commands.
AREA ON/OFF Application:
Push Button
Turn ON from OFF position:
Press button – Turns all lights in Zone/Area ON, LED turns ON.
LED will blink until Zone/Area is ON.
Turn OFF from ON position:
Press button – Turns all lights in Zone/Area OFF, LED turns OFF.
Dim/Bright:
Press left side of Dim/Bright button - Lights in last activated Zone/Area will
dim.
Press right side of Dim/Bright button - Lights in last activated Zone/Area will
brighten.
NOTE: Controller will only Dim/Bright devices located within direct Radio
Frequency range.
NOTE: LED will be lit Green if any one load in the associated Area is ON.
LED will be OFF when all loads are turned OFF.
If there is a power outage, when the power is restored, the lights will return
to the last setting before the power interruption.
Cleaning: Clean with a damp cloth. DO NOT use chemical cleaners.
Scene Programming:
NOTE: All devices associated to the buttons must support
Z-Wave®
scene command. If a device in the group does not
support the scene command it will not be controlled.
•	 Press and hold button on 1-Scene Controller until LED
blinks Green.
•	 Adjust devices associated to the button.
•	 Press button again on 1-Scene Controller and the LED will
stop blinking.
•	 The scene has now been set.
Step 11a

Más contenido relacionado

La actualidad más candente

Digital Watchdog DW-V960H1612T User Manual
Digital Watchdog DW-V960H1612T User ManualDigital Watchdog DW-V960H1612T User Manual
Digital Watchdog DW-V960H1612T User ManualJMAC Supply
 
LM26484 Power Management Unit
LM26484 Power Management Unit LM26484 Power Management Unit
LM26484 Power Management Unit Premier Farnell
 
land rover robot control using GSM technology
land rover robot control using GSM technologyland rover robot control using GSM technology
land rover robot control using GSM technologyJOLLUSUDARSHANREDDY
 
Pentax GNSS
Pentax GNSSPentax GNSS
Pentax GNSSOpenmaps
 
Wireless speed Control or Wireless Regulator
Wireless speed Control or Wireless RegulatorWireless speed Control or Wireless Regulator
Wireless speed Control or Wireless RegulatorHîmãńshu Mêęńä
 
Cad100200 2007 05-18-pc_2003-06-20
Cad100200 2007 05-18-pc_2003-06-20Cad100200 2007 05-18-pc_2003-06-20
Cad100200 2007 05-18-pc_2003-06-20Mick Carrasco
 
project presentation on cell phone operated land rover
project presentation on cell phone operated land roverproject presentation on cell phone operated land rover
project presentation on cell phone operated land roversunanda kothari
 
Ppt land rover
Ppt land roverPpt land rover
Ppt land roverAshu0711
 
Cellphone land rover using micro controller
Cellphone land rover using micro controllerCellphone land rover using micro controller
Cellphone land rover using micro controllerharideepu
 
cell phone based device control
cell phone based device controlcell phone based device control
cell phone based device controlstudent
 
Programmable Home Security Alarm System
Programmable Home Security Alarm SystemProgrammable Home Security Alarm System
Programmable Home Security Alarm SystemDilshan Jayakody
 
Beachtek DXA-SLR
Beachtek DXA-SLRBeachtek DXA-SLR
Beachtek DXA-SLRAV ProfShop
 
Rci2950 dx70 150-owners
Rci2950 dx70 150-ownersRci2950 dx70 150-owners
Rci2950 dx70 150-ownersnobster123
 
Cell Phone Operated Land Rover
Cell Phone Operated Land RoverCell Phone Operated Land Rover
Cell Phone Operated Land RoverSayanton Vhaduri
 
Beachtek DXA-5DA
Beachtek DXA-5DABeachtek DXA-5DA
Beachtek DXA-5DAAV ProfShop
 
Cell operated land rover robot
Cell operated land rover robotCell operated land rover robot
Cell operated land rover robotChetan Kataria
 
Data sheet en_us_1860652043
Data sheet en_us_1860652043Data sheet en_us_1860652043
Data sheet en_us_1860652043amthanhbosch
 
Ls catalog thiet bi tu dong i e5_e_1105_dienhathe.vn
Ls catalog thiet bi tu dong i e5_e_1105_dienhathe.vnLs catalog thiet bi tu dong i e5_e_1105_dienhathe.vn
Ls catalog thiet bi tu dong i e5_e_1105_dienhathe.vnDien Ha The
 

La actualidad más candente (18)

Digital Watchdog DW-V960H1612T User Manual
Digital Watchdog DW-V960H1612T User ManualDigital Watchdog DW-V960H1612T User Manual
Digital Watchdog DW-V960H1612T User Manual
 
LM26484 Power Management Unit
LM26484 Power Management Unit LM26484 Power Management Unit
LM26484 Power Management Unit
 
land rover robot control using GSM technology
land rover robot control using GSM technologyland rover robot control using GSM technology
land rover robot control using GSM technology
 
Pentax GNSS
Pentax GNSSPentax GNSS
Pentax GNSS
 
Wireless speed Control or Wireless Regulator
Wireless speed Control or Wireless RegulatorWireless speed Control or Wireless Regulator
Wireless speed Control or Wireless Regulator
 
Cad100200 2007 05-18-pc_2003-06-20
Cad100200 2007 05-18-pc_2003-06-20Cad100200 2007 05-18-pc_2003-06-20
Cad100200 2007 05-18-pc_2003-06-20
 
project presentation on cell phone operated land rover
project presentation on cell phone operated land roverproject presentation on cell phone operated land rover
project presentation on cell phone operated land rover
 
Ppt land rover
Ppt land roverPpt land rover
Ppt land rover
 
Cellphone land rover using micro controller
Cellphone land rover using micro controllerCellphone land rover using micro controller
Cellphone land rover using micro controller
 
cell phone based device control
cell phone based device controlcell phone based device control
cell phone based device control
 
Programmable Home Security Alarm System
Programmable Home Security Alarm SystemProgrammable Home Security Alarm System
Programmable Home Security Alarm System
 
Beachtek DXA-SLR
Beachtek DXA-SLRBeachtek DXA-SLR
Beachtek DXA-SLR
 
Rci2950 dx70 150-owners
Rci2950 dx70 150-ownersRci2950 dx70 150-owners
Rci2950 dx70 150-owners
 
Cell Phone Operated Land Rover
Cell Phone Operated Land RoverCell Phone Operated Land Rover
Cell Phone Operated Land Rover
 
Beachtek DXA-5DA
Beachtek DXA-5DABeachtek DXA-5DA
Beachtek DXA-5DA
 
Cell operated land rover robot
Cell operated land rover robotCell operated land rover robot
Cell operated land rover robot
 
Data sheet en_us_1860652043
Data sheet en_us_1860652043Data sheet en_us_1860652043
Data sheet en_us_1860652043
 
Ls catalog thiet bi tu dong i e5_e_1105_dienhathe.vn
Ls catalog thiet bi tu dong i e5_e_1105_dienhathe.vnLs catalog thiet bi tu dong i e5_e_1105_dienhathe.vn
Ls catalog thiet bi tu dong i e5_e_1105_dienhathe.vn
 

Similar a Leviton vrcs1 1 l

Leviton vrp15 z Installation Instructions and Setup Guide
Leviton vrp15 z Installation Instructions and Setup GuideLeviton vrp15 z Installation Instructions and Setup Guide
Leviton vrp15 z Installation Instructions and Setup GuideAlarm Grid
 
Vision ZG8101 Wireless Garage Door Detector - Installation Manual
Vision ZG8101 Wireless Garage Door Detector - Installation ManualVision ZG8101 Wireless Garage Door Detector - Installation Manual
Vision ZG8101 Wireless Garage Door Detector - Installation ManualDomotica daVinci
 
Aeon labs zw130 wall mote quad instructions
Aeon labs zw130 wall mote quad instructionsAeon labs zw130 wall mote quad instructions
Aeon labs zw130 wall mote quad instructionsDomotica daVinci
 
Datavideo TLM-702
Datavideo TLM-702Datavideo TLM-702
Datavideo TLM-702AV ProfShop
 
Datavideo TLM-702
Datavideo TLM-702Datavideo TLM-702
Datavideo TLM-702AV ProfShop
 
Aeon labs wall mote manual
Aeon labs wall mote manualAeon labs wall mote manual
Aeon labs wall mote manualDomotica daVinci
 
Manual widom universal roller shutter en
Manual widom universal roller shutter enManual widom universal roller shutter en
Manual widom universal roller shutter enDomotica daVinci
 
Manual Smart Switch Walli Fibaro
Manual Smart Switch Walli FibaroManual Smart Switch Walli Fibaro
Manual Smart Switch Walli FibaroDomotica daVinci
 
Manual aeon labs heavy duty smart switch gen5
Manual   aeon labs heavy duty smart switch gen5Manual   aeon labs heavy duty smart switch gen5
Manual aeon labs heavy duty smart switch gen5Domotica daVinci
 
Door sensor multisensor 4_ in_1 Zipato Z-Wave Plus
Door sensor  multisensor 4_ in_1 Zipato Z-Wave PlusDoor sensor  multisensor 4_ in_1 Zipato Z-Wave Plus
Door sensor multisensor 4_ in_1 Zipato Z-Wave PlusDomotica daVinci
 
Scenes controller z wave plus remotec
Scenes controller z wave plus remotecScenes controller z wave plus remotec
Scenes controller z wave plus remotecDomotica daVinci
 
Datavideo TLM-433
Datavideo TLM-433Datavideo TLM-433
Datavideo TLM-433AV ProfShop
 
Datavideo TLM-433
Datavideo TLM-433Datavideo TLM-433
Datavideo TLM-433AV ProfShop
 
Range extender 7 - Aeotec - Manual
Range extender 7 - Aeotec - Manual   Range extender 7 - Aeotec - Manual
Range extender 7 - Aeotec - Manual Domotica daVinci
 
Manual neocoolcam door sensor
Manual neocoolcam door sensorManual neocoolcam door sensor
Manual neocoolcam door sensorDomotica daVinci
 
wiDom Energy Driven Switch C version and L version manual
wiDom Energy Driven Switch C version and L version manualwiDom Energy Driven Switch C version and L version manual
wiDom Energy Driven Switch C version and L version manualDomotica daVinci
 
Manual steinel rs led d2 (indoor light with led)
Manual steinel rs led d2 (indoor light with led)Manual steinel rs led d2 (indoor light with led)
Manual steinel rs led d2 (indoor light with led)Domotica daVinci
 

Similar a Leviton vrcs1 1 l (20)

Leviton vrp15 z Installation Instructions and Setup Guide
Leviton vrp15 z Installation Instructions and Setup GuideLeviton vrp15 z Installation Instructions and Setup Guide
Leviton vrp15 z Installation Instructions and Setup Guide
 
Vision ZG8101 Wireless Garage Door Detector - Installation Manual
Vision ZG8101 Wireless Garage Door Detector - Installation ManualVision ZG8101 Wireless Garage Door Detector - Installation Manual
Vision ZG8101 Wireless Garage Door Detector - Installation Manual
 
Aeon labs zw130 wall mote quad instructions
Aeon labs zw130 wall mote quad instructionsAeon labs zw130 wall mote quad instructions
Aeon labs zw130 wall mote quad instructions
 
Datavideo TLM-702
Datavideo TLM-702Datavideo TLM-702
Datavideo TLM-702
 
Datavideo TLM-702
Datavideo TLM-702Datavideo TLM-702
Datavideo TLM-702
 
Aeon labs wall mote manual
Aeon labs wall mote manualAeon labs wall mote manual
Aeon labs wall mote manual
 
Manual widom universal roller shutter en
Manual widom universal roller shutter enManual widom universal roller shutter en
Manual widom universal roller shutter en
 
Manual Smart Switch Walli Fibaro
Manual Smart Switch Walli FibaroManual Smart Switch Walli Fibaro
Manual Smart Switch Walli Fibaro
 
Manual aeon labs heavy duty smart switch gen5
Manual   aeon labs heavy duty smart switch gen5Manual   aeon labs heavy duty smart switch gen5
Manual aeon labs heavy duty smart switch gen5
 
manual dimmer - Zipato
manual dimmer - Zipatomanual dimmer - Zipato
manual dimmer - Zipato
 
Door sensor multisensor 4_ in_1 Zipato Z-Wave Plus
Door sensor  multisensor 4_ in_1 Zipato Z-Wave PlusDoor sensor  multisensor 4_ in_1 Zipato Z-Wave Plus
Door sensor multisensor 4_ in_1 Zipato Z-Wave Plus
 
Scenes controller z wave plus remotec
Scenes controller z wave plus remotecScenes controller z wave plus remotec
Scenes controller z wave plus remotec
 
Manual danfos danehc10
Manual danfos danehc10Manual danfos danehc10
Manual danfos danehc10
 
Datavideo TLM-433
Datavideo TLM-433Datavideo TLM-433
Datavideo TLM-433
 
Datavideo TLM-433
Datavideo TLM-433Datavideo TLM-433
Datavideo TLM-433
 
Range extender 7 - Aeotec - Manual
Range extender 7 - Aeotec - Manual   Range extender 7 - Aeotec - Manual
Range extender 7 - Aeotec - Manual
 
Manual neocoolcam door sensor
Manual neocoolcam door sensorManual neocoolcam door sensor
Manual neocoolcam door sensor
 
wiDom Energy Driven Switch C version and L version manual
wiDom Energy Driven Switch C version and L version manualwiDom Energy Driven Switch C version and L version manual
wiDom Energy Driven Switch C version and L version manual
 
Manual steinel rs led d2 (indoor light with led)
Manual steinel rs led d2 (indoor light with led)Manual steinel rs led d2 (indoor light with led)
Manual steinel rs led d2 (indoor light with led)
 
User manual-475876
User manual-475876User manual-475876
User manual-475876
 

Más de Alarm Grid

Vizia rf + system programming and control
Vizia rf + system programming and controlVizia rf + system programming and control
Vizia rf + system programming and controlAlarm Grid
 
Vizia rf + plug in spec sheet
Vizia rf + plug in spec sheetVizia rf + plug in spec sheet
Vizia rf + plug in spec sheetAlarm Grid
 
Leviton vrs15 1 lz installation manual and setup guide
Leviton vrs15 1 lz installation manual and setup guideLeviton vrs15 1 lz installation manual and setup guide
Leviton vrs15 1 lz installation manual and setup guideAlarm Grid
 
Leviton vrs05 1 lz installation manual and setup guide
Leviton vrs05 1 lz installation manual and setup guideLeviton vrs05 1 lz installation manual and setup guide
Leviton vrs05 1 lz installation manual and setup guideAlarm Grid
 
Leviton vrr15 1 lz product specification bulletin
Leviton vrr15 1 lz product specification bulletinLeviton vrr15 1 lz product specification bulletin
Leviton vrr15 1 lz product specification bulletinAlarm Grid
 
Leviton vrp03 z product manual and setup guide
Leviton vrp03 z product manual and setup guideLeviton vrp03 z product manual and setup guide
Leviton vrp03 z product manual and setup guideAlarm Grid
 
Leviton vri10 1 lz product manual and setup guide
Leviton vri10 1 lz product manual and setup guideLeviton vri10 1 lz product manual and setup guide
Leviton vri10 1 lz product manual and setup guideAlarm Grid
 
Leviton vri06 1 lz product manual and setup guide
Leviton vri06 1 lz product manual and setup guideLeviton vri06 1 lz product manual and setup guide
Leviton vri06 1 lz product manual and setup guideAlarm Grid
 
Leviton vre06 1 lz
Leviton vre06 1 lzLeviton vre06 1 lz
Leviton vre06 1 lzAlarm Grid
 
Leviton vrcz4 mr, vrcs4-mr, and vrc52-mr product specifications
Leviton vrcz4 mr, vrcs4-mr, and vrc52-mr product specificationsLeviton vrcz4 mr, vrcs4-mr, and vrc52-mr product specifications
Leviton vrcz4 mr, vrcs4-mr, and vrc52-mr product specificationsAlarm Grid
 
Leviton vrcz4 1 l, vrcs4-1l, vrcz1-1l, vrcs1-1l and vrmr1-osg product specifi...
Leviton vrcz4 1 l, vrcs4-1l, vrcz1-1l, vrcs1-1l and vrmr1-osg product specifi...Leviton vrcz4 1 l, vrcs4-1l, vrcz1-1l, vrcs1-1l and vrmr1-osg product specifi...
Leviton vrcz4 1 l, vrcs4-1l, vrcz1-1l, vrcs1-1l and vrmr1-osg product specifi...Alarm Grid
 
Leviton vp00 r 10z, vp00r-1lz, vp0sr-10z, vp0sr-1lz installation manual and s...
Leviton vp00 r 10z, vp00r-1lz, vp0sr-10z, vp0sr-1lz installation manual and s...Leviton vp00 r 10z, vp00r-1lz, vp0sr-10z, vp0sr-1lz installation manual and s...
Leviton vp00 r 10z, vp00r-1lz, vp0sr-10z, vp0sr-1lz installation manual and s...Alarm Grid
 
Leviton dimmers, switches and fan speed controllers
Leviton dimmers, switches and fan speed controllersLeviton dimmers, switches and fan speed controllers
Leviton dimmers, switches and fan speed controllersAlarm Grid
 
Fluorescent dimmer for hi lume or eco-10 ballasts
Fluorescent dimmer for hi lume or eco-10 ballastsFluorescent dimmer for hi lume or eco-10 ballasts
Fluorescent dimmer for hi lume or eco-10 ballastsAlarm Grid
 
Controlling z wave door locks with the vrc0 p
Controlling z wave door locks with the vrc0 pControlling z wave door locks with the vrc0 p
Controlling z wave door locks with the vrc0 pAlarm Grid
 
Vizia rf+ collection
Vizia rf+ collectionVizia rf+ collection
Vizia rf+ collectionAlarm Grid
 
Honeywell vista-50p-user-guide
Honeywell vista-50p-user-guideHoneywell vista-50p-user-guide
Honeywell vista-50p-user-guideAlarm Grid
 
Honeywell vista-50p-install-guide
Honeywell vista-50p-install-guideHoneywell vista-50p-install-guide
Honeywell vista-50p-install-guideAlarm Grid
 
Honeywell vista-50p-connections-summary
Honeywell vista-50p-connections-summaryHoneywell vista-50p-connections-summary
Honeywell vista-50p-connections-summaryAlarm Grid
 
Honeywell vista-10p-programming-guide
Honeywell vista-10p-programming-guideHoneywell vista-10p-programming-guide
Honeywell vista-10p-programming-guideAlarm Grid
 

Más de Alarm Grid (20)

Vizia rf + system programming and control
Vizia rf + system programming and controlVizia rf + system programming and control
Vizia rf + system programming and control
 
Vizia rf + plug in spec sheet
Vizia rf + plug in spec sheetVizia rf + plug in spec sheet
Vizia rf + plug in spec sheet
 
Leviton vrs15 1 lz installation manual and setup guide
Leviton vrs15 1 lz installation manual and setup guideLeviton vrs15 1 lz installation manual and setup guide
Leviton vrs15 1 lz installation manual and setup guide
 
Leviton vrs05 1 lz installation manual and setup guide
Leviton vrs05 1 lz installation manual and setup guideLeviton vrs05 1 lz installation manual and setup guide
Leviton vrs05 1 lz installation manual and setup guide
 
Leviton vrr15 1 lz product specification bulletin
Leviton vrr15 1 lz product specification bulletinLeviton vrr15 1 lz product specification bulletin
Leviton vrr15 1 lz product specification bulletin
 
Leviton vrp03 z product manual and setup guide
Leviton vrp03 z product manual and setup guideLeviton vrp03 z product manual and setup guide
Leviton vrp03 z product manual and setup guide
 
Leviton vri10 1 lz product manual and setup guide
Leviton vri10 1 lz product manual and setup guideLeviton vri10 1 lz product manual and setup guide
Leviton vri10 1 lz product manual and setup guide
 
Leviton vri06 1 lz product manual and setup guide
Leviton vri06 1 lz product manual and setup guideLeviton vri06 1 lz product manual and setup guide
Leviton vri06 1 lz product manual and setup guide
 
Leviton vre06 1 lz
Leviton vre06 1 lzLeviton vre06 1 lz
Leviton vre06 1 lz
 
Leviton vrcz4 mr, vrcs4-mr, and vrc52-mr product specifications
Leviton vrcz4 mr, vrcs4-mr, and vrc52-mr product specificationsLeviton vrcz4 mr, vrcs4-mr, and vrc52-mr product specifications
Leviton vrcz4 mr, vrcs4-mr, and vrc52-mr product specifications
 
Leviton vrcz4 1 l, vrcs4-1l, vrcz1-1l, vrcs1-1l and vrmr1-osg product specifi...
Leviton vrcz4 1 l, vrcs4-1l, vrcz1-1l, vrcs1-1l and vrmr1-osg product specifi...Leviton vrcz4 1 l, vrcs4-1l, vrcz1-1l, vrcs1-1l and vrmr1-osg product specifi...
Leviton vrcz4 1 l, vrcs4-1l, vrcz1-1l, vrcs1-1l and vrmr1-osg product specifi...
 
Leviton vp00 r 10z, vp00r-1lz, vp0sr-10z, vp0sr-1lz installation manual and s...
Leviton vp00 r 10z, vp00r-1lz, vp0sr-10z, vp0sr-1lz installation manual and s...Leviton vp00 r 10z, vp00r-1lz, vp0sr-10z, vp0sr-1lz installation manual and s...
Leviton vp00 r 10z, vp00r-1lz, vp0sr-10z, vp0sr-1lz installation manual and s...
 
Leviton dimmers, switches and fan speed controllers
Leviton dimmers, switches and fan speed controllersLeviton dimmers, switches and fan speed controllers
Leviton dimmers, switches and fan speed controllers
 
Fluorescent dimmer for hi lume or eco-10 ballasts
Fluorescent dimmer for hi lume or eco-10 ballastsFluorescent dimmer for hi lume or eco-10 ballasts
Fluorescent dimmer for hi lume or eco-10 ballasts
 
Controlling z wave door locks with the vrc0 p
Controlling z wave door locks with the vrc0 pControlling z wave door locks with the vrc0 p
Controlling z wave door locks with the vrc0 p
 
Vizia rf+ collection
Vizia rf+ collectionVizia rf+ collection
Vizia rf+ collection
 
Honeywell vista-50p-user-guide
Honeywell vista-50p-user-guideHoneywell vista-50p-user-guide
Honeywell vista-50p-user-guide
 
Honeywell vista-50p-install-guide
Honeywell vista-50p-install-guideHoneywell vista-50p-install-guide
Honeywell vista-50p-install-guide
 
Honeywell vista-50p-connections-summary
Honeywell vista-50p-connections-summaryHoneywell vista-50p-connections-summary
Honeywell vista-50p-connections-summary
 
Honeywell vista-10p-programming-guide
Honeywell vista-10p-programming-guideHoneywell vista-10p-programming-guide
Honeywell vista-10p-programming-guide
 

Leviton vrcs1 1 l

  • 1. NOTES: • If using a non-Leviton Programmer/Remote, refer to the Programmer/Remote instruction sheet. • 1-scene controllers included into a Z-Wave® network must be updated after you have included all other devices. • If using the VRCPG's Install Checklist feature, go directly to Step C. A) If using a Leviton Z-Wave® Programmer/Remote, Cat. No. VRCPG, press the Menu button and scroll down to System Setup. Press the center button to select System Setup Menu. Choose Advanced Settings. Press the center button to select Network. Press the center button to <Include Node>. B) If using VRCPG Programmer/Remote, you will be prompted to place 1-scene controller into programming mode. C) To access Program mode, engage the air-gap switch by gently pressing the top of the push pad until the bottom lifts completely out of the frame and a click is heard (refer to figure). Wait 5 seconds and then press the push pad back into the frame and hold push pad until the LED turns Amber. Release the push pad and the LED should blink Amber. You are now in Programming mode. NOTE: If the LED on the 1-scene controller turns solid Red while including, there has been a communication error. D) While standing close to the 1-scene controller (approximately 2-5 ft.), press the center button on the Programmer/Remote to <Include> device in the network. NOTE: Only one device may be included at any time. E) The VRCPG Programmer/Remote will assign a Home ID, Node ID, and Name for this device. NOTE: This information will be stored in the Programmer/Remote to be used for future reference. NOTE: You may edit the name of this device at this time. F) The 1-scene controller is now installed in the network. WARNINGS AND CAUTIONS: • ON/OFF LED for 2-way status reporting. • To be installed and/or used in accordance with appropriate electrical codes and regulations. • If you are unsure about any part of these instructions, consult a qualified electrician. • Vizia RF +TM VRCS1 1-Scene Controller does not control the load, but provides remote operation with Vizia RF +TM switches. • Recommended minimum wall box depth is 2-1/2". WARNINGS AND CAUTIONS: • No traveler wires are needed. Remote controls via radio frequency (RF) technology. • Can call one (1) scene ON/OFF or area ON/OFF with advanced Programmer/Remote (see VRCPG). • For a complete set-up, a controller supporting the advanced Z-Wave® scene features is needed, such as the advanced Programming Remote (VRCPG). • Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture. • Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL. 1-Scene Controller/ Virtual Matching Switch Remote Cat. No. VRCS1 120VAC, 60Hz Installation Instructions DI-000-VRCS1-02B Tools needed to install your 1-Scene Controller Slotted/Phillips Screwdriver Electrical Tape Pliers Pencil Cutters Ruler Changing the color of your 1-Scene Controller: Your device may include color options. To change color of the face, proceed as follows: Line up tabs and press in sides one at a time to attach Push in side at tab to release INSTALLING YOUR 1-SCENE CONTROLLER NOTE: Use check boxes when Steps are completed. WARNING: TO AVOID FIRE, SHOCK OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring! Step 1 Step 3 Preparing and connecting wires: This 1-scene controller can be wired using side wire terminal screws or through backwire openings. Choose appropriate wire stripping specifications accordingly. • Make sure that the ends of the wires from the wall box are straight (cut if necessary). 5/8" (1.6 cm) Strip Gage (measure bare wire here)Cut (if necessary) Side Wire Connection Side wire terminals accept #14 AWG solid wire copper only. Back Wire (either hole may be used) Back wire openings use #14-12 AWG solid wire copper only. WIRING 1-SCENE CONTROLLER: Connect wires per WIRING DIAGRAM as follows: • Green or bare copper wire in wall box to Green terminal screw. • Line Hot wall box wire to terminal screw marked "BK". • Line Neutral wall box wire to terminal screw marked "WH". • Proceed to Step 5. • Position all wires to provide room in outlet wall box for device. • Ensure that the word “TOP” is facing up on device strap. • Partially screw in mounting screws in wall box mounting holes. NOTE: Dress wires with a bend as shown in diagram in order to relieve stress when mounting device. • Restore power at circuit breaker or fuse. • LED should turn ON. If LED does not turn ON, refer to the TROUBLESHOOTING section. Testing your 1-Scene Controller prior to mounting in wall box: Step 5 Gently press top of push pad Wiring Application: Hot (Black) Neutral (White) Line 120VAC, 60Hz BKWH Green Ground 1-Scene Controller Step 4 2 3 1 2 1. Line (Hot) 2. Neutral 3. Ground Identifying your wiring application (most common): NOTE: If the wiring in your wall box does not resemble this configuration, consult a qualified electrician. Step 2 INTRODUCTION Leviton’s Vizia RF +TM components are designed to communicate with each other via Radio Frequency (RF) to provide remote control of your lighting. Using RF technology allows Leviton to provide the greatest signal integrity possible. Each module in Leviton’s Vizia RF +TM component line is a Z-Wave® enabled device. In a Z-Wave® network, each device is designed to act as a router. These routers will re-transmit the RF signal from one device to another until the intended device is reached. This ensures that the signal is received by its intended device by routing the signal around obstacles and radio dead spots. This 1-Scene controller is meant to control special scene enabled Z-Wave® products. To control groups of devices that are mixed or do not support scene command class use the Leviton 1-Zone Controller (VRCZ1). Setting up this device requires specific advanced controller functionalities, your controller must be able to associate device to groups and must be able to control the scene controller configuration commands such as the advanced Programming Remote (VRCPG). • This is a Z-Wave® Controller • 3-way or 4-way control without traveler wires • Can call 1 scene • ON/OFF LED • Two way communication • RF reliability • Ease of installation – No new wiring • Compatible with other Z-Wave® enabled devices FEATURES Including 1-Scene Controller into Z-Wave® Network: Step 8 Restore Power: Restore power at circuit breaker or fuse. Installation is complete. 1-Scene Controller Mounting: TURN OFF POWER AT CIRCUIT BREAKER OR FUSE. Step 6 Installation may now be completed by tightening mounting screws into wall box. Attach wallplate. Step 7
  • 2. Device Association: After inclusion process, you must associate the devices to the controllers. Refer to the Primary Programmer/ Remote instruction sheet for complete details. A) If using a Leviton Z-Wave® Programmer/Remote, Cat. No. VRCPG, press the Menu button and scroll down to System Setup. Press the center button to select System Setup Menu. Choose Advanced Settings. Press the center button to select Network. Scroll down to <Exclude Node> and press the center button. B) If using VRCPG Programmer/Remote, you will be prompted to place 1-scene controller into programming mode. C) To access Program mode, engage the air-gap switch by gently pressing the top of the push pad until the bottom lifts completely out of the frame and a click is heard (refer to figure). Wait 5 seconds and then press the push pad back into the frame and hold push pad until the LED turns Amber. Release the push pad and the LED should blink Amber. You are now in Programming mode. NOTE: If the LED on the 1-scene controller turns solid Red while excluding, there has been a communication error. D) While standing close to the 1-scene controller (approximately 2-5 ft.), press the center button to <Exclude> device from the network. Factory Default: If your 1-scene controller is not responding, or you are unable to control it after you have tried to Include/Exclude it multiple times, it may be necessary to reset the 1-scene controller to its original factory settings. To accomplish this, proceed as follows: • On the 1-scene controller, engage the air-gap switch by gently pressing the top of the push pad until the bottom lifts completely out of the frame and a click is heard (refer to figure). Wait 5 seconds and then press the push pad back into the frame and hold push pad until the locator LED turns Amber and then flashes Red. Release the push pad. The 1-scene controller is now reset. Once the controller is reset, it will be necessary to Re-Include it to a network before it can be used. CAUTION: SETTING A DEVICE TO A FACTORY DEFAULT DOES NOT EXCLUDE THAT DEVICE FROM A NETWORK. THE EXCLUSION PROCEDURE MUST STILL BE FOLLOWED TO REMOVE THE DEVICE FROM THE PRIMARY PROGRAMMER/REMOTE'S INFORMATION TABLE. FAILURE TO DO SO MAY RESULT IN SYSTEM THAT IS SLOW TO RESPOND, OR MAY FAIL TO RESPOND TO SOME DEVICES. DI-000-VRCS1-02B© 2009 Leviton Mfg. Co., Inc. LIMITED 5 YEAR WARRANTY AND EXCLUSIONS Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, New York 11747. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise. Programmer/Remote Cat. No. VRCPG NOTE: Programmer/Remote must be in close proximity to 1-scene controller when including in the network. Step 9 Excluding 1-Scene Controller from Z-Wave® Network: For additional information, contact Leviton’s Techline at 1-800-824-3005 or visit Leviton’s website at www.ViziaRFplus.com Protected under U.S. Patent Number 6,388,399 and patents pending and licensed under U.S. Patents Numbers 5,905,442, and 5,982,103 Push Pad LED Scene Application: Push Pad (Default settings) Turn ON from OFF position: Tap – Scene is activated, Scene LED turns ON. Turn OFF from ON position: Tap – Scene is no longer activated, Scene LED turns OFF. Virtual Matching Remote Application: Push Pad (Default settings) Turn ON from OFF position: Tap – Lights turn ON, LED turns OFF. Turn OFF from ON position: Tap – Lights turn OFF, LED turns ON. OPERATION TROUBLESHOOTING • Locator LED on controller does not turn ON - Circuit breaker or fuse has tripped. - If 1-scene controller is powered up and LED does not turn ON, check wiring. • Scene controller does not operate lights - Check association. - Ensure that controller was properly updated. - Re-configure the controller button to operate using the AREA ON/OFF action (refer to VRCPG documentation). Step 10 NOTE: This step requires a controller that can create association lists to group 1. NOTE: One (1) Z-Wave® device can be associated to multiple programmer/ remotes (up to five (5) programmer/remotes maximum). NOTE: If using a non-Leviton Programmer/Remote, refer to the Programmer/Remote instruction sheet for Associating a device. Once association is complete, you can set a scene as follows: • Press and hold button on 1-Scene Controller until LED blinks Green. • Adjust devices in area. • Press button again on 1-Scene Controller and the LED will stop blinking. • The scene has now been set. Definition of Mode LED Option: Sets the Locator LED timeout to 5 seconds after use. NOTE: The switch will exit program mode after 3 minutes of inactivity. To enter programming mode press and hold the push pad for 10 seconds until the locator LED begins to blink. Upon releasing the push pad the LED Option will automatically be changed. ADVANCED PROGRAMMING FEATURES LOCATOR LED Default First toggle Active Turns off 5 seconds after use LOCATOR LED OPTION SETTING Gently press top of push pad G) After all devices are included into the network, the controller must be updated to allow proper network function. To update controller proceed as follows: • If using a non-Leviton Programmer/Remote, refer to the Programmer/Remote instruction sheet for updating controller. • If using Leviton Z-Wave® Programmer/Remote, Cat. No. VRCPG, press the Menu button and scroll down to System Setup. Press the center button to select System Setup Menu. Press the center button to select Network. Press the center button to select Update cntrl. When prompted, press push pad on the 1-scene controller. • Wait until the VRCPG Programmer/ Remote confirms completion. Update is done. Note: If using the VRCPG's Install Checklist feature, after all devices are included, go to Update Controllers step. Note: If the 1-scene controller has been successfully Included in the network and the user tries to Include it again without first excluding it from the network, the controller will retain the first node ID it had received and ignore the second. Cat. No. VRCPG 1 ON 2 ON 3 ON 4 ON OFF OFF OFF OFF Menu Button Center Button Including 1-Scene Controller into Z-Wave® Network: Step 8 cont'd This device complies with Part 15 of the FCC Rules. Operation is subject to following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving Antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/tv technician for help. FCC COMPLIANCE STATEMENT Any changes or modifications not expressly approved by Leviton Manufacturing Co., Inc., could void the user's authority to operate the equipment. FCC CAUTION Step 11b Mixed group or device that does not support scene: NOTE: This step requires a 1-Zone Controller or Z-Wave® Controller that supports Z-Wave® scene controller configuration commands. AREA ON/OFF Application: Push Button Turn ON from OFF position: Press button – Turns all lights in Zone/Area ON, LED turns ON. LED will blink until Zone/Area is ON. Turn OFF from ON position: Press button – Turns all lights in Zone/Area OFF, LED turns OFF. Dim/Bright: Press left side of Dim/Bright button - Lights in last activated Zone/Area will dim. Press right side of Dim/Bright button - Lights in last activated Zone/Area will brighten. NOTE: Controller will only Dim/Bright devices located within direct Radio Frequency range. NOTE: LED will be lit Green if any one load in the associated Area is ON. LED will be OFF when all loads are turned OFF. If there is a power outage, when the power is restored, the lights will return to the last setting before the power interruption. Cleaning: Clean with a damp cloth. DO NOT use chemical cleaners. Scene Programming: NOTE: All devices associated to the buttons must support Z-Wave® scene command. If a device in the group does not support the scene command it will not be controlled. • Press and hold button on 1-Scene Controller until LED blinks Green. • Adjust devices associated to the button. • Press button again on 1-Scene Controller and the LED will stop blinking. • The scene has now been set. Step 11a