Improved version

1. 3.3) Transmitting and3.3) Transmitting and
ReceivingReceiving

2. • Different concepts covered include:
• transmission of data
• protocols
• handshaking
• networks and their topologies
• network access methods
• Transmission of data occurs in two ways:
• parallel transmission
• serial transmission

3. • Parallel transmission is the transmission of
data simultaneously using separate
channels.
• Serial transmission transmits the data one
bit after the other along one channel.
• Parallel is faster, but can only be used over
shorter distances.
• The direction of data flow can be:
• simplex
• half-duplex
• full-duplex

4. • Simplex mode allows transmission in one
direction only.
• Half-duplex allows transmission in either
direction, but only in one direction at a
time.
• Full duplex allows transmission in both
directions simultaneously.

5. • Serial transmission can be either
asynchronous or synchronous.
• Synchronous transmission requires that all
of the data is sent at the same transfer rate.
• The same number of bits is sent each
second.
• Both computers are synchronized through
the use of an internal clock.
• It is faster and more efficient, but quite
expensive as it requires very stable
connections.

6. • Asynchronous transmission is sent at
varying rates and the flow is regulated
through the use of start and stop bits.
• One of the protocols agreed upon during
handshaking is how many start and stop bits
will be used.
• [Diagram 3.10, p.88]
• Protocols are a set of rules that govern the
transfer of data between two computers.

7. • They define:
• how a link is established
• how data is transmitted
• how errors are detected and corrected
• Numerous protocols have been developed
for different technologies.
• [Table 3.1, p.89 – Do the following: IPX,
X.25, ATM, Kermit, TCP/IP, HTTP, FTP,
POP, MIME]

8. • A network is any number of computers and
their peripheral devices connected together
in some way.
• Each device in a network is called a node.
• Terminals are devices that send data to and
receive data from another computer.
• If the terminal has memory and processing
capabilities it is called an intelligent
terminal.
• Personal computers are often called
workstations on a network.

9. • Networks can be either LAN’s, WAN’s or
very rarely, GAN’s
• Local Area Networks (LAN’s) – are linked
computers at one physical location
• Wide Area Network (WAN’s) – connect
computers over several geographical
locations
• Global Area Networks (GAN’s) –
computers and devices connected all over
the world

10. • Network topology is the physical
arrangement of the devices in a network.
• Three common types of topologies are:
• bus
• star
• ring

11. Bus Network

12. Star Network

13. Ring Network

14. • The bus topology is where all devices are
attached to a direct line called a bus.
• Each devices checks that the line is free and
sends its signal.
• If there is a data collision then the sending
terminal waits a random time then attempts
resending.
• If one node fails the system will still work.
• A star topology has a central computer with
each device connected directly to it.

15. • The central computer receives messages
and sends them to the destination device.
• It requires extra cabling because each
device must be connected to the central
computer.
• If one devices fails, the network will still
function unless it is the central computer
that is broken.
• Its speed is determined by the processing
power of the central computer.

16. • A ring topology is an arrangement where all
devices are attached so that the connection
is a continuous loop.
• Data flow is one direction moving from
device to device.
• A ‘token’ is passed along the network and
data packets are attached to the token and
released when they reach the appropriate
node.

17. • There are a number of ways to deal with
multiple users wanting to access the
network.
• The two most common methods are:
• Ethernet
• token ring
• Ethernet is based upon a bus network.
• Ethernet allows data to be sent in both
directions simultaneously.
• This means there will be data collisions and
errors

18. • To overcome this problem, Ethernet uses a
system called Carrier Sense Multiple
Access and Collision Detection
(CSMA/CD)
• In CSMA/CD all nodes have the ability to
sense signals on a network.
• When a node wishes to transmit, it ‘listens’
for a signal on the bus.
• When no signals are detected, it transmits.
• If two nodes transmit at the same time then
a data collision can occur.

19. • When a collision is detected, each device
stops transmitting, waits a randomly
determined time, then transmits again.
• Token ring is a LAN access protocol based
upon ring topologies.
• Special data packets, called tokens, are
continually passed between nodes on the
network.
• Workstations with data to send attach it to a
free token and transmit it.
• A busy token cannot be used by other
nodes.

20. • When the data is received it is replaced with
an acknowledgement and sent back to the
original sending node.
• There are several special purpose hardware
devices used in a successful network.
• They include:
• a network interface card
• servers
• routers and switches
• bridges and gateways
• hubs

21. • A network interface card (NIC) is an
expansion card that links the network to the
computer motherboard.
• The type of NIC depends upon the type of
network.
• A server is a dedicated computer that
provides services to other computers.
• Workstations log on to the server to give
them access to files, applications or
peripheral devices.

22. • Types of servers include:
• file server
• print server
• mail server
• Internet server
• Networks are often linked to other networks
and this requires paths to be established and
signal strength to be boosted.
• Devices used to determine the path between
networks include routers and switches.

23. • Routers maintain a table of available routes
and their conditions.
• It uses this table to determine the best route
for any given data packet.
• Data packets often travel through several
networks and routers before they reach their
destination.
• A switch is similar, but it does not maintain
a table, therefore making it a simpler and
faster mechanism for passing the message
along.

24. • However, they do not always choose the
faster route for the packet to travel along.
• The actual connection between networks is
achieved through bridges and gateways.
• A bridge is a combination of hardware and
software used to link two similar networks.
• Bridges examine each data packet and
forward any that are addressed to a
connected LAN.
• Gateways are combinations of hardware
and software used to link two different
kinds of network.

25. • This usually involves converting different
protocols.
• A repeater may also be used to increase a
diminishing signal.
• Repeaters are less intelligent than bridges or
gateways.
• A hub is a central connecting device within
a network.
• A hub can be considered passive if it just
channels data or it can contain a router to
improve traffic flow.

26. • As well as the devices connected to a
network, we need to consider the
transmission medium.
• Data is transferred along a transmission
medium.
• The capacity of a transmission medium is
called the bandwidth.
• Bandwidth is generally measured in bps
• They can be categorised as wire or wireless.
• Wire transmission involves wires and
cables.

27. • Twisted pair cable consists of two insulated
copper wires twisted around each other to form
a spiral.
• There are two types:
• shielded twisted pair (STP)
• unshielded twisted pair (UTP)
• STP is more often used in ‘noisy’
environments.
• Twisted pair is the slowest medium with
transmission speeds up to 60 Kbps.

28. • Coaxial cable consists of a single copper wire
surrounded by insulation, shielding , then more
insulation.
• It allows transmission with little interference.
• Generally used for under 2kms.
• Bandwidth is around 10Mbps.
• Fibre-optic cables are made from glass fibres
the width of a human hair, that are often
bundled together.

29. • They are:
• free from interference
• very secure
• able to transmit at high speeds
(> 400 Mbps)
• Most LAN’s use twisted pair or coaxial cable
as fibre-optic is too expensive but this is
changing and fibre-optic is becoming much
more common.

30. • There are two types of transmission used:
• baseband
• broadband
• Baseband uses the entire capacity of the cable to
transmit one signal.
• Broadband networks divide the cable so that
several signals can be transmitted simultaneously.
• Most LAN’s are baseband.
• Wireless transmission moves data without a
physical connection.

31. • Wireless includes:
• microwaves
• radio frequencies (RF)
• infra-red (IR)
• satellites
• A microwave is a high frequency radio signal
that requires antennae no further than 50 km
apart.
• It is faster than coaxial or regular telephone
lines and relatively error-free.

32. • Radio frequencies are used for many home and
business wireless networks, usually in the 2.4
GHz range.
• Can have an access point (or hot-spot) or be
done in an ad-hoc manner.
• Satellites can transmit large amounts of data
over large distances.
• Used by major corporations, television
networks and telecommunications.
• IR is used by some devices in LAN’s

33. • Each computer in a network must have
appropriate network software.
• This software is usually organised by a
network administrator.
• Their responsibilities include:
• network security
• software installations and updates
• monitoring daily activity
• enforcing licensing agreements
• developing a storage solution
• performing routine backups

34. • A network operating system (NOS) is an
operating system designed to support
networked computers.
• One part resides on each node with another
part on the server.
• Tasks carried out by a network OS include:
• administration
• file management
• applications
• resource management
• security

35. • An intranet is a private network that uses a
similar interface to the Web.
• It consists of many interlinked LANs.
• It provides access similar to the Internet, but
only to a select group of users (e.g. employees,
students)
• Firewalls monitor the flow of data in both
directions to maintain the security of the
organisation.

36. • An extranet is an intranet that is accessible to
customers, suppliers or others outside the
organisation.
• It provides such information as product
descriptions, answers to frequently asked
questions, warranties and how to contact
customer service.
• Extranets are still limited to accessing select
computer paths and files.