Buy Autel MaxiDAS DS708 Get MaxiTPMS TS401 As Free Gift
1. One Year Free Update Online!
2. Shipped from our US warehouse directly, NO TAX, with fast delivery
3. Wifi Available, Cover more than 40 brands of Vehicles from US, Asian and European
So einfach geht modernes Roaming fuer Notes und Nomad.pdf
Wobd2-autel maxi das ds708 connection tips
1. Autel MaxiDAS DS708 Connection Tips
How to connect the genuine Autel MaxiDAS DS708 to a vehicle? The method used to connect
Autel DS708 to a vehicle's DLC depends on the vehicle's configuration--- with OBD II vehicle
management system or not. This is about original Autel MaxiDAS DS708 connection. Hope it can
help you out.
Ps. This connection tips are better for DS708 at www.wobd2.com.
OBD II vehicles supply both communication and 12-volt power through a standardized J-1962
data link connection (DLC).
Non-OBD II vehicles supply communication through a DLC connection and sometimes supplies
12-volt power through the cigarette lighter receptacle or a connection to the battery.
2. a. OBD II Vehicle Cable Connection
Requirement:
OBD II adapter;
15-pin main cable;
steps:
1. Locate the required OBD II adapter and connect it into the 15-pin male
connector of the main cable.
3. 2. Connect the cable's 15-pin female adapter to the DB 15-pin port on the top
of the scan tool. Finger tighten the connecting screws.
4. Connect the cable's OBD II adapter into the vehicle's DLC, located under
the vehicle dash
4. NOTE: Extension cable can be used between the scan tool and the 15-pin
main cable.
b. Non-OBD II Vehicle Cable Connection
three possible conditions for Non-OBD II Vehicle Cable Connection:
1) DLC connection supplies both communication and power;
2) DLC connection supplies communication, and power is to be supplied via
cigarette lighter connection;
5. 3) DLC connection supplies communication, and power is to be supplied
through cable connection to vehicle battery.
-Condition 1
Requirements:
the vehicle-specific OBD I adapter;
the 15-pin main cable;
Steps:
1. Locate the required OBD I adapter and connect the adapter's 15-pin
adapter to the cable's 15-pin male adapter.
2. Connect the cable's 15-pin female adapter to the DB15 port on the top of
the scan tool. Finger tighten the connecting screws.
3. Connect the main cable's OBD I adapter into the vehicle's DLC.
6. -Condition 2
If the DLC connection does not supply power to the scan tool, connection to
the cigarette lighter receptacle will be needed.
Requirement:
Clipper cable;
7. Steps:
1. Connect the clipper cable with the scan tool.
2. Connect the cable's power plug into the vehicle's cigarette lighter
receptacle.
8. NOTE: The vehicle's DLC is not always located under the dash as shown
above.
NOTE: Some adapters may have more than one adapter or may have test
leads instead of an adapter. Whatever the case, make the required
connections to the vehicle's DLC.
-Condition 3
If the clipper cable connection does not provide power either, connection to
the vehicle's battery is necessary.
Requirement:
cigarette lighter;
clipper cable;
9. Steps:
1. Connect the cigarette lighter to the clipper cable.
2. Connect the clipper cable to the vehicle's battery.
NOTE: The vehicle's battery is usually located beside the engine.
NOTE: Please connect the red clipper to the anode and the black clipper to
10. the cathode.
WARNING: The clippers might be hot after use. Be careful not to be burnt.
You can conveniently obtain power supply through power adapter connection
to the scan tool if any power socket is within reach.
HKSC39-B Autel MaxiDAS DS708
http://www.wobd2.com/wholesale/autel-maxidas-ds708-1213.html