For the students admitted from the Academic year 2012-2013(R 2012) 
Sri Ramakrishna Engineering College, Coimbatore-22 
De...
For the students admitted from the Academic year 2012-2013(R 2012) 
Semester V Electrical and Electronics Engineering Mark...
For the students admitted from the Academic year 2012-2013(R 2012) 
Semester VII Electrical and Electronics Engineering Ma...
For the students admitted from the Academic year 2012-2013(R 2012) 
Group Code No. Course Title L T P C CA FE Total 
Group...
For the students admitted from the Academic year 2012-2013(R 2012) 
SEMESTER III 
12MA2301 TRANSFORMS AND PARTIAL DIFFEREN...
For the students admitted from the Academic year 2012-2013(R 2012) 
1. Kandasamy.P.,Thilagavathy.K., and Gunavathy.K., “En...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2302 ANALYSIS AND SYNTHESIS OF ELECTRICAL NETWORKS...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2303 ELECTROMAGNETIC FIELD THEORY 3 1 0 4 
AIM 
Th...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2304 MEASUREMENTS AND INSTRUMENTATION 3 0 0 3 
AIM...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2305 ANALOG ELECTRONIC CIRCUITS 3 0 0 3 
AIM 
To i...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2306 DIGITAL PRINCIPLES AND DESIGN 3 0 0 3 
AIM 
T...
For the students admitted from the Academic year 2012-2013(R 2012) 
5. Jain R.P., “Modern Digital Electronics”, Tata McGra...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2307 MEASUREMENT AND INSTRUMENTATION LABORATORY 0 ...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2308 ELECTRONIC CIRCUITS LABORATORY 0 0 3 2 
AIM 
...
For the students admitted from the Academic year 2012-2013(R 2012) 
SEMESTER IV 
12MA2001 NUMERICAL METHODS 3 1 0 4 
AIM 
...
For the students admitted from the Academic year 2012-2013(R 2012) 
1. Veerarajan.T., “Numerical Methods”, Tata McGraw Hil...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2402 DC MACHINES AND TRANSFORMERS 3 1 0 4 
AIM 
To...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2403 TRANSMISSION AND DISTRIBUTION OF ELECTRICAL E...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2404 IC FABRICATION AND LINEAR INTEGRATED CIRCUITS...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2405 INTRODUCTION TO SIGNALS AND SYSTEMS 3 1 0 3 
...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2406 PRINCIPLES OF COMMUNICATION ENGINEERING 3 0 0...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2407 DC MACHINES AND TRANSFORMERS LABORATORY 0 0 3...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2408 LINEAR INTEGRATED CIRCUITS LABORATORY 0 0 3 2...
For the students admitted from the Academic year 2012-2013(R 2012) 
V SEMESTER 
12EE2501 CONTROL SYSTEM ENGINEERING 3 1 0 ...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2502 SYNCHRONOUS AND INDUCTION MACHINES 3 1 0 4 
A...
For the students admitted from the Academic year 2012-2013(R 2012) 
Page 26 of 85
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2503 POWER SYSTEM PROTECTION AND SWITCHGEAR 3 0 0 ...
For the students admitted from the Academic year 2012-2013(R 2012) 
3. Paithankar Y.G., and Bhide S.R., “Fundamentals of P...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2504 MICROPROCESSORS AND MICRO CONTROLLERS 3 0 0 3...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2505 DIGITAL SIGNAL PROCESSING FOR ELECTRICAL ENGI...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2506 DATA STRUCTURES AND DEVELOPING ALGORITHMS 3 0...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2507 SYNCHRONOUS AND INDUCTION MACHINES LABORATORY...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2508 DATA STRUCTURES AND ALGORITHMS LABORATORY 0 0...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EN2001 COMMUNICATION SKILLS LABORATORY 0 0 2 1 
AIM ...
For the students admitted from the Academic year 2012-2013(R 2012) 
Why is GD part of selection process? - Structure of a ...
For the students admitted from the Academic year 2012-2013(R 2012) 
VI SEMESTER 
12EE2601 ELECTRIC MACHINE DESIGN 3 1 0 4 ...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2602 POWER SYSTEM ANALYSIS 3 1 0 4 
AIM 
To become...
For the students admitted from the Academic year 2012-2013(R 2012) 
1. Kundur P, “Power System Stability and Control, Tata...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2603 POWER ELECTRONICS 3 1 0 4 
AIM 
To introduce ...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2604 EMBEDDED SYSTEM DESIGN 3 0 0 3 
AIM 
To under...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2605 MANAGEMENT CONCEPTS AND PRACTICES 3 0 0 3 
AI...
For the students admitted from the Academic year 2012-2013(R 2012) 
REFERENCES 
1. Porter Michael, “Competitive Advantage”...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2607 CONTROL SYSTEMS LABORATORY 0 0 3 2 
AIM 
To p...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2608 DSP AND MICROPROCESSORS LABORATORY 0 0 3 2 
A...
For the students admitted from the Academic year 2012-2013(R 2012) 
VII SEMESTER 
12EE2701 ELECTRIC ENERGY GENERATION, UTI...
For the students admitted from the Academic year 2012-2013(R 2012) 
3. Wadhwa C.L, “Generation, Distribution and Utilizati...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2702 ELECTRIC DRIVES AND CONTROL 3 0 0 3 
AIM 
To ...
For the students admitted from the Academic year 2012-2013(R 2012) 
12EE2703 POWER SYSTEM ECONOMICS AND CONTROL TECHNIQUES...
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
SYLLABUS OF 2012 BATCHES
Próxima SlideShare
Cargando en…5
×

SYLLABUS OF 2012 BATCHES

1.984 visualizaciones

Publicado el

THIS SYLLABUS IS THE VERY USEFUL FOR STUDENTS .

Publicado en: Ingeniería
0 comentarios
0 recomendaciones
Estadísticas
Notas
  • Sé el primero en comentar

  • Sé el primero en recomendar esto

Sin descargas
Visualizaciones
Visualizaciones totales
1.984
En SlideShare
0
De insertados
0
Número de insertados
1
Acciones
Compartido
0
Descargas
22
Comentarios
0
Recomendaciones
0
Insertados 0
No insertados

No hay notas en la diapositiva.

SYLLABUS OF 2012 BATCHES

  1. 1. For the students admitted from the Academic year 2012-2013(R 2012) Sri Ramakrishna Engineering College, Coimbatore-22 Department of Electrical and Electronics Engineering Regulations: 2012 Curriculum Semester III Electrical and Electronics Engineering Marks Code No. Course Title L T P C CA FE Total THEORY 12MA2301 Transforms and Partial Differential Equations 3 1 0 4 20 80 100 12EE2302 Analysis and Synthesis of Electrical Networks 3 1 0 4 20 80 100 12EE2303 Electromagnetic Field Theory 3 1 0 4 20 80 100 12EE2304 Measurements and Instrumentation 3 0 0 3 20 80 100 12EE2305 Analog Electronic Circuits 3 0 0 3 20 80 100 12EE2306 Digital Principles and Design 3 0 0 3 20 80 100 PRACTICALS 12EE2307 Measurements and Instrumentation Laboratory 0 0 3 2 20 80 100 12EE2308 Electronic Circuits Laboratory 0 0 3 2 20 80 100 Total 18 3 6 25 - - - Semester IV Electrical and Electronics Engineering Marks Code No. Course Title L T P C CA FE Total THEORY 12MA2001 Numerical Methods 3 1 0 4 20 80 100 12EE2402 DC Machines and Transformers 3 1 0 4 20 80 100 12EE2403 Transmission & Distribution of Electrical Energy 3 0 0 3 20 80 100 12EE2404 IC Fabrication and Linear Integrated Circuits 3 0 0 3 20 80 100 12EE2405 Introduction to Signals and Systems 3 0 0 3 20 80 100 12EE2406 Principles of Communication Engineering 3 0 0 3 20 80 100 PRACTICALS 12EE2407 DC Machines and Transformers Laboratory 0 0 3 2 20 80 100 12EE2408 Linear Integrated Circuits Laboratory 0 0 3 2 20 80 100 Total 18 2 6 24 - - - Page 1 of 85
  2. 2. For the students admitted from the Academic year 2012-2013(R 2012) Semester V Electrical and Electronics Engineering Marks Code No. Course Title L T P C CA FE Total THEORY 12EE2501 Control System Engineering 3 1 0 4 20 80 100 12EE2502 Synchronous and Induction Machines 3 1 0 4 20 80 100 12EE2503 Power System Protection & Switchgear 3 0 0 3 20 80 100 12EE2504 Microprocessors and Microcontrollers 3 0 0 3 20 80 100 12EE2505 Digital Signal Processing for Electrical Engineers 3 0 0 3 20 80 100 12EE2506 Data Structures and Developing Algorithms 3 0 0 3 20 80 100 PRACTICALS 12EE2507 Synchronous and Induction Machines Laboratory 0 0 3 2 20 80 100 12EE2508 Data Structures and Algorithms Laboratory 0 0 3 2 20 80 100 12EN2001 Communication skills laboratory 0 0 2 1 20 80 100 Total 18 2 8 25 - - - Semester VI Electrical and Electronics Engineering Marks Code No. Course Title L T P C CA FE Total THEORY 12EE2601 Electric Machine Design 3 1 0 4 20 80 100 12EE2602 Power System Analysis 3 1 0 4 20 80 100 12EE2603 Power Electronics 3 1 0 4 20 80 100 12EE2604 Embedded System Engineering 3 0 0 3 20 80 100 12EE2605 Management Concepts and Practices 3 0 0 3 20 80 100 Elective I 3 0 0 3 20 80 100 PRACTICALS 12EE2607 Control Systems Laboratory 0 0 3 2 20 80 100 12EE2608 DSP and Microprocessors Laboratory 0 0 3 2 20 80 100 Total 18 3 6 25 - - - Page 2 of 85
  3. 3. For the students admitted from the Academic year 2012-2013(R 2012) Semester VII Electrical and Electronics Engineering Marks Code No. Course Title L T P C CA FE Total THEORY 12EE2701 Electric Energy- Generation, Utilisation and Conservation 3 0 0 3 20 80 100 12EE2702 Electric Drives and Controls 3 0 0 3 20 80 100 12EE2703 Power System Economics and Control Techniques 3 1 0 4 20 80 100 12ME2001 Total Quality Management 3 0 0 3 20 80 100 Elective II 3 0 0 3 20 80 100 Elective III 3 0 0 3 20 80 100 PRACTICALS 12EE2707 Power Electronics and Drives Laboratory 0 0 3 2 20 80 100 12EE2708 Power System Simulation Laboratory 0 0 3 2 20 80 100 12EE2709 Comprehensive Viva Voce 0 0 2 1 100 100 Total 18 1 8 24 - - - Semester VIII Electrical and Electronics Engineering Marks Code No. Course Title L T P C CA FE Total THEORY Elective IV 3 0 0 3 20 80 100 Elective V 3 0 0 3 20 80 100 Elective VI 3 0 0 3 20 80 100 PRACTICALS 12EE2804 Project Work 0 0 18 6 20 80 100 Total 9 0 18 15 - - - Electives Electrical and Electronics Engineering Marks Page 3 of 85
  4. 4. For the students admitted from the Academic year 2012-2013(R 2012) Group Code No. Course Title L T P C CA FE Total Group I 12CS2001 Java Programming 3 0 0 3 20 80 100 12EE2E01 Introduction to Data Base Management System 3 0 0 3 20 80 100 12EE2E02 DSP based System Design 3 0 0 3 20 80 100 12EE2E03 Introduction to Computer Architecture 3 0 0 3 20 80 100 Group II 12EE2E04 LabView and Virtual Instrumentation 3 0 0 3 20 80 100 12EE2E05 Power Quality 3 0 0 3 20 80 100 12EE2E06 Transients in Power System 3 0 0 3 20 80 100 12EE2E07 Networking in Smart Grids 3 0 0 3 20 80 100 12EE2E08 Soft Computing Techniques 3 0 0 3 20 80 100 12EE2E09 EHV AC and DC Power Transmission 3 0 0 3 20 80 100 12EE2E10 Digital System Design 3 0 0 3 20 80 100 12EE2E11 Analog VLSI Design 3 0 0 3 20 80 100 Group III 12EE2E12 Electronic Product Design 3 0 0 3 20 80 100 12EE2E13 Computer Aided Design of Electrical Apparatus 3 0 0 3 20 80 100 12EE2E14 High Voltage Engineering 3 0 0 3 20 80 100 12EE2E15 Opto Electronics 3 0 0 3 20 80 100 12EE2E16 Nano Science 3 0 0 3 20 80 100 12EE2E17 Distributed Control System 3 0 0 3 20 80 100 12EE2E18 Flexible AC Transmission Systems 3 0 0 3 20 80 100 12EE2E19 AI Applications to Power Systems 3 0 0 3 20 80 100 12EE2E20 Robotics Technology and Flexible Automation 3 0 0 3 20 80 100 12EE2E21 Special Electrical Machines 3 0 0 3 20 80 100 12EE2E22 Non-conventional Energy Sources 3 0 0 3 20 80 100 12IT2002 Soft Skills 3 0 0 3 20 80 100 12IT2004 Business Intelligence and its Applications 3 0 0 3 20 80 100 Total credits for the Course - 190 L : Lecture *CA : Continuous assessment T : Tutorial *FE : Final Examination P : Practical C : Credits Criterion for passing: · Minimum Marks (FE) : 50/100 (In the Final Examination) · Minimum Marks (CA+FE) : 50 Page 4 of 85
  5. 5. For the students admitted from the Academic year 2012-2013(R 2012) SEMESTER III 12MA2301 TRANSFORMS AND PARTIAL DIFFERENTIAL EQUATIONS 3 1 0 4 (Common to all branches of Engineering and Technology except BME) AIM The course aims to develop the skills of the students in the areas of Partial differential equations, Boundary value problems and Transform techniques. This will be necessary for their effective studies in a large number of engineering subjects like heat conduction, communication systems, electro optics and electromagnetic theory. OBJECTIVES At the end of the course the students would · Be capable of mathematically formulating certain practical problems in terms of partial differential equations, solve them and physically interpret the results. · Have gained the knowledge of Fourier series, their different possible forms and the frequently needed practical harmonic analysis that an engineer may have to make from discrete data. · Have obtained capacity to formulate and identify certain boundary value problems encountered in engineering practices, decide on applicability of the Fourier series method of solution, solve them and interpret the results. · Have grasped the concept of expression of a function, under certain conditions, as a double integral leading to identification of transform pair, and specialization on Fourier transform pair, their properties, the possible special cases with attention to their applications. · Have learnt the basics of Z-Transform in its applicability to discretely varying functions, gained the skill to formulate certain problems in terms of difference equations and solve them. UNIT- I PARTIAL DIFFERENTIAL EQUATIONS 12 Formation of partial differential equations by elimination of arbitrary constants and arbitrary functions – Solution of of first order partial differential equations of the forms F(p,q) = 0, Z= px + qy + F(p,q) and F(z,p,q) = 0 – Lagrange’s linear equation – Linear partial differential equations of second and higher order with constant coefficients. UNIT- II FOURIER SERIES 12 Dirichlet’s conditions – General Fourier series – Odd and Even functions – Half range sine series and cosine series – Parseval’s identity – Harmonic Analysis. UNIT- III BOUNDARY VALUE PROBLEMS 12 Classification of second order quasi linear partial differential equations – Solutions of one dimensional wave equation (Problems only) – One dimensional heat equation (Problems only) -Steady state solution of two-dimensional heat equation in Cartesian coordinates (Insulated edges excluded) Problems only. UNIT- IV FOURIER TRANSFORMS 12 Fourier integral theorem (without proof) – Fourier transform pair - Sine and Cosine transforms – Properties– Transforms of simple functions – Convolution theorem – Parseval’s identity. UNIT- V Z -TRANSFORMS AND DIFFERENCE EQUATIONS 12 Z-transform– Elementary properties– Inverse Z-transform– Convolution theorem– Formation of difference equations (Direct problems only) – Solution of difference equations using Z - Transform. Total Periods (45+15T): 60 TEXT BOOKS Page 5 of 85
  6. 6. For the students admitted from the Academic year 2012-2013(R 2012) 1. Kandasamy.P.,Thilagavathy.K., and Gunavathy.K., “Engineering Mathematics’’, S. Chand & Company ltd., Volume II, New Delhi, 2011. 2. Grewal.B.S., “Higher Engineering Mathematics”, Khanna Publishers, 40th Edition, New Delhi, 2008. REFERENCE BOOKS 1. Wylie C. Ray and Barrett Louis.C., “Advanced Engineering Mathematics”, McGraw-Hill, Inc., 6thEdition, New York, 1995. 2. Andrews.L.A., and Shivamoggi B.K., “Integral Transforms for Engineersand Applied Mathematicians”, Macmillen , 1st Edition, New York ,1988. 3. Churchill.R.V. and Brown.J.W., “Fourier Series and Boundary Value Problems”, McGraw-Hill Book Co., 4th Edition, Singapore,1987. Page 6 of 85
  7. 7. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2302 ANALYSIS AND SYNTHESIS OF ELECTRICAL NETWORKS 3 1 0 4 AIM To provide depth knowledge on network analysis and synthesis concepts OBJECTIVES · To understand the concepts of graph theory · To learn about two port networks · To study about network functions of one port and two port networks · To understand the concept of network synthesis · To study about active and passive filters UNIT – I GRAPH THEORY 12 Graph of a Network – Definitions – Tree - Co tree – Link - Basic loop and basic cut set - Incidence matrix - Cut set matrix - Tie set matrix – Duality - Loop and Nodal methods of analysis. UNIT – II TWO PORT NETWORKS 12 Characterization of LTI two port networks – Z, Y, ABCD and h parameters - Reciprocity and symmetry – Inter relationships between the parameters - Inter-connections of two port networks - Ladder and Lattice networks - T & I Representation. UNIT – III NETWORK FUNCTIONS 12 Concept of Complex frequency, Transform Impedances Network functions of one port and two port networks, concept of poles and zeros, properties of driving point and transfer functions, time response and stability from pole zero plot. UNIT – IV NETWORK SYNTHESIS 12 Positive real functions - definition and properties- properties of RL, RC & LC - pointing functions-synthesis of RL, RC, LC driving point admittance functions using Foster and Cauer first and second forms. UNIT – V FILTERS 12 Image parameters and characteristics impedance- Passive and active filters fundamentals - Low pass filters- High pass filters - Constant K type filters- Introduction to active & passive filters. Total Periods (45 +15T): 60 TEXT BOOKS 1. Van – Valkenburg M.E., “Network Analysis”, Prentice Hall of India, 3rd Edition, New Delhi, 2011. 2. Sudhakar A., and Shyammohan, “Circuits and Networks Analysis and Synthesis”, Tata McGraw Hill Publishing Co. Ltd., 3rd Edition, New Delhi, 2007. REFERENCES 1. Chakrabati A, “Circuits Theory (Analysis and synthesis)”, Dhanpath Rai & Sons, New Delhi, 1999. 2. Van Valkenburg M.E., “Introduction to Modern Network Synthesis”, Wiley Eastern Limited, 1999. 3. Jagan N.C., and Lakshminarayanan C., “ Network Analysis”, B.S.Publications, 2008. 4. Suresh Kumar K.S.,”Electric Circuits and Networks”, Pearson Education, 2009. Page 7 of 85
  8. 8. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2303 ELECTROMAGNETIC FIELD THEORY 3 1 0 4 AIM This subject aims to provide the student an understanding of the fundamentals of electromagnetic fields and their applications in electrical engineering. OBJECTIVES To impart knowledge on · Sources and effects of electromagnetic fields. · Concepts of electrostatics, electrical potential, energy density and their applications. · Concepts of magnetostatics, magnetic flux density, scalar and vector potential and its applications. · Faraday’s laws, induced emf and their applications. · Concepts of electromagnetic waves and pointing vector. UNIT- I INTRODUCTION 12 Sources and effects of electromagnetic fields – Vector fields – Different co-ordinate systems – Vector calculus – Gradient, Divergence and Curl - Divergence theorem – Stoke’s theorem. UNIT - II ELECTROSTATICS 12 Coulomb’s Law – Electric field intensity – Field due to point and continuous charges – Gauss’s law and application – Electrical potential – Electric field and equipotential plots – Electric field in free space, conductors, dielectric – Dielectric polarization, Electric field in multiple dielectrics – Boundary conditions, Poisson’s and Laplace’s equations – Capacitance-Energy density – Dielectric strength. UNIT - III MAGNETOSTATICS 12 Lorentz Law of force, magnetic field intensity – Biot–savart Law - Ampere’s Law – Magnetic field due to straight conductors, circular loop, infinite sheet of current – Magnetic flux density (B) – B in free space, conductor, magnetic materials – Magnetization – Magnetic field in multiple media – Boundary conditions – Scalar and vector potential – Magnetic force – Torque – Inductance – Energy density – Magnetic circuits. UNIT - IV ELECTRODYNAMIC FIELDS 12 Faraday’s laws, induced emf – Transformer and motional EMF, Maxwell’s equations (differential and integral forms) – Displacement current – Relation between field theory and circuit theory. UNIT - V ELECTROMAGNETIC WAVES 12 Generation – Electro Magnetic Wave equations – Wave parameters; velocity, intrinsic impedance, propagation constant – Waves in free space, lossy and lossless dielectrics, conductors-skin depth, Poynting vector – Plane wave reflection and refraction. Total Periods (45 +15T): 60 TEXT BOOKS 1. William .H. Hayt, “Engineering Electromagnetics”, Tata McGraw Hill, 7th Edition, 2006. 2. Gangadhar K.A, “Field Theory”, Khanna Publishers, 13th Edition, New Delhi, 1997. REFERENCES 1. John.D.Kraus, “Electromagnetics”, McGraw Hill book Co., 4th Edition, New York, 1992. 2. Joseph. A.Edminister, “Theory and Problems of Electromagnetics”, Schaum Series, Tata McGraw Hill, 2nd Edition, 2006. 3. Kraus and Fleish, “Electromagnetics with Applications”, McGraw Hill International Editions, 5th Edition, 1999. 4. Mathew N.O.Sadiku, ‘Elements of Electromagnetics’, 3rd Edition, Oxford University Press, 2003. Page 8 of 85
  9. 9. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2304 MEASUREMENTS AND INSTRUMENTATION 3 0 0 3 AIM To provide adequate knowledge in electrical instruments and measurements techniques. OBJECTIVES · To make the student have a clear knowledge of the basic laws governing the operation of the instruments, relevant circuits and their working. · Introduction to general instrument system, error, calibration etc. Emphasis is laid on analog and digital techniques used to measure voltage, current, energy and power etc. · To have an adequate knowledge of comparison methods of measurement. · Elaborate discussion about storage & display devices. · Exposure to various transducers and data acquisition system. UNIT - I INTRODUCTION 9 Functional elements of an instrument – Static and dynamic characteristics – Errors in measurement – Statistical evaluation of measurement data – Primary and secondary standards - Calibration. UNIT - II ELECTRICAL AND ELECTRONICS INSTRUMENTS 9 Principle and types of analog and digital voltmeters, ammeters, multimeters – Average ,RMS and peak responding type meters- Digital Phase meter- Single and three phase wattmeters and energy meters – Magnetic measurements – Determination of B-H curve and measurements of iron loss – Instrument transformers – Instruments for measurement of frequency and phase- Power factor meters. UNIT - III COMPARISON METHODS OF MEASUREMENTS 9 D.C. & A.C. potentiometers - D.C & A.C bridges - transformer ratio bridges - self-balancing bridges. Interference & screening – Multiple earth and earth loops - Electrostatic and electromagnetic interference – Grounding techniques. UNIT - IV STORAGE AND DISPLAY DEVICES 9 Magnetic disk and tape – Recorders, digital plotters and printers (qualitative treatment only), LED, LCD & dot matrix display – DSO, MSO, Digital transceiver recorder, Power measurement and analysis, Real time spectrum analysers. UNIT - V TRANSDUCERS AND DATA ACQUISITION SYSTEM 9 Classification of transducers – Selection of transducers – Resistive, capacitive & inductive transducers – Piezoelectric, optical and digital transducers – Elements of data acquisition system – A/D, D/A converters. Total periods: 45 TEXT BOOKS 1. Doebelin E.O., “Measurement Systems – Application and Design”, Tata McGraw Hill publishing company, 5th Edition, 2006. 2. Sawhney, A.K. “A Course in Electrical & Electronic Measurements & Instrumentation”, Dhanpat Rai and Co, 2004. REFERENCES 1. Golding,E.W., and Widdis,F.C., “Electrical Measurements and Measuring Instruments”, A H Wheeler & Company, 5th Edition, 2003. 2. Kalsi H.S., ‘Electronic Instrumentation’, Tata McGraw Hill publishing company, 2nd Edition, New Delhi, 2004. 3. Bouwens, A.J. “Digital Instrumentation’, Tata McGraw Hill Publishing Company, 1997. 4. Moorthy, D.V.S. “Transducers and Instrumentation, Prentice Hall of India Pvt Ltd, 2003. 5. Martin Reissland, ‘Electrical Measurements’, New Age International (P) Ltd., Delhi, 2001. 6. Gupta, J. B. “A Course in Electronic & Electrical Measurements”, Kataria & Sons, Delhi, 2003. Page 9 of 85
  10. 10. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2305 ANALOG ELECTRONIC CIRCUITS 3 0 0 3 AIM To introduce the concept of realizing circuits using active and passive devices for signal generation and amplification. OBJECTIVES · To learn and analyse the process of AC to DC conversion. · To expose the students to study the different biasing and configurations of the amplifier circuits. · To study the characteristics of tuned amplifier. · To expose the students to various amplifiers and oscillator circuits with feedback concepts. · To learn the wave shaping process and circuits. UNIT - I RECTIFIERS AND POWER SUPPLY CIRCUITS 9 Half wave & full wave rectifier analysis - Inductor filter – Capacitor filter - Series voltage regulator – Switched mode power supply. UNIT - II TRANSISTOR BIASING AND AMPLIFIERS 9 Need for biasing-Types of biasing-Fixed and self biasing of BJT & FET – Stability factor - Fixed bias circuit, Load line and quiescent point analysis. Small signal analysis of CE, CC & Common source amplifiers – Cascade and Darlington connections, transformer coupled class A, B & AB amplifiers – Push-pull amplifiers. UNIT - III DIFFERENTIAL AND TUNED AMPLIFIERS 9 Differential amplifiers – Common mode and differential mode analysis - DC and AC analysis - Characteristics of tuned amplifiers – Single & double tuned amplifier. UNIT - IV FEEDBACK AMPLIFIER AND OSCILLATOR 9 Characteristics of negative feedback amplifiers – Voltage / current, series/shunt feedback – Theory of sinusoidal oscillators – Hartley, Colpitts, and crystal oscillators - Phase shift and Wien bridge oscillators. UNIT - V WAVE SHAPING CIRCUITS AND OSCILLATORS 9 RC wave shaping circuits – Diode clampers and clippers – Multivibrators – Schmitt triggers – Barkhausen’s criterion for Oscillation- UJT based saw tooth oscillators. Total periods: 45 TEXT BOOKS 1. David A. Bell, “Electronic Devices & Circuits”, Prentice Hall of India/Pearson Education, 4th Edition, Eighth printing, 2004. 2. Jacob Millman & Christos.C.Halkias, “Integrated Electronics: Analog and Digital Circuits and System”, Tata McGraw Hill, 2002. REFERENCES 1. Robert. L. Boylestad & Lo Nashelsky, “Electronic Devices & Circuit Theory”, 8th Edition, Pearson Education, 2002 / PHI. 2. Jacob Millman & Herbert Taub, “Pulse, Digital & Switching Waveforms”, Tata McGraw Hill Publishing Co, 2nd Edition, New Delhi, 2008. 3. Donald L.Schilling and Charles Belove, “Electronic Circuits”, Tata McGraw Hill Publishing Co., 3rd Edition, 2003. 4. Floyd, “Electronic Devices”, Pearson Education India, 7th Edition, New Delhi, 2005. Page 10 of 85
  11. 11. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2306 DIGITAL PRINCIPLES AND DESIGN 3 0 0 3 AIM To introduce the fundamentals of digital circuits, combinational and sequential circuits. OBJECTIVES · To study various number systems and to simplify the mathematical expressions using Boolean functions – simple problems. · To study implementation of combinational circuits · To study the design of various synchronous and asynchronous circuits. · To expose the students to various memory devices. UNIT - I NUMBER SYSTEM & BOOLEAN ALGEBRA 9 Binary, Octal, Decimal, Hexadecimal - Number base conversions – 1’s and 2’s complements - Signed Binary numbers - Binary Arithmetic - Binary codes: Weighted – BCD - 2421- Gray code -Excess 3 code - ASCII – Error detecting and correcting codes - De-Morgan’s Theorem- Principle of Duality- Boolean expression – Boolean function - Minimization of Boolean expressions – Sum of Products (SOP) – Product of Sums (POS) – Minterm – Maxterm - Karnaugh map Minimization – Don’t care conditions - Quine McCluskey method. UNIT - II COMBINATIONAL CIRCUITS 9 Logic Gates: AND, OR, NOT, NAND, NOR, Exclusive-OR and Exclusive-NOR - Implementations of Logic Functions using gates, NAND, NOR – Combinational circuits: Adder- Subtractor – Serial adder/ Subtractor - Parallel adder / Subtractor- Carry look ahead adder- BCD adder- Magnitude Comparator- Multiplexer/ Demultiplexer- Encoder / decoder – Parity Generator/Checker – code converters. UNIT - III SYNCHRONOUS SEQUENTIAL CIRCUITS 9 Latches and Flip flops SR, JK, T, D and Master slave – Characteristic table and equation –Application table – Edge triggering –Level Triggering –Realization of one flip flop using other flip flops –Asynchronous / Ripple counters – Synchronous counters –Modulo – n counter – Classification of sequential circuits: Moore and Mealy circuits - Design of Synchronous counters: state diagram- State table –State minimization –State assignment – Register: shift registers- Universal shift register. UNIT - IV ASYNCHRONOUS SEQUENTIAL CIRCUIT 9 Design of fundamental mode and pulse mode circuits – primitive state / flow table – Minimization of primitive state table –state assignment – Excitation table – Excitation map - cycles – Races – Hazards: Static –Dynamic – Essential – Hazards elimination. UNIT - V PROGRAMMABLE LOGIC DEVICES, MEMORY AND LOGIC FAMILIES 9 Memories: ROM, PROM, EPROM, PLA, PAL and FPGA - Digital logic families: TTL, ECL and CMOS. Total periods: 45 TEXT BOOKS 1. Morris Mano M., “Digital Design”, Pearson Education Inc., 4th Edition, New Delhi, 2008. 2. John.M Yarbrough, “Digital Logic Applications and Design”, Vikas publishing house, New Delhi, 2006. REFERENCES 1. Salivahanan S. and Arivazhagan S., “Digital Circuits and Design”, Vikas Publishing House Pvt. Ltd, 4th Edition, New Delhi, 2004. 2. Thomas L. Floyd, “Digital Fundamentals”, Pearson Education Inc., 10th Edition, New Delhi, 2008. 3. Charles H.Roth. “Fundamentals of Logic Design”, Thomson Publication Company, 2003. 4. Donald P.Leach and Albert Paul Malvino, “Digital Principles and Applications”, Tata McGraw Hill Publishing Company Limited, 5th Edition, New Delhi, 2003. Page 11 of 85
  12. 12. For the students admitted from the Academic year 2012-2013(R 2012) 5. Jain R.P., “Modern Digital Electronics”, Tata McGraw–Hill publishing company limited,3rd Edition, New Delhi, 2003. Page 12 of 85
  13. 13. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2307 MEASUREMENT AND INSTRUMENTATION LABORATORY 0 0 3 2 AIM The aim of this lab is to fortify the students with an adequate work experience in the measurement of different quantities and also the expertise in handling the instruments involved. OBJECTIVES To train the students in the measurement of displacement, resistance, inductance, torque and angle etc., and to give exposure to AC, DC bridges and transient measurement. 1. Study of displacement and pressure transducers 2. Measurement of high resistance using Kelvin’s double bridge and Megger 3. Measurement of frequency using Wien bridge 4. To study dielectric behavior (using Schering bridge and standard capacitor) 5. Measurement of inductance using maxwell’s bridge 6. Instrumentation amplifiers 7. Measurement of transients using DSO 8. Calibration of single-phase energy meter 9. Calibration of current transformer (both measurement and protection) 10. Measurement of three phase power and power factor 11. Measurement of iron loss 12. Measurement systems using LabVIEW and MATLAB 13. Design and construction of resistive and capacitive dividers Practical 45 Page 13 of 85
  14. 14. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2308 ELECTRONIC CIRCUITS LABORATORY 0 0 3 2 AIM This laboratory aims to train the students in both analog and digital electronics circuits so that they can acquire practical knowledge in electronics. 1. Single Phase Half and Full wave rectifier with inductive and capacitive filters. 2. RC coupled and differential amplifier. 3. Frequency response of common emitter amplifiers. 4. RC Phase shift, Hartley, Colpitts oscillators 5. Astable / Monostable multivibrator 6. Series voltage regulator. 7. Study of Basic Digital gates. (Verification of truth table for AND, OR, EXOR, NOT, NOR, NAND, JK FF, RS FF, D FF) 8. Implementation of Boolean Functions, Adder/ Subtractor circuits 9. Code converters, Parity generator and parity checking, Excess 3, 2s Complement, Binary to grey code using suitable IC’s. 10. Encoders and Decoders 11. Multiplexer/ De-multiplexer: Study of 4:1; 8:1 multiplexer and Study of 1:4; 1:8 Demultiplexer 12. Shift Registers: Design and implementation of 4-bit shift registers in SISO, SIPO, PISO, PIPO modes using suitable IC’s. Practical 45 Page 14 of 85
  15. 15. For the students admitted from the Academic year 2012-2013(R 2012) SEMESTER IV 12MA2001 NUMERICAL METHODS 3 1 0 4 AIM With the present development of the computer technology, it is necessary to develop efficient algorithms for solving problems in Science, Engineering and Technology. OBJECTIVES At the end of the course, the students would be acquainted with the basic concepts in numerical methods and their uses are summarized as follows · The solution of nonlinear (algebraic or transcendental) equations, system of linear equations and eigen value problem of matrix can be obtained numerically where analytical methods fail to give solution. · When huge amounts of experimental data are involved, the methods discussed on interpolation will be useful in constructing approximate polynomial to represent the data and to find the intermediate values. · The numerical differentiation and integration find application when the function in the analytical form is too complicated or the huge amounts of data are given. · The methods introduced in the solution of ordinary differential equations and partial differential equations will be useful in attempting any engineering problem. UNIT- I SOLUTION OF EQUATIONS AND EIGENVALUE PROBLEMS 12 Solution of algebraic and transcendental equations– Regula-Falsi method– Newton’s method– Solution of linear system by Gaussian elimination and Gauss-Jordon methods– Inverse of a matrix by Gauss Jordon method - Iterative methods: Gauss Jacobi and Gauss-Seidel methods – Eigen value of a matrix by power method. UNIT-II INTERPOLATION AND APPROXIMATION 12 Newton’s forward and backward interpolation– Lagrange’s interpolation– Newton’s divided difference interpolation – Interpolating with a cubic spline UNIT-III NUMERICAL DIFFERENTIATION AND INTEGRATION 12 Derivatives using Newton’s forward and backward interpolation– Numerical integration by trapezoidal and Simpson’s 1/3 and 3/8 rules- Romberg’s method– Two and Three point Gaussian quadrature formula– Double integrals using trapezoidal and Simpson’s rule. UNIT-IV INITIAL VALUE PROBLEMS FOR ORDINARY DIFFERENTIAL EQUATIONS 12 Single step methods: Taylor series method– Euler and modified Euler methods– Fourth order Runge– Kutta method for solving first and second order equations– Multistep methods: Milne’s and Adam’s predictor and corrector methods. UNIT-V BOUNDARY VALUE PROBLEMS IN ORDINARY AND PARTIAL DIFFERENTIAL EQUATIONS 12 Finite difference solution of second order ordinary differential equation– Finite difference solution of one dimensional heat equation by explicit and implicit methods– One dimensional wave equation and two dimensional Laplace and Poisson equations. Total Periods (45+15T): 60 TEXT BOOKS 1. Gerald.C.F. andWheatley.P.O. “Applied Numerical Analysis”, Pearson Education Asia, 6th Edition, New Delhi, 2002. 2. Kandasamy.P., Thilagavathy.K. andGunavathy.K., “Numerical Methods”, S.Chand Co. Ltd., 3rd Edition, New Delhi, 2010. REFERENCE BOOKS Page 15 of 85
  16. 16. For the students admitted from the Academic year 2012-2013(R 2012) 1. Veerarajan.T., “Numerical Methods”, Tata McGraw Hill Pub.Co.Ltd, 2 nd Edition, New Delhi, 2011. 2. Burden.R.L. andFaires.T.D., “Numerical Analysis”, Thomson Asia Pvt. Ltd., 7th Edition, Singapore, 2002. Page 16 of 85
  17. 17. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2402 DC MACHINES AND TRANSFORMERS 3 1 0 4 AIM To introduce the basic concepts of rotating machines and to expose the students to the concepts of DC machines and Transformers and analyse their performance. OBJECTIVES To impart knowledge on · Principles of electromechanical energy conversion and basic concepts in rotating machines. · Construction, principle of operation and performance of DC generators. · Principle of operation, performance, starting methods and speed control of DC motors. · Construction, principle of operation and performance of transformers. · Losses and efficiency, testing of DC machines and transformers. UNIT - I BASIC CONCEPTS OF ROTATING MACHINES 8 Principles of electromechanical energy conversion – Single and multiple excited systems – Field energy and co-energy – Force and Torque - MMF of distributed A.C. windings – Rotating magnetic field – Generated voltage – Torque in round rotor machine. UNIT - II DC GENERATORS 9 Constructional details – Principle of operation - EMF equation – Methods of excitation – Self and separately excited generators – Characteristics of series, shunt and compound generators – Armature reaction and commutation – Parallel operation of DC shunt and compound generators. UNIT - III DC MOTORS 9 Principle of operation – Back EMF and torque equations – Characteristics of series, shunt and compound motors – Starting of DC motors – Types of starters – Speed control of DC series and shunt motors. UNIT - IV TRANSFORMERS 10 Constructional details - principle of operation – types - EMF equation – Transformation ratio – Transformer on no-load – Transformer on load - Equivalent circuit - Regulation - Parallel operation of transformers - Three phase transformer connections - Auto transformer. UNIT - V TESTING OF DC MACHINES AND TRANSFORMERS 9 Losses and efficiency in DC machines and transformers – Condition for maximum efficiency Testing of DC machines – Brake test, Swinburne’s test, Hopkinson’s test and Retardation test – Testing of transformers – Polarity test - Open circuit and short circuit tests – Sumpner’s test – All day efficiency. Note: UNIT 5 may be covered along with UNIT 2, 3, and 4. Total periods (45+15T): 60 TEXT BOOKS 1. Kothari D.P., & Nagrath I.J., “Electric Machines”, Tata McGraw Hill Publishing Company Ltd, 3rd Edition, 2004. 2. Albert E. Clayton and Hancock N. N., “The performance and Design of Direct Current Machines”, Oxford and IBH Publishing Company Pvt. Ltd., New Delhi, 1990. REFERENCES 1. Gupta J.B., “Theory and Performance of Electrical Machines”, S.K.Kataria and Sons,14th Edition, 2009. 2. Fitzgerald.A.E., Charles Kingsely Jr, Stephen D.Umans, “Electric Machinery”, McGraw Hill Books Company, 6th Edition, 2003. 3. Irving L. Kosow “Electric Machinery and Transformers” PHI, New Delhi, 2nd Edition, 1991. Page 17 of 85
  18. 18. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2403 TRANSMISSION AND DISTRIBUTION OF ELECTRICAL ENERGY 3 0 0 3 AIM To become familiar with the function of different components used in Transmission and Distribution levels of power systems and modeling of these components. OBJECTIVES · To develop expression for computation of fundamental parameters of lines. · To categorize the lines into different classes and develop equivalent circuits for these classes. · To analyse the voltage distribution in insulator strings and cables and methods to improve the same. UNIT - I INTRODUCTION 9 Structure of electric power system: Various levels such as generation, transmission and distribution; HVDC and EHV AC transmission: comparison of economics of transmission, technical performance and reliability, application of HVDC transmission system. FACTS (qualitative treatment only): TCSC, SVC, STATCOM, UPFC. UNIT - II TRANSMISSION LINE PARAMETERS 9 Parameters of single and three phase transmission lines with single and double circuits: Resistance, inductance and capacitance of solid, stranded and bundled conductors: Symmetrical and unsymmetrical spacing and transposition; application of self and mutual GMD; skin and proximity effects; interference with neighbouring communication circuits. Typical configuration, conduct types and electrical parameters of 400, 220, 110, 66 and 33 kV lines. UNIT - III MODELLING AND PERFORMANCE OF TRANSMISSION LINES 9 Classification of lines: Short line, medium line and long line; equivalent circuits, attenuation constant, phase constant, surge impedance; transmission efficiency and voltage regulation; real and reactive power flow in lines: Power-angle diagram; surge-impedance loading, load ability limits based on thermal loading, angle and voltage stability considerations; shunt and series compensation, Ferranti effect and corona loss. UNIT - IV INSULATORS AND CABLES 9 Insulators: Types, voltage distribution in insulator string and grading, improvement of string efficiency. Underground cables: Constructional features of LT and HT cables, capacitance, dielectric stress and grading, thermal characteristics. UNIT - V SUBSTATION, GROUNDING SYSTEM AND DISTRIBUTION SYSTEM 9 Types of substations; bus-bar arrangements; substation bus schemes: single bus scheme, double bus with double breaker, double bus with single breaker, main and transfer bus, ring bus, breaker-and-a-half with two main buses, double bus-bar with bypass isolators. Resistance of grounding systems: Resistance of driven rods, resistance of grounding point electrode, grounding grids; design principles of substation grounding system; neutral grounding. Radial and ring-main distributors; interconnectors; AC distribution: AC distributor with concentrated load; three-phase, four-wire distribution system; sub-mains; stepped and tapered mains. Total periods: 45 TEXT BOOKS 1. Gupta B.R, “Power System Analysis and Design”, S.Chand and company, New Delhi, 2008. 2. Singh S.N, “Electric Power Generation, Transmission and Distribution”, Prentice Hall of India Pvt. Ltd, New Delhi, 2004. REFERENCES 1. Luces M.Fualkenberry, Walter Coffer, “Electrical Power Distribution and Transmission”, Pearson education, 2007. 2. Begamudre R.D, “Extra high voltage AC Transmission Engineering”, NewAge International (P) Ltd., January 2009. 3. Central Electricity Authority (CEA), “Guidelines for Transmission System Planning”, New Delhi 4. Tamil Nadu Electricity Board Handbook, 2003. Page 18 of 85
  19. 19. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2404 IC FABRICATION AND LINEAR INTEGRATED CIRCUITS 3 0 0 3 AIM To expose the students to the concepts of IC fabrication, characteristics of op-amp, applications of op-amp and special ICs. OBJECTIVES · To study the IC fabrication. · To study characteristics of Op-amp, sine wave oscillators and waveform generators using Op-amp ICs. · To study the applications of Op-amp. · To study internal functional blocks and applications of special ICs like 555 IC Timer, 565 IC PLL, 723 & LM317 IC Regulators, and AD533 IC Analog multiplier. · To study the various types of ADCs and DACs. UNIT - I IC FABRICATION 9 IC classification, fundamental of monolithic IC technology- Epitaxial growth- Masking and etching- Diffusion of impurities- Isolation Techniques- Metallization- Packaging- Fabrication of Transistors, Diodes, Capacitors and Resistors- Fabrication of a typical circuit. UNIT - II CHARACTERISTICS OF OPAMP 9 Ideal OP-AMP characteristics- DC characteristics- Voltage series feedback and shunt feedback amplifiers- Differential amplifier- AC characteristics- Frequency response of OP-AMP- Basic applications of op-amp– Summer, differentiator and integrator. UNIT - III APPLICATIONS OF OPAMP-I 9 Instrumentation amplifier- First and second order active filters- V/I & I/V converters- Comparators- Sine wave oscillators- Square, triangular and sawtooth wave generators- Peak detector- Clipping and Clamping circuits. UNIT - IV APPLICATIONS OF OPAMP-II 9 S/H circuit- D/A converter- R-2R ladder and weighted resistor types- A/D converter - Dual slope, successive approximation and flash types. UNIT -V SPECIAL IC”S AND THEIR APPLICATIONS 9 555 Timer IC – Functional block diagram & applications; 565 IC-Phase lock loop- Functional block diagram and applications, LM317 and 723 IC voltage regulators, MA 7840 IC switching regulator- MCT2E IC opto-coupler- -AD533 IC Analog multiplier. Total periods: 45 TEXT BOOKS 1. Ramakant A.Gayakward, “Op-amps and Linear Integrated Circuits”, 4th Edition, Pearson Education, New Delhi, 2011. 2. Roy Choudhary D, Sheil B.Jani, “Linear Integrated Circuits”, 4th Edition, New Age International Publishers, 2010 REFERENCES 1. Jacob Millman, Christos C. Halkias, “Integrated Electronics: Analog and Digital circuitssystem”, 2nd Edition, Tata McGraw Hill, 2011. 2. Robert F. Coughlin, Fredrick F. Driscoll, “Op-amps and Linear ICs”, Pearson Education, 6th Edition, 2011. 3. David A. Bell, “Op-amp & Linear ICs”, Prentice Hall of India, 2nd Edition, 1997. 4. Salivahanan S, V.S. Kanchana Bhaaskaran, “Linear Integrated Circuits”, New Delhi, Tata McGraw-Hill, 2008. Page 19 of 85
  20. 20. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2405 INTRODUCTION TO SIGNALS AND SYSTEMS 3 1 0 3 AIM To study and analyze the characteristics of continuous and discrete signals and systems. OBJECTIVES · To study the properties and representation of discrete and continuous signals. · To study the sampling process and analysis of discrete system using Z-transform. · To analyse continuous time system using Fourier and Laplace transforms. · To learn about analysis and synthesis of discrete time systems. · To learn about system with impulse response. UNIT - I REPRESENTATION OF SIGNALS 9 Continuous and discrete time signals: Classification of Signals – Periodic and aperiodic – Even and odd – Energy and power signals – Deterministic and random signals–periodicity – Properties of discrete time complex exponential UNIT impulse – UNIT step impulse functions –Transformation in independent variable of signals: time scaling, time shifting. Determination of Fourier series - Representation of continuous time and discrete time periodic signals. UNIT - II ANALYSIS OF CONTINUOUS TIME SIGNALS AND SYSTEMS 9 Continuous time Fourier Transform and Laplace Transform analysis with examples – Properties of the Continuous time Fourier Transform and Laplace Transform basic properties, Parseval’s relation, and convolution in time and frequency domains. Basic properties of continuous time systems: Linearity, Causality, time invariance, stability, magnitude and Phase representations of frequency response of LTI systems -Analysis and characterization of LTI systems using Laplace transform: Computation of impulse response and transfer function using Laplace transform. UNIT - III SAMPLING THEOREM AND Z-TRANSFORM 9 Representation of continuous time signals by its sample - Sampling theorem – Reconstruction of a Signal from its samples, aliasing – Discrete time processing of continuous time signals, sampling of band pass signals - Basic principles of z-transform - Z-transform definition – Region of convergence – Properties of ROC – Properties of z-transform – Poles and Zeros – Inverse z-transform using Contour integration – Residue Theorem, Power Series expansion and Partial fraction expansion, Relationship between z-transform and Fourier transform. UNIT - IV DISCRETE TIME SYSTEMS 9 Computation of Impulse response & Transfer function using Z Transform. DTFT Properties and examples – LTI-DT systems -Characterization using difference equation – Block diagram representation – Properties of convolution and the interconnection of LTI Systems-Static variable equations and matrix representation of system. UNIT - V SYSTEMS WITH FINITE AND INFINITE DURATION IMPULSE RESPONSE 9 Systems with finite duration and infinite duration impulse response – recursive and non-recursive discrete time system – realization structures – direct form – I, direct form – II, cascade and parallel forms. Total periods (45+15T): 60 TEXT BOOKS 1. AlanV.Oppenheim, Alan S.Willsky with Hamid Nawab.S, “Signals & Systems”, 3/e, Pearson Education, 2000. REFERENCES 1. John G.Proakis and Dimitris G.Manolakis, “Digital Signal Processing, Principles, Algorithms and Applications”, 4/e PHI, 2007. 2. M.J.Roberts, “Fundamentals of Signals and Systems”, TMH 2008. 3. K.Lindner, “Signals and Systems”, McGraw Hill International, 2000. 4. H.P.Hsu, “Signals and systems “, Schaum”s outlines, Tata McGraw-Hill Co Ltd., 2006. Page 20 of 85
  21. 21. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2406 PRINCIPLES OF COMMUNICATION ENGINEERING 3 0 0 3 AIM To introduce the concepts of communication systems engineering using wire and wireless medium OBJECTIVES · To introduce different methods of analog communication and their significance. · To introduce Digital Communication methods for high bit rate transmission.. · To introduce the concepts of source and line coding techniques for enhancing rating of transmission of minimizing the errors in transmission. · To introduce MAC used in communication systems for enhancing the number of users. · To introduce various media for digital communication UNIT - I ANALOG COMMUNICATION 9 AM – Frequency spectrum – Vector representation – Power relations – Generation of AM – DSB,DSB/SC, SSB, VSB AM Transmitter & Receiver; FM and PM – Frequency spectrum – Power relations : NBFM & WBFM, Generation of FM and DM, Amstrong method & Reactance modulations :FM & PM frequency. UNIT - II DIGITAL COMMUNICATION 9 Pulse modulations – Concepts of sampling and sampling theormes, PAM, PWM, PPM, PTM,quantization and coding : DCM, DM, slope overload error. ADM, DPCM, OOK systems –ASK, FSK, PSK, BSK, QPSK, QAM, MSK, GMSK, applications of Data communication. UNIT - III SOURCE CODES, LINE CODES & ERROR CONTROL (Qualitative only) 9 Primary communication – Entropy, properties, BSC, BEC, source coding : Shaum, Fao, Huffman coding : noiseless coding theorum, BW – SNR trade off codes: NRZ, RZ, AMI, HDBP, ABQ,MBnB codes : Efficiency of transmissions, error control codes and applications:convolutions & block codes. UNIT - IV MULTIPLE ACCESS TECHNIQUES 9 SS&MA techniques: FDMA, TDMA, CDMA, SDMA application in wire and wireless communication: Advantages (merits), Wi-Fi, i-pad, i-pod, Blue tooth devices. UNIT - V SATELLITE, OPTICAL FIBER – POWERLINE, SCADA 9 Orbits: types of satellites: frequency used link establishment, MA techniques used in satellite Communication, earth station; aperture actuators used in satellite – Intelsat and Insat: fibers – Types: sources, detectors used, digital filters, optical link: power line carrier communications: SCADA Total periods: 45 TEXT BOOKS 1.Taub & Schiling “Principles of communication systems” Tata McGraw hill 2007 2.Das J, Chatterjee P.K., Mullik S.K., “Principles of digital communication” New Age International, 2nd Edition, 2012. REFERENCES 1. Kennedy and Davis “Electronic communication systems” Tata McGraw hill, 4th edition, 1993, 35th Reprint (2008). 2. Sklar “Digital communication fundamentals and applications“ Pearson Education, 2nd Edition, 2001 3. Bary le, Memuschmidt, digital Communication, Kluwer Publication, 2004. 4. Lathi B.P, “Modern digital and analog communication systems” Oxford University Press, 4th Edition, 2009. Page 21 of 85
  22. 22. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2407 DC MACHINES AND TRANSFORMERS LABORATORY 0 0 3 2 AIM To expose the students to the operation of D.C. machines and transformers and give them experimental skill. EXPERIMENTS 1. Open circuit and load characteristics of D.C separately and self excited shunt generator 2. Load characteristics of D.C. compound generator with differential and cumulative connections 3. Load characteristics of D.C. shunt motor 4. Load characteristics of D.C. compound motor 5. Load characteristics of D.C series motor 6. Swinburne”s test 7. Speed control of D.C shunt motor 8. Hopkinson”s test on D.C motor – generator set 9. Load test on single-phase transformer and 10. Open circuit and short circuit tests on single phase transformer 11. Sumpner”s test on transformers 12. Separation of no-load losses in single phase transformer Practical 45 Additional experiments 13. Study of D.C.motor starters 14. Three phase transformer connections Page 22 of 85
  23. 23. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2408 LINEAR INTEGRATED CIRCUITS LABORATORY 0 0 3 2 AIM To impart practical knowledge to the students to understand the basic concepts and applications of op-amps and special ICs. OUTCOMES After successful completion of this course, the students will be able to, · Design op-amp circuits for practical applications. · Design voltage regulators, A/D and D/A converters for practical applications. · Design Astable and Monostable multivibrators using 555 Timer IC for practical applications. · Design frequency multiplier using 565 PLL IC for practical applications. LIST OF EXPERIMENTS 1. Inverting and non-inverting amplifiers 2. Integrator and differentiator 3. Square and Triangular wave generators 4. Op-Applications – Adder, Subtractor, Averaging amplifier 5. Comparators using LM311 IC 6. 555 Timer IC Applications- Astable and Monostable multivibrator 7. Analog to Digital and Digital to Analog Converters. 8. 565 PLL IC Applications - Frequency multiplier 9. 723 IC and LM317 IC Voltage Regulators 10. Differential and Instrumentation amplifier 11. Measurement of op-amp parameters Practical 45 Page 23 of 85
  24. 24. For the students admitted from the Academic year 2012-2013(R 2012) V SEMESTER 12EE2501 CONTROL SYSTEM ENGINEERING 3 1 0 4 AIM To expose the students to the basic concepts of control systems. OBJECTIVES · To understand the open loop and closed loop systems. · To understand the modelling of physical systems using transfer function and state space approach. · To understand time domain and frequency domain analysis of control systems. · To understand the compensation techniques used to stabilize control systems. UNIT - I CONTROL SYSTEM MODELLING 9 System concept- Open loop and closed loop systems- Modelling of electrical, mechanical, and electromechanical systems- Transfer function of DC generator- DC and AC servomotor- Electrical analogy of mechanical systems- Block diagram representation of systems- Block diagram reduction Techniques- Signal flow graphs- Mason”s gain formula- Examples. UNIT - II TIME DOMAIN ANALYSIS 9 Standard Test signals–Time response of first and second order systems- Performance parameters- Type and order of systems- Steady state error constants - Generalized error series– Steady state error- Introduction to P, PI and PID controllers- Design of PID controllers. UNIT - III FREQUENCY DOMAIN ANALYSIS 9 Frequency domain specifications – Peak resonance- Resonant frequency- Bandwidth and cut-off rate- Correlation between time and frequency response of second order systems- Bode plots- Polar plots- Determination of closed loop response from open loop response. UNIT - IV STABILITY ANALYSIS 9 Characteristic equation – Location of roots of characteristic equation for stability– Absolute stability and Relative stability- Routh Hurwitz criterion for stability- Root locus– Effect of pole- Zero addition, Nyquist stability criterion- Gain margin- phase margin. UNIT – V COMPENSATOR AND STATE SPACE REPRESENTATION 9 Design of lag, lead, and lag-lead compensator using Bode plot - Modelling of physical systems using state space approach- Advantages of state space approach over transfer function model. Total periods (45+15T): 60 TEXT BOOKS 1. Nagrath I.J and Gopal M, “Control Systems Engineering”, New Age International Publishers, 5th edition, 2008. REFERENCESS 1. Benjamin C. Kuo, “Automatic Control Systems”, John Wiley and Sons, 9th Edition, 2010. 2. Gopal M, “Control Systems, Principles & Design”, Tata McGraw Hill, New Delhi, 3rd Ed., 2008. 3. Bandyopadhyay M.N,“Control Engineering Theory and Practice”, Prentice Hall of India, 2003 4. Ogata K, “Modern Control Engineering”, 5th edition, Pearson Education, New Delhi, 2010. 5. Norman S. Nise, Control Systems Engineering, 5th Edition, John Wiley, New Delhi, 2009. 6. Samarjit Ghosh, Control systems, Pearson Education, New Delhi, 2004. Page 24 of 85
  25. 25. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2502 SYNCHRONOUS AND INDUCTION MACHINES 3 1 0 4 AIM To expose the students to the concepts of synchronous and asynchronous machines and to analyse their performance. OBJECTIVES To impart knowledge on · Construction and performance of salient and non – salient type synchronous generators. · Principle of operation and performance of synchronous motor. · Construction, principle of operation and performance of induction machines. · Starting and speed control of three-phase induction motors. · Construction, principle of operation and performance of single phase induction motors and special machines. UNIT - I SYNCHRONOUS GENERATOR 9 Constructional details – Types of rotors – emf equation – Synchronous reactance – Armature reaction – Voltage regulation – e.m.f, m.m.f, z.p.f and A.S.A methods – Synchronizing and parallel operation – Synchronizing torque - Change of excitation and mechanical input – Two reaction theory – Determination of direct and quadrature axis synchronous reactance using slip test – Operating characteristics - Capability curves. UNIT - II SYNCHRONOUS MOTOR 8 Principle of operation – Torque equation – Operation on infinite bus bars - Phasor diagrams -V and inverted V curves - Hunting – Power input and power developed equations – Starting methods – Current loci for constant power input, constant excitation and constant power developed. UNIT - III THREE PHASE INDUCTION MOTOR 12 Constructional details – Types of rotors – Principle of operation – Slip – Equivalent circuit – Slip-torque characteristics - Condition for maximum torque – Losses and efficiency – Load test - No load and blocked rotor tests - Circle diagram – Separation of no load losses – Double cage rotors – Induction generator – Synchronous induction motor. UNIT - IV STARTING AND SPEED CONTROL OF THREE PHASE INDUCTION MOTOR 7 Need for starting – Types of starters – Stator resistance and reactance, autotransformer and star-delta starters – Rotor resistance starter – Speed control – Change of voltage, frequency, number of poles and slip – Cascaded connection – Slip power recovery scheme. UNIT - V SINGLE PHASE INDUCTION MOTORS AND SPECIAL MACHINES 9 Constructional details of single phase induction motor – Double revolving field theory and operation – Equivalent circuit – No load and blocked rotor test – Performance analysis – Starting methods of single-phase induction motors - Special machines - Shaded pole induction motor, reluctance motor, repulsion motor, hysteresis motor, stepper motor and AC series motor. Total periods (45+15T): 60 TEXT BOOKS 1. Kothari D.P and Nagrath I.J., “Electric Machines”, Tata McGraw Hill Publishing Company Ltd, 4th Edition, 2010. REFERENCES 1. Gupta J.B, “Theory and Performance of Electrical Machines”, S.K.Kataria and Sons, 2002. 2. Murugesh Kumar K, “Induction and synchronous machines” Vikas publishing house Pvt Ltd., 2009. 3. Sheila.C.Haran, “Electrical Machines II”, Scitech Publications, 2nd Edition 2008. 4. Say M.G, “Alternating Current Machines”, 5th Edition, Pitman, 1992. 5. Bhimbhra P.S, “Electrical Machinery”, Khanna Publishers, 2003. Page 25 of 85
  26. 26. For the students admitted from the Academic year 2012-2013(R 2012) Page 26 of 85
  27. 27. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2503 POWER SYSTEM PROTECTION AND SWITCHGEAR 3 0 0 3 AIM To study the various faults and protection schemes in power systems. OBJECTIVES · To discuss the need for the protection and various protection schemes. · To study relays characteristics · To study apparatus protection · To understand the method of circuit breaking, arcing phenomena – various arc theories-capacitive and inductive breaking · To understand the working of different types of circuit breakers and their testing methods UNIT- I INTRODUCTION 9 Principles and need for protective schemes – nature and causes of faults – types of faults – fault current calculation using symmetrical components – Earthing – Zones of protection and essential qualities of protection – Protection schemes – CTs and PTs and their applications. UNIT - II PROTECTIVE RELAYS 9 Operating principles of relays, the universal relay, electromagnetic relays (including torque equation, relay characteristics): over current, directional, distance and differential relays, negative sequence relays, frequency relays - static relays (including amplitude and phase comparators), Introduction to numerical relays. UNIT - III APPARATUS PROTECTION 9 Apparatus protection – transformer, generator, motor - protection of bus bars, transmission lines UNIT - IV THEORY OF CIRCUIT INTERRUPTION 9 Physics of arc phenomena and arc interruption, Restriking voltage & Recovery voltage, rate of rise of recovery voltage, resistance switching, current chopping, Interruption of capacitive current – DC circuit breaking. UNIT - V CIRCUIT BREAKERS 9 Types of Circuit Breakers – Oil and Air blast circuit breakers (Qualitative Treatment only), SF6 and Vacuum circuit breakers - Air break circuit breakers – comparative merits of different circuit breakers – Testing of circuit breakers. Total periods: 45 TEXT BOOKS 1. Badri Ram, Vishwakarma, “Power System Protection and Switchgear”, Tata McGraw Hill Publishing Co. Ltd., 2001. 2. Bhuvanesh Oza,Nirmal-Kumar Nair, Rashesh Mehta,Vijay Makwana, “Power System Protection & Switchgear”, First Edition, Tata McGraw hill, 2010. REFERENCE BOOKS 1. Sunil S. Rao, “Switchgear and Protection”, Khanna publishers, New Delhi, 1986. 2. Wadhwa C.L., “Electrical Power Systems”, New age International (P) Ltd., Fourth Edition, 2005. Page 27 of 85
  28. 28. For the students admitted from the Academic year 2012-2013(R 2012) 3. Paithankar Y.G., and Bhide S.R., “Fundamentals of Power System Protection”, Prentice Hall of India Pvt. Ltd., New Delhi – 110001, 2003. 4. Van A. R. and Warrington C., “Protective Relays - Their Theory and Practice: Vol. I and Vol. II”, Third Edition, Chapman and Hall Ltd. 5. Madhavrao T.S., “Power System Protection: Static Relays”, Tata McGraw Hill Publishing Co. Ltd., Second Edition, 2008. 6. Lythall R.T., “J and P Switchgear Handbook”, Newness Butterworths, 1972. 7. Prof. S.A. Soman, IIT, Bombay, Web course on “Power System Protection”, http://www.nptel.iiim.ac.in 8. Madhavrao T.S., “Digital Numerical Relays”, Tata McGraw Hill Publishing Co. Ltd., 2005. Page 28 of 85
  29. 29. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2504 MICROPROCESSORS AND MICRO CONTROLLERS 3 0 0 3 AIM To introduce Microprocessor Intel 8085, Arm processor and Micro Controllers OBJECTIVES · To study about architecture and programming of 8085. · To learn about Pentium processor. · To study about arm processor. · To study about 8051 microcontroller. · To learn about PIC microcontroller. UNIT - I 8085 PROCESSOR & PROGRAMMING 9 Functional block diagram – Memory interfacing - Interrupt structure.- Instruction set and addressing modes- Assembly language format-simple programming exercises. UNIT - II PENTIUM PROCESSOR 9 Intel Pentium processors-Superscalar architecture and signals-special registers-cache structure-memory management-Instruction set-Simple programs. UNIT - III ARM PROCESSOR 9 The ARM architecture-ARM Assembly Language Program-ARM organization-Instruction set-The thumb Instruction set-ARM CPU cores. UNIT - IV MICRO CONTROLLER 8051 9 Functional block diagram - Instruction set and addressing modes – Interrupt structure-simple programming exercises- Use of C compliers for 8051. UNIT - V PIC MICROCONTROLLER 9 CPU Architecture-Instruction set-Interrupts-I2C bus-Timers-I/O port expansion-UART. Total periods: 45 TEXT BOOKS 1. Gaonkar, S., “Microprocessor Architecture Programming and Application”, Penram International, Fifth Edition, New Delhi, 2002. 2. Muhammad Ali Mazidi & Janice Gilli Mazidi, “The 8051 Micro Controller and Embedded Systems”, Pearson Education, 5th Indian reprint, 2003. 3. Barry. B. Bery “The Intel Microprocessors 8086/8088,80186/80188,80286,80386,80486,pentium and Pentium pro processor-Architecture, programming and Interfacing”, Prentice Hall of India pvt.Ltd., Seventh Edition, 2006. REFERENCES 1. Steve Furber, “ARM Sytem –On Chip architecture”, Addison Wesley, 2000. 2. John.B.Peatman, “Design with PIC Microcontrollers” Pearson Education, 1998. Page 29 of 85
  30. 30. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2505 DIGITAL SIGNAL PROCESSING FOR ELECTRICAL ENGINEERS 3 1 0 3 AIM To study the signal processing methods, processors and applications. OBJECTIVES · To study DFT and its computation · To study the design techniques for digital filters · To study the finite word length effects in signal processing · To study the fundamentals of digital signal processors. · To study the DSP applications UNIT - I FAST FOURIER TRANSFORM 9 Introduction to DFT – Efficient computation of DFT- Properties of DFT – FFT algorithms – Radix-2 FFT algorithms – Decimation in Time – Decimation in Frequency algorithms – convolution- overlap save method. UNIT - II DESIGN OF INFINITE IMPULSE RESPONSE DIGITAL FILTER 9 Review of design of analogue Butterworth and Chebyshev Filters- Frequency transformation in analog domain – Design of IIR digital filters using impulse invariance technique – Design of IIR digital filters using bilinear transformation – pre warping – Frequency transformation in digital domain – Realization - Direct form I, Direct form II, cascade and parallel. UNIT - III DESIGN OF FINITE IMPULSE RESPONSE DIGITAL FILTERS 9 Linear phase response of FIR- Windowing techniques for design of linear phase FIR filters: Rectangular- Hamming- Hanning- Blackman and Kaiser Windows. Gibbs phenomenon – Frequency sampling technique-. Realization of FIR filters-lattice structure- Comparision of FIR & IIR. UNIT - IV FINITE WORD LENGTH EFFECTS & DIGITAL SIGNAL PROCESSOR 9 Quantization noise – derivation for quantization noise power – Binary fixed point and floating-point number representations – Comparison – truncation and rounding error – input quantization error-coefficient quantization error – limit cycle oscillations-dead band- overflow error-signal scaling-scaling-Introduction to general and special purpose hardware for DSP – Harvard architecture-Pipelining – Addressing Modes – Overview of Architecture and instruction set of TMS320C50. UNIT – V APPLICATIONS OF DIGITAL SIGNAL PROCESSING 9 Speech and Audio Signal Processing- Radar Signal Processing- Vocal Mechanism-Speech Technology- Parameters of Speech- Speech Analysis- Speech Loading- Digital Processing of Audio Signals- Biomedical-ECG, EEG. Total periods (45+15T): 60 TEXT BOOKS 1. John G Proakis- Dimtris G Manolakis- Digital Signal Processing Principles- Algorithms and Application- Pearson/PHI- 4th /e- 2007. 2. Allan V.Openheim, Ronald W.Sehafer & John R.Buck-“Discrete Time Signal Processing”, second /e- Pearson/Prentice Hall. 3. Mitra S.K, “Digital Signal Processing- A Computer based approach”- Tata McGraw-Hill- 1998- New Delhi. REFERENCES 1. Venkataramani B & Bhaskar M, “Digital Signal Processor Architecture- Programming and application” TMH 2002. 2. Johny R ”Johnson Introduction to Digital Signal Processing” Prentice Hall- 1984. 3. Li Tan, “Digital Signal Processing” Elsevier-2008. Page 30 of 85
  31. 31. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2506 DATA STRUCTURES AND DEVELOPING ALGORITHMS 3 0 0 3 AIM To provide an in-depth knowledge in problem solving techniques and data structures. OBJECTIVES · To learn the systematic way of solving problems · To understand the different methods of organizing large amounts of data · To learn to program in C · To efficiently implement the different data structures · To efficiently implement solutions for specific problems UNIT - I INTRODUCTION TO DATA STRUCTURES 9 Abstract data types - Sequences as value definitions - Data types in C - Pointers in C -Data structures and C - Arrays in C - Array as ADT - One dimensional array -Implementing one dimensional array - Array as parameters - Two dimensional array -Structures in C - Implementing structures - Unions in C - Implementation of unions -Structure parameters - Allocation of storage and scope of variables. Recursive definition and processes: Factorial function - Fibonacci sequence - Recursion in C - Efficiency of recursion. UNIT - II STACK, QUEUE AND LINKED LIST 9 Stack definition and examples – Primitive operations – Example - Representing stacks in C - Push and pop operation implementation. Queue as ADT - C Implementation of queues - Insert operation - Priority queue - Array implementation of priority queue. Inserting and removing nodes from a list-linked implementation of stack, queue and priority queue - Other list structures - Circular lists: Stack and queue as circular list -Primitive operations on circular lists. Header nodes - Doubly linked lists - Addition of long positive integers on circular and doubly linked list. UNIT - III TREES 9 Binary trees: Operations on binary trees - Applications of binary trees - Binary tree representation - Node representation of binary trees - Implicit array representation of binary tree – Binary tree traversal in C - Threaded binary tree - Representing list as binary tree - Finding the Kth element - Deleting an element. Trees and their applications: C representation of trees - Tree traversals - Evaluating an expression tree - Constructing a tree. UNIT -IV SORTING AND SEARCHING 9 General background of sorting: Efficiency considerations, Notations, Efficiency of sorting. Exchange sorts; Bubble sort; Quick sort; Selection sort; Binary tree sort; Heap sort. Heap as a priority queue - Sorting using a heap-heap sort procedure - Insertion sorts: Simple insertion - Shell sort - Address calculation sort - Merge sort -Radix sort.Sequential search: Indexed sequential search - Binary search - Interpolation search. UNIT - V GRAPHS 9 Application of graph - C representation of graphs - Transitive closure - Warshall”s algorithm – Shortest path algorithm - Linked representation of graphs - Dijkstra”s algorithm - Graph traversal - Traversal methods for graphs - Spanning forests - Undirected graph and their traversals - Depth first traversal - Application of depth first traversal - Efficiency of depth first traversal - Breadth first traversal - Minimum spanning tree - Kruskal”s algorithm - Round robin algorithm. Total periods: 45 TEXT BOOKS 1. Aaron M. Tenenbaum, Yeedidyah Langsam, Moshe J. Augenstein, “Data structures using C”, Pearson Education, 2004 / PHI REFERENCES 1. Balagurusamy E, “Programming in Ansi C”, Fifth Edition, Tata McGraw Hill Publication, 2010. 2. Robert L. Kruse, Bruce P. Leung Clovis L.Tondo, “Data Structures and Program Design in C”, Pearson Education, 2000 / PHI. Page 31 of 85
  32. 32. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2507 SYNCHRONOUS AND INDUCTION MACHINES LABORATORY 0 0 3 2 AIM To expose the students to the operation of synchronous machines and induction motors and give them experimental skill. EXPERIMENTS 1. Regulation of three phase alternator by emf and mmf methods. 2. Regulation of three phase alternator by ZPF and ASA methods. 3. Regulation of three phase salient pole alternator by slip test. 4. Measurements of negative sequence and zero sequence impedance of alternators. 5. V and Inverted V curves of three Phase Synchronous Motor. 6. Load test on three-phase induction motor. 7. No load and blocked rotor test on three-phase induction motor. 8. Separation of No-load losses of three-phase induction motor. 9. Load test on single-phase induction motor 10. No load and blocked rotor test on single-phase induction motor. Practical 45 Additional experiments 11. Study of starters for synchronous and induction motors. 12. Parallel operation of three phase alternators. Page 32 of 85
  33. 33. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2508 DATA STRUCTURES AND ALGORITHMS LABORATORY 0 0 3 2 AIM To train the students in developing algorithms and writing programs in data structures. EXPERIMENTS 1. Queue implementation using arrays. 2. Stack implementation-using arrays. 3. Singly, doubly and circular liked list implementation and all possible operation on lists. 4. Queue and Stack implementation using linked list 5. Binary search tree implementation using linked list and possible operations on binary search trees 6. In-order, pre-order and post order traversals. 7. Quick sort implementation and its efficiency calculation. 8. Binary Search implementation. 9. Graph implementation-using arrays and list structure. 10. Depth first and Breadth first traversal in graphs. Practical 45 Page 33 of 85
  34. 34. For the students admitted from the Academic year 2012-2013(R 2012) 12EN2001 COMMUNICATION SKILLS LABORATORY 0 0 2 1 AIM Globalization has brought in numerous opportunities for the teeming millions, with more focus on the students over all capability apart from academic competence. Many students, particularly those from non- English medium schools, find that they are not preferred due to their inadequacy of communication skills and soft skills, despite possessing sound knowledge in their subject area along with technical capability. Keeping in view their pre-employment needs and career requirements, this course on Communication Skills Laboratory will prepare students to adapt themselves with ease to the industry environment, thus rendering them as prospective assets to industries. The course will equip the students with the necessary communication skills that would go a long way in helping them in their profession. OBJECTIVES · To equip students of engineering and technology with effective speaking and listening skills in English. · To help them develop their soft skills and people skills, which will make The transition from college to workplace smoother and help them to excel in their jobs. · To enhance students’ performance at Placement Interviews, Group Discussions and other recruitment exercises. I.PC based session (weightage- 40%) A. English Language Lab 1. Listening Comprehension Listening and typing- Listening and sequencing of sentences - Filling in the blanks - Listening and answering the questions. 2. Reading Comprehension and Vocabulary Filling in the blanks - Cloze Exercises - vocabulary building –Verbal Passages. 3. Speaking. Phonetics: Intonation - Ear Training - Correct Pronunciation - Sound recognition exercises - Common Errors in English. Conversations: Face to Face Conversation - Telephone Conversation -Role play activities (Students take on roles and engage in Conversation) B. Career Lab (Samples are available to learn and practice in the class room session) 1. Resume / Report preparation / Letter writing Structuring the resume / report - Letter writing / E-mail Communication -Samples. 2. Presentation skills Elements of an effective presentation - Structure of a presentation - Presentation tools - Voice Modulation- Audience analysis - Body Language -Video Samples 3. Group Discussion Page 34 of 85
  35. 35. For the students admitted from the Academic year 2012-2013(R 2012) Why is GD part of selection process? - Structure of a GD - Moderator- Led and other GDs - Strategies in GD - Team work - Body Language - Mock GD -Video samples 4. Interview Skills Kinds of Interviews -Required Key Skills - Corporate culture - Mock Interviews -Video Samples 5. Corporate Etiquette: Telephone etiquette-email etiquette-dining etiquette II Class Room Session (Weightage - 60 %) Periods · Presentation Skills. · Group Discussion. · Presenting a Sales Plan. · Presenting a Company Profile · Product Demonstration. · Mock Interview. · Introducing a famous personality to the Audience. · Welcome address & Vote of thanks. · Case Study.(Related to Engineering). · Decision Making & Problem Solving Techniques. Note: Class room sessions are practice sessio Page 35 of 85
  36. 36. For the students admitted from the Academic year 2012-2013(R 2012) VI SEMESTER 12EE2601 ELECTRIC MACHINE DESIGN 3 1 0 4 AIM To expose the students to the concept of design of various types of electrical machines OBJECTIVES To provide sound knowledge about constructional details and design of various electrical machines. · To study mmf calculation and thermal rating of various types of electrical machines. · To design armature and field systems for D.C. machines. · To design core, yoke, windings and cooling systems of transformers. · To design stator and rotor of induction machines. · To design stator and rotor of synchronous machines and study their thermal behaviour. UNIT - I INTRODUCTION 9 Major considerations in Electrical Machine Design - Electrical Engineering Materials – Space factor –Choice of Specific Electrical and Magnetic loadings - Thermal considerations - Heat flow –Temperature rise - Rating of machines – Standard specifications. UNIT - II D.C. MACHINES 9 Output equation – Main dimensions - Choice of specific loadings – Choice of number of poles – Armature design – Design of field poles and field coil – Design of commutator and brushes – Losses and efficiency calculations. UNIT - III TRANSFORMERS 9 Output rating of single phase and three phase transformers – Optimum design of transformers – Design of core, yoke and windings for core and shell type transformers – Equivalent circuit parameter from designed data – Losses and efficiency calculations – Design of tank and cooling tubes of transformers. UNIT IV THREE PHASE INDUCTION MOTORS 9 Output equation – Main dimensions – Choice of specific loadings – Design of stator – Design of squirrel cage and slip ring rotor – Equivalent circuit parameters from designed data – Losses and efficiency calculations. UNIT V SYNCHRONOUS MACHINES 9 Output equation – Choice of specific loadings – Main dimensions – Short circuit ratio – Design of stator and rotor of cylindrical pole and salient pole machines - Design of field coil - Performance calculation from designed data - Introduction to computer aided design. Total periods (45+15T): 60 TEXT BOOKS 1. Sawhney A.K, “A Course in Electrical Machine Design”, Dhanpat Rai and Sons, New Delhi, 2004. 2. Sen S.K, “Principles of Electrical Machine Design with Computer Programmes”, Oxford and IBH Publishing Co.Pvt Ltd., New Delhi, 1987. REFERENCES 1. Agarwal R.K, “Principles of Electrical Machine Design”, S.K.Kataria and Sons, Delhi, 2009. 2. Mittle V.N and Mittle A, “Design of Electrical Machines”, Standard Publications and Distributors, Delhi, 2002. Page 36 of 85
  37. 37. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2602 POWER SYSTEM ANALYSIS 3 1 0 4 AIM To become familiar with the modeling of various power system components and different methods of analysis for power system planning and operation. OBJECTIVES · To model steady-state operation of large-scale power systems and to solve the power flow problems using efficient numerical methods suitable for computer simulation. · To model and analyse power systems under abnormal (fault) conditions. · To model and analyse the dynamics of power system for small-signal and large signal disturbances and o design the systems for enhancing stability. UNIT - I INTRODUCTION 9 Overview of Power System Analysis: Importance of system planning and operational analysis; Distinction between steady state, quasi steady state and transient analysis; Per phase analysis of symmetrical three phase system, single line diagram, per UNIT representation; different models for generator, load and transmission lines based on the analysis of interest – π equivalent circuit of transformer with off nominal-tap ratio. UNIT - II BASICS OF ANALYSIS AND COMPONENT MODELLING 9 Primitive network and its matrices, bus admittance matrix formation by inspection method and singularity transformation method, bus impedance matrix formation by L-U factorisation of bus admittance matrix and by building algorithm. Symmetrical component transformation, sequence impedances and sequence networks. UNIT - III POWER FLOW ANALYSIS 9 Importance of power flow analysis in planning and operation of power systems; Power flow problem: Description of the problem, classification of buses into P-Q buses, P-V (voltage-controlled) buses and slack bus. Power flow equations and solution: Development of power flow model in complex variable form, Iterative solution using Gauss- Seidel and Newton-Raphson methods including Q-limit check for voltagecontrolled buses, flow chart- numerical examples. UNIT - IV FAULT ANALYSIS 9 Symmetrical short circuits: Thevenin”s theorem and applications, short circuit analysis - Numerical examples. Short circuit capacity - Circuit breaker selection. Unsymmetrical short circuits: Derivation of fault current for LG, LL, LLG short circuits and development of interconnection of sequence networks. UNIT - V STABILITY ANALYSIS 9 Description of power system stability problem; importance of stability analysis in power system planning and operation; classification of power system stability. Single Machine Infinite Bus (SMIB) system: Development of swing equation; power-angle equation; Equal Area Criterion; determination of critical clearing angle and time; algorithm for numerical solution of swing equation using modified Euler method; usage of numerical algorithm for determination of critical clearing time by trial and error – Digital simulation. Total periods (45+15T): 60 TEXT BOOKS 1. Hadi Saadat, “Power System Analysis”, Tata McGraw Hill Publishing Company Ltd., 2nd Edition, New Delhi, 2009. 2. John J. Grainger and W.D. Stevenson Jr., “Power System Analysis”, Tata McGraw Hill Publishing Company Ltd., New Delhi,2003. 3. Kothari D.P, Nagarath I.J., “Power System Engineering”,Tata McGraw-Hill Publishing Company Ltd., 2nd Edition, NewDelhi, 2008. REFERENCES Page 37 of 85
  38. 38. For the students admitted from the Academic year 2012-2013(R 2012) 1. Kundur P, “Power System Stability and Control, Tata McGraw-Hill Publishing Company Ltd., New Delhi, 1994. 2. Nagrath I.J. and Kothari D.P., “Modern Power System Analysis”, Tata McGraw-Hill Publishing Company Ltd., 3rd Edition, New Delhi, 2003. 3. Olle. I. Elgerd, “Electric Energy Systems Theory – An Introduction”, Tata McGraw Hill Publishing Company Limited, 2nd Edition, New Delhi, 2008. Page 38 of 85
  39. 39. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2603 POWER ELECTRONICS 3 1 0 4 AIM To introduce the application of electronic devices for conversion, control and conditioning of electric power. OBJECTIVES · To get an overview of different types of power semi-conductor devices and their switching characteristics. · To understand the operation, characteristics and performance parameters of controlled rectifiers. · To study the operation, switching techniques and basic topologics of DC-DC switching regulators. · To learn the different modulation techniques of pulse width modulated inverters and to understand the harmonic reduction methods. · To know the practical application for power electronics converters in conditioning the power supply. UNIT - I POWER SEMI-CONDUCTOR DEVICES 9 Structure, operation and characteristics of SCR, TRIAC, power transistor, MOSFET and IGBT. Driver and snubber circuits for MOSFET - Turn-on and turn-off characteristics and switching losses. UNIT - II LINE COMMUTATED CONVERTERS 9 2,4 pulse converter with R,RL,RLE loads, effect of free wheeling diode – continuous and discontinuous conduction mode - Effect of source inductance and load inductance – introduction to 3,6 pulse converter - Dual converters- Series converters. Basic principle of operation of single phase cycloconverter- AC voltage controllers. UNIT - III DC TO DC CONVERTERS 9 Step-down and step-up choppers - Time ratio control and current limit control – class of choppers - Switching mode regulators: Buck, boost, buck-boost and cuk converter - Resonant switching based SMPS. UNIT - IV INVERTERS 9 Single phase and three phase (both 1200 mode and 1800 mode) inverters - PWM techniques: Sinusoidal PWM, modified sinusoidal PWM and multiple PWM - Voltage and harmonic control - Series resonant inverter - Current source inverters. UNIT - V APPLICATIONS 9 Uninterrupted power supply topologies - Flexible AC transmission systems - Shunt and series static VAR compensator - Unified power flow controller- HVDC Transmission. Total periods (45+15T): 60 TEXT BOOKS 1. Bimbhra P.S, “Power Electronics” , Khanna Publishers, New Delhi, 2012 2. Singh M.D, Khandchandni K.B, Power Electronics, Tata Mc Graw Hill, 2nd Edition, 2007 REFERENCES 1. Muhammad H. Rashid, “Power Electronics: Circuits, Devices and Applications”, Pearson Education, 3rd edition, 2004 / PHI 2. Cyril.W.Lander, “Power Electronics”, McGraw Hill International, 3rd edition, 1994 3. Bimal K. Bose, “Modern Power Electronics and AC Drives”, Pearson Education, 2003 4. Jagannathan V., “Introduction to Power Electronics”, Prentice Hall of India, 2004 Page 39 of 85
  40. 40. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2604 EMBEDDED SYSTEM DESIGN 3 0 0 3 AIM To understand the basic concepts of embedded system design and its applications to various fields. OBJECTIVES To provide a clear understanding of · Embedded system terminologies and its devices. · Various Embedded software Tools · Design and architecture of Memories. · Architecture of processor and memory organizations. · Input/output interfacing · Various processor scheduling algorithms. · Basics of Real time operating systems. · Introduction to PIC and its applications. UNIT - I INTRODUCTION TO EMBEDDED SYSTEMS 9 Introduction to embedded real time systems – The build process for embedded systems – Types of memory – Memory management methods. UNIT - II EMBEDDED SYSTEM ORGANIZATION 9 Structural UNITs in processor , selection of processor & memory devices – DMA – I/O devices : timer & counting devices – Serial communication using I2C , CAN USB buses – Parallel communication using ISA , PCI ,PCI/X buses – Device drivers UNIT - III PROGRAMMING AND SCHEDULING 9 Intel I/O instructions – Synchronization - Transfer rate, latency; interrupt driven input and output - Nonmaskable interrupts, software interrupts, Preventing interrupts overrun - Disability interrupts. Multithreaded programming – Context Switching, Preemptive and non-preemptive multitasking, semaphores. Scheduling-thread states, pending threads, context switching UNIT - IV REAL-TIME OPERATING SYSTEMS 9 Introduction to basic concepts of RTOS, UNIX as a Real Time Operating system – Unix based Real Time operating system - Windows as a Real time operating system – POSIX – RTOS-Interrupt handling - A Survey of contemporary Real time Operating systems:PSOS, VRTX, VxWorks, QNX, чC/OS-II, RT Linux – Benchmarking Real time systems – Basics. UNIT - V PIC MICROCONTROLLER BASED EMBEDDED SYSTEM DESIGN 9 PIC microcontroller – MBasic compiler and Development boards – The Basic Output and digital input – Applications Total periods: 45 TEXT BOOKS 1. Rajkamal, “Embedded system-Architecture, Programming, Design”, Tata Mc graw Hill, 2nd Edition, 2008. 2. Daniel W. Lewis ,”Fundamentals of Embedded Software”, Pearson College Division, 2nd Edition, 2012. REFERENCES 1. Jack R Smith “Programming the PIC microcontroller with MBasic” Elsevier, 2005 2. Tammy Noergaard, “Embedded Systems Architecture”, Elsevier, 2005 3. Rajib Mall “Real-Time systems Theory and Practice” Pearson Education, 2007 4. Sriram. V.Iyer & Pankaj Gupta, “Embedded real time systems Programming”, Tata McGraw Hill, 2004. Page 40 of 85
  41. 41. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2605 MANAGEMENT CONCEPTS AND PRACTICES 3 0 0 3 AIM To expose the students to Management concepts and techniques. OBJECTIVE Knowledge on the management concepts is essential for all kinds of people in all kinds of organizations. After studying this course, students will be able to have a clear understanding of the basic concepts and functions of management, human resource management, Marketing Management & Financial Management, accounting concepts, Management Information System & Production/Operations, Social and Ethical Issues in Management. Students will also gain some basic knowledge on international aspect of management. UNIT - I BASIC CONCEPTS AND FUNCTIONS OF MANAGEMENT 9 Planning: Nature Purpose and OBJECTIVEs of Planning; Organizing; Nature and Purpose of Organizing; Authority and Responsibility; Staffing, Supply of Human Resources; Performance Appraisal; Controlling; System and Process of Controlling; Control Techniques. UNIT - II HUMAN RESOURCE MANAGEMENT 9 Nature and Scope of Human Resource Planning; Training and Development : Recruitment and Selection; Career Growth; Absenteeism: Grievances; Motivation and its Types; Need for Motivation: Reward and Punishment; Models of Motivation; Leaders; Kinds of Leaders, Leadership Styles, roles and Functions of Leaders; Conflict Management; Kinds and ; Causes of Conflict; Settlement of Conflicts. Group and Team Working, organizational Design and Development. UNIT–III MARKETING MANAGEMENT & FINANCIAL MANAGEMENT, ACCOUNTING CONCEPTS 9 Marketing Environment: Consumer Markets and Buyer Behaviour; Marketing Mix, Advertising and Sales Promotions; Channels of Distribution. Financial Management and Accounting Concepts Book Keeping; Financial Statements Analysis: Financial Ratios: Capital Budgeting: break-even Analysis Production/Operations Management Planning and Design of Production and Operations Systems; Facilities Planning Location, Layout and Movement of materials; Materials Management and Inventory Control; Maintenance Management PERT & CPM. UNIT– IV MANAGEMENT INFORMATION SYSTEM & PRODUCTION/OPERATIONS MANAGEMENT 9 Role of Information in decision making; Information System Planning, Design and Implementation Evaluation and Effectiveness of the Information System. Statistical Quality Control, Total Quality Management and ISO Certification. Production/Operations Management: Planning and Design of Production and Operations Systems; Facilities Planning Location, Layout and Movement of materials; Materials Management and Inventory Control; Maintenance Management PERT & CPM. UNIT - V SOCIAL AND ETHICAL ISSUES IN MANAGEMENT 9 Ethics in Management, Social Factors; Unfair and Restrictive Trade Practices. Strategic and Technology Management Need, Nature, Scope and Strategy SWOT analysis, value chain concept. Total periods: 45 TEXT BOOKS 1. Kotler Philip, “Marketing Management”, Prentice Hall of India, 11th Edition, 2003. 2. Luthans Fred, “Human Resource Management”, McGraw-Hill Inc., 1997 3. Robbins Stephen, P., “Organizational Behaviours Concepts, Controversies and Application”, Prentice Hall, Englewood, Cliffs, New Jersey, 2010. 4. Khan, M.Y. & Jain, P.K., “Financial Management”, Tata McGraw-Hill, 4th Edition, 2004. Page 41 of 85
  42. 42. For the students admitted from the Academic year 2012-2013(R 2012) REFERENCES 1. Porter Michael, “Competitive Advantage”, The Free Press, 1985. 2. Porter Micheal, “Competitive Strategy”, The Free Press, 1980. 3. Bhushan, Y.K., “Fundamentals of Business Organization and Management”, Sultan Chand and Sons, 1965. 4. Ahuja, K.K., “Industrial Management”, Khanna Publishers, 1998. Page 42 of 85
  43. 43. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2607 CONTROL SYSTEMS LABORATORY 0 0 3 2 AIM To provide a platform for understanding the basic concepts of control system and to apply them for the design and control of practical systems. OBJECTIVES After successful completion of this course, the students will be able to, · Experimentally determine transfer functions of practical systems. · Obtain the step response of practical systems. · Carry out the stability analysis of practical systems. · Design PID controller for practical systems. List of EXPERIMENTS 1. Open loop and closed loop speed control of dc servo motor. 2. Determination of transfer function of armature controlled DC servomotor. 3. Determination of transfer function of AC servomotor. 4. Determination of transfer function of a third order (or higher order) system from its frequency response. 5. Determination of transfer function of a higher order system with two or more sub systems. 6. Step response of type-0 and type-1 UNITy feedback first and second order systems. 7. Stability analysis of third order (or higher order) systems. 8. Design of a second order (or third order) system for the desired specifications. 9. Design of PID controller for a given system. 10. Study of any one closed-loop control system such as dc position control, temperature control water level control systems. 11. MATLAB simulation of step response of LTI systems. 12. Stability analysis of LTI systems using Root locus, Bode and Nyquist plots. Practical 45 Page 43 of 85
  44. 44. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2608 DSP AND MICROPROCESSORS LABORATORY 0 0 3 2 AIM To expose the students to gain programming skills in DSP and Microprocessors. DSP 1. Generation of basic sequences using MATLAB UNIT sample sequence UNIT step sequence UNIT ramp sequence 2. Computation of Fast Fourier Transform using MATLAB DIT – FFT algorithm DIF – FFT algorithm 3. Design and simulation of FIR filter using windowing technique 4. Design and simulation of IIR filter using Bilinear Transformation and Impulse Invariant method. 5. Generation of following waveforms using TMS320C50 trainer Kit Sine wave Square wave Saw tooth wave Triangular wave 6. Linear convolution and circular convolution using TMS320C50 trainer Kit MICROPROCESSORS: 1. Simple arithmetic operations: Multi precision addition / subtraction / multiplication / division. 2. Programming with control instructions: Increment / Decrement. Ascending / Descending order. Maximum / minimum of numbers. 3. Rotate instructions. Hex / ASCII / BCD code conversions. 4. Interface EXPERIMENTS: A/D Interfacing. D/A Interfacing. Traffic light controller. 5. Interface EXPERIMENTS: Simple EXPERIMENTS using 8251, 8279, 8253, and 8254. 6. Programming practice on assembler and simulator tools. Practical 45 Page 44 of 85
  45. 45. For the students admitted from the Academic year 2012-2013(R 2012) VII SEMESTER 12EE2701 ELECTRIC ENERGY GENERATION, UTILISATION AND CONSERVATION 3 0 0 3 AIM To expose the students to the main aspects of electric energy generation, utilization and conservation. OBJECTIVES To impart knowledge on · Conventional methods of generation and conservative methods. · Principle and design of illumination systems and · Methods of heating and welding · Electric traction systems and their performance. · Industrial applications of electric drives. UNIT - I GENERATION 9 Generation of electrical power by conventional methods – Introduction to the concept of distributed generation – Effect on system operation. UNIT - II CONSERVATION 9 Economics of generation – Definitions – Load curves – Number and size of UNITs – Cost of electrical energy – Tariff – Need for electrical energy conservation – Methods – Energy efficient equipment – Energy management – Energy auditing. Economics of power factor improvement – Design for improvement of power factor using power capacitors – Power quality – Effect on conservation. UNIT - III ILLUMINATION 9 Definition and meaning of terms used in illumination Engineering – Classification of light sources – Laws of illumination - Nature of radiation – Photometry – Lighting calculations – Design of illumination systems (for residential, industrial, commercial, health care, street lightings, sports, administrative complexes) - Types of lamps: Incandescent lamps, sodium vapour lamps, mercury vapour lamps, fluorescent lamps - Energy efficiency lamps. UNIT - IV HEATING AND WELDING 9 Introduction – Advantages of Electric heating – Modes of heat transfer – Methods of heating, requirement of heating material – Design of heating element – Furnaces – Welding generator – Welding transformer and its characteristics. Requirements of good weld – Preparation of work – Electrodes – Power supply for arc welding. UNIT - V ELECTRIC TRACTION 9 Introduction – Requirements of an ideal traction system – Supply systems – Mechanics of train movement – Traction motors and control – Multiple UNITs – Braking – Current collection systems – Recent trends in electric traction. Total periods: 45 TEXT BOOKS 1. Openshaw Taylor E, “Utilization of Electrical Energy in SI UNITs”, Orient Longman Pvt.Ltd, 2003. 2. Gupta B.R, “Generation of Electrical Energy”, Eurasia Publishing House (P) Ltd, New Delhi, 2009. REFERENCES 1. Partab H, “Art and Science of Utilisation of Electrical Energy”, Dhanpat Rai and Co, New Delhi, 2004 2. Gopal.K.Dubey, “Fundamentals of Electrical Drives”, Narosa Publishing House, New Delhi, 2nd edition, 2004. Page 45 of 85
  46. 46. For the students admitted from the Academic year 2012-2013(R 2012) 3. Wadhwa C.L, “Generation, Distribution and Utilization of Electrical Energy”, New Age International Pvt.Ltd,2nd Edition, 2003 4. Gupta J.B, “Utilization of Electric Power and Electric Traction”, S.K.Kataria and Sons, 2002. Page 46 of 85
  47. 47. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2702 ELECTRIC DRIVES AND CONTROL 3 0 0 3 AIM To expose the students to the concepts of electric drives and controls. OBJECTIVES · To learn about basic concepts of electric drives. · To learn about different types of DC drives. · To study about Induction motor drives. · To learn about special machines drives. · To understand design of controllers for drives. UNIT - I Introduction to Electric Drives 9 History and development of Electric Drives, Classification of Electric Drives, Basic elements & advantages of variable speed drives- Joint Speed-Torque characteristics of various types of loads and drive motors- Modes of operation, closed loop control of drives - Selection of power rating for drive motors with regard to thermal overloading and load variation-Load Equalization. UNIT - II Dc Drives 9 Speed control of DC motors - Ward - Leonard scheme - drawbacks - Thyristor converter fed dc drives: Single, two and four quadrant operations - Chopper fed DC drives : - Time ratio control and current limit control - Single, two and four quadrant operations – Effect of ripples on the motor performance. UNIT - III Three Phase Induction Motor Drives 9 Speed control of 3 phase Induction Motors - Stator control: PWM &V/f control, rotorcontrol: Rotor resistance control - Static control of rotor resistance using DC chopper - Static Krammer and Scherbius drives – Introduction to Vector Controlled Induction Motor Drives. UNIT - IV Drives for Special Machines 9 Speed control of 3 phase Synchronous Motors - True synchronous and self controlled modes of operations - DC servo drives principle of operation AC servo drives principle of operation - Principle and control of Stepper motor and Switched Reluctance Motor drives. UNIT - V Digital Control and Drive Applications 9 Digital techniques in speed control - Advantages and limitations - Microprocessor/Microcontroller and PLC based control of drives, networking of drives - Selection of drives and control schemes for Steel rolling mills, Paper mills, Cement mills, Machine tools, Lifts and Cranes. Solar and battery powered drives. Total periods: 45 TEXT BOOKS 1. Dubey, G.K., “Fundamentals of Electrical Drives”, Narosa Publishing House, 2nd Edition, New Delhi, 2004. 2. Bose, B.K., “Modern Power Electronics and AC Drives", Prentice Hall India Ltd., New Delhi, 2002. REFERENCES 1. Ion Boldea and Nasar S. A., “Electric Drives”, CRC Press LLC, New York, 2nd Edition, 2006. 2. Krishnan R, “Electric Motor Drives: Modelling, Analysis and Control, Prentice Hall of India Pvt. Ltd., New Delhi, 2002. 3. Vedam Subramanyam, “Electric Drives: Concepts and Applications”, Tata McGraw Hill Publishing Company Limited, New Delhi, 2004. Page 47 of 85
  48. 48. For the students admitted from the Academic year 2012-2013(R 2012) 12EE2703 POWER SYSTEM ECONOMICS AND CONTROL TECHNIQUES 3 1 0 4 AIM To become familiar with the preparatory work necessary for meeting the next day’s power system operation and the various control actions to be implemented on the system to meet the minute-to-minute variation of system load. OBJECTIVES · To get an overview of system operation and control. · To understand & model power-frequency dynamics and to design power-frequency controller. · To understand & model reactive power-voltage interaction and different methods of control for maintaining voltage profile against varying system load. UNIT - I INTRODUCTION 9 System load variation: System load characteristics, load curves daily, weekly and annual, load-duration curve, load factor, diversity factor. Reserve requirements: Installed reserves, spinning reserves, cold reserves, hot reserves. Overview of system operation: Load forecasting, UNIT commitment, load dispatching. Overview of system control: Governor Control, LFC, EDC, AVR, system voltage control, security control. UNIT - II REAL POWER - FREQUENCY CONTROL 8 Fundamentals of speed governing mechanism and modeling: Speed-load characteristics – Load sharing between two synchronous machines in parallel; concept of control area, LFC control of a single-area system: Static and dynamic analysis of uncontrolled and controlled cases, Economic Dispatch Control. Multi-area systems: Two-area system modeling; static analysis, uncontrolled case; tie line with frequency bias control of two-area system derivation, state variable model. UNIT - III REACTIVE POWER–VOLTAGE CONTROL 9 Typical excitation system, modeling, static and dynamic analysis, stability compensation; generation and absorption of reactive power: Relation between voltage, power and reactive power at a node; method of voltage control: Injection of reactive power. Tap-changing transformer, numerical problems - System level control using generator voltage magnitude setting, tap setting of OLTC transformer and MVAR injection of switched capacitors to maintain acceptable voltage profile and to minimize transmission loss. UNIT - IV UNIT COMMITMENT AND ECONOMIC DISPATCH 9 Statement of UNIT Commitment (UC) problem; constraints in UC: spinning reserve, thermal UNIT constraints, hydro constraints, fuel constraints and other constraints; UC solution methods: Priority-list methods, forward dynamic programming approach, numerical problems only in priority-list method using full-load average production cost. Incremental cost curve, co-ordination equations without loss and with loss, solution by direct method and λ- iteration method. (No derivation of loss coefficients.) Base point and participation factors. Economic dispatch controller added to LFC control. UNIT - V COMPUTER CONTROL OF POWER SYSTEMS 10 Energy control centre: Functions – Monitoring, data acquisition and control. System hardware configuration – SCADA and EMS functions: Network topology determination, state estimation, security analysis and control. Various operating states: Normal, alert, emergency, inextremis and restorative. State transition diagram showing various state transitions and control strategies. Total periods (45+15T): 60 TEXT BOOKS 1. Olle. I. Elgerd, “Electric Energy Systems Theory – An Introduction”, Tata McGraw Hill Publishing Company Ltd, New Delhi, 2nd Edition, 2008 2. Allen.J.Wood and Bruce F.Wollenberg, “Power Generation, Operation and Control”, John Wiley & Sons, Inc., 2003 3. Kundur P, “Power System Stability & Control”, Tata-McGraw Hill publications,USA,2005 Page 48 of 85

×