The document discusses forklift safety and provides guidance on proper forklift operation. It covers the forklift stability triangle and center of gravity, load capacities, safely lifting and moving loads, personnel safety, travelling on inclines, loading trucks, factors contributing to accidents, and performing a forklift circle check. Maintaining forklift stability and paying attention to load capacities and weights are emphasized as important safety practices.
2. FORKLIFT STABILITY TRIANGLE - CENTER OF
GRAVITY
• Forklifts have a “stability triangle”.
• The sides of the stability triangle as shown
in the illustration are formed by the center
of each front wheel and the center of the
rear wheel or at the center of the axle if
there are two rear wheels.
• A vertical line extending from the center of
gravity of the vehicle-load combination
must be inside of the stability triangle to
prevent the forklift from tipping forward,
falling sideways or dropping its load.
Stability triangle center of gravity Forklift safety Stability Triangle Diagram
5. Locate data plate and obey the load capacity of the forklift and its attachments.
Do not overload your truck or add extra counterweight.
Match your speed to the surface being driven on, load and workplace conditions.
Exceeding forklift capacity is just asking
for trouble
Unstable loads are no match for gravity
when you apply the brakes
PAY CLOSE ATTENTION TO CAPACITIES TO AVOID POSSIBLE ACCIDENTS
SAFELY LIFTING AND MOVING A LOAD
6. Capacity Forklift Type Attachment ID
Capacity with
Attachment
SAFELY LIFTING AND MOVING A LOAD
This LP Gas Forklift can safely lift 5000 Lbs. 173" high
with a center of gravity 24" from the face of the forks.
With an attachment labeled "HSS", the safe load drops to 4500 Lbs.
Data plate load capacity forklift
7. SAFELY LIFTING AND MOVING A LOAD
Ensure the forks are level and high enough to go
into the pallet but not puncture the load.
Place forks as far under the load as possible
while keeping in mind the length of the forks
and objects behind the load.
Lift the load straight up until it is clear, then tilt
back, drive with the load against the backrest.
Watch that the load or forks do not catch on
adjacent loads or obstructions.
8. Allow safe working distance between forklifts.
Do not pass a forklift travelling in the same
direction at intersections, blind spots or other
dangerous locations.
Stay constantly alert to changing or unusual
conditions.
Do not permit anyone to stand or walk under the
elevated part of any forklift, whether loaded or
unloaded.
SAFELY LIFTING AND MOVING A LOAD
9. SAFELY LIFTING AND MOVING A LOAD
Check operating
clearance space.
Watch for overhead
obstructions.
Avoid driving over loose
objects or on surfaces
with ruts and holes.
Avoid abrupt hydraulic
system movement which
could rupture hydraulic
hoses or de-stabilize the
load.
LOOK FOR OVERHEAD HAZARDS BOTH
WHEN LIFTING A LOAD AND WHILE
TRAVELLING.
10. SAFELY LIFTING AND MOVING A LOAD
Do not operate forklift without load
backrest or overhead guard.
Do not lift a load that extends above
the load backrest unless no part of the
load can possibly slide back toward the
operator.
Do not move loads which are poorly
piled or stacked.
11. SAFELY LIFTING AND MOVING A LOAD
ONLY raise or lower the forks when stopped and brakes
applied.
When depositing a load, ensure the forks are free of the
load before you back up.
Stack materials properly for safe and efficient retrieval.
Be alert for materials which may have been stored
improperly.
Use extreme care when tilting loads.
Tilting elevated forks forward shall be prohibited except
when picking up a load or where the load is to be
deposited.
Keep heavier materials near floor.
12. SAFELY LIFTING AND MOVING A LOAD
Match your speed to the surface being driven
on, load being carried and workplace
conditions.
Do not start, stop, turn or change direction
suddenly or at speed.
Stack items so that they do not extend into
aisles.
When forks are empty, mast should be tilted
back to prevent tips of forks from contacting
ground, or other obstacles.
Notify supervisor if a hazardous substance is
spilled, follow proper procedure for clean up.
13. PERSONNEL AND PEDESTRIAN SAFETY
Do not use pallets elevated by
forklifts as an improvised working
platform.
Do not elevate anyone on forks
unless in approved man cage that is
secured to forklift.
DON'T TAKE CHANCES LIFTING PERSONNEL
WITHOUT PROPER LIFT CAGE SECURELY ATTACHED
TO LIFTING EQUIPMENT.
14. Use of Mirror PERSONNEL AND PEDESTRIAN
SAFETY
Use mirrors, sound horn and slow down
when approaching pedestrians, hazardous
passageways and work areas.
When forks are empty, mast should be
tilted back to prevent tips of forks from
contacting ground, or other obstacles.
Match your speed to the surface being
driven on, load and workplace conditions.
Do not start, stop, turn or change direction
suddenly or at speed.
15. PERSONNEL AND PEDESTRIAN SAFETY
Do not try to move or adjust any
part of the load, the forklift or the
surroundings while on the forklift.
Do not climb between mast and
load or between mast and
machine
16. PERSONNEL AND PEDESTRIAN SAFETY
Do not drive with hands, arms,
head, legs or feet outside the
confines of the forklift or between
mast uprights or other parts of the
unit where shear or crushing
hazards exist.
Only operate controls while sitting
in the operator’s seat.
17. TRAVELLING ON INCLINES
Know the forklift wheel position and
your direction of travel in relation to
loading docks, trucks, and platforms.
When travelling up or down an incline
with a load, keep the load pointed uphill.
When driving up or down an incline
without a load, keep the forks pointed
downhill.
Do not turn until you are on level ground.
Fatal forklift accident, fork lift tipped over
crushing driver
18. TRAVELLING ON INCLINES
Forklift carrying load up or down incline
keeps forks uphill
Forklift with no load up or down incline
keeps forks downhill
19. TRAVELLING ON INCLINES
If you ever begin to tip, DON’T JUMP OUT
! ! ! Brace yourself, hold steering wheel
tightly with both hands, push yourself
into the seat and lean away from the fall.
Most forklift fatalities are due to crushing
injuries when driver becomes pinned
under part of the machine.
Scene of fatal tow motor tip over forklift
accident
20. LOADING TRUCKS
Ensure that truck and trailer brakes are set and wheels are
blocked.
Trailers not hooked to a tractor at a dock should be secured
by trailer jacks or sufficient support.
21. LOADING TRUCKS
Watch for holes or weak floors.
Watch for trash, loose objects and
obstructions.
Inspect condition of truck or
trailer before entering.
Ensure the floors will support the
combined weight of the forklift
and the load.
ALWAYS OBSERVE THE CONDITION OF THE TRAILER
BEFORE ENTERING
23. LOADING TRUCKS
Do not allow pedestrians in trailers while a lift truck is loading or unloading.
The likelihood of being crushed by a forklift is greater in tight spaces.
Ensure proper lighting in trailer and work area.
AVOID THE PITFALLS OF AN UNSTABLE OR OVERWEIGHT LOAD
24. LOADING TRUCKS
Never park a forklift on a dock
plate.
Ensure that portable dock plates
are properly secured before
driving over.
Ensure plate capacity is
capable of supporting forklift
and load.
Dock levelers must be extended
and securely resting on trailer
floor
25. LOADING TRUCKS
Install anti-slipping material in any
area that could be a hazard due to
weather conditions.
Ensure that docks and dock plates
are clear of obstructions and not
oily, wet or coated with ice or
snow.
Know where to find safety salt, ice
melter or oil absorbent.
HAVE A POLICY IN PLACE TO PREVENT TRUCK
PULLING OUT PREMATURELY
26. FACTORS CONTRIBUTING TO TOW MOTOR
AND FORKLIFT ACCIDENTS
Behavioural / Operational Factors
Excessive speed
Lack of worker training.
Improper vehicle restraints on
trucks and trailers.
Inadequate servicing of the forklift
Improper backing, turning, braking.
Improperly parking the forklift.
27. FACTORS CONTRIBUTING TO TOW MOTOR
AND FORKLIFT ACCIDENTS
Walking and working in the general area of
forklift operations.
Poor communication during shared tasks,
or in shared spaces.
Improper warnings to others of forklift
presence.
Allowing passengers on the forklift or load.
Non-acceptable behaviours, horseplay,
showing off
NEVER TAKE SAFETY FOR GRANTED,
ACCIDENTS CAN HAPPEN ANYWHERE,
ANYTIME.
28. FACTORS CONTRIBUTING TO TOW MOTOR
AND FORKLIFT ACCIDENTS
Characteristics of the
Workplace
Narrow, crowded, or cluttered aisles.
Intersections and doorways.
Concentrations of traffic.
Type of materials being stored or
moved.
Visibility restrictions and
obstructions
29. FACTORS CONTRIBUTING TO TOW MOTOR
AND FORKLIFT ACCIDENTS
Lighting conditions, shadows and
glare.
Condition of loading dock.
Ramps, inclines or different
surface conditions.
Potholes or obstacles on the
ground Other factors - noise,
odours, toxic gases, dust.
30. FACTORS CONTRIBUTING TO TOW MOTOR
AND FORKLIFT ACCIDENTS
Operational Systems
Production factors - speed, stress, lack
of proper attachments or accessories
Policies and procedures
Age of forklifts.
Maintenance program.
KNOW YOUR WORK AREA, LEARN THE HAZARDS
31. FACTORS CONTRIBUTING TO TOW MOTOR
AND FORKLIFT ACCIDENTS
Characteristics of the Load
Poor palletizing.
Damaged Skids.
Load too heavy.
Load unstable.
Load blocking vision.
NEVER TRY TO MOVE AN UNSTABLE LOAD,
FIX IT FIRST!
32. FORKLIFT CIRCLE CHECK
BE THOROUGH, BE SAFE Daily Visual and Operational Safety
Inspection
An individual checklist should be developed for each
machine tailored to the make, model and attachments of the
machine.
33. FORKLIFT CIRCLE CHECK
Walk around the forklift, checking for obstructions or hazards in
the area, fluid leaks, damp spots or drips.
Check condition of wheels/tires.
Inspect belts, hoses and connections.
Check propane, engine oil, coolant level and battery condition.
34. FORKLIFT CIRCLE CHECK
Lights working properly.
Fire extinguisher-present and charged.
Foot brake pedal holds, unit stops
smoothly.
Parking brake should hold against
slight acceleration.
Dash control panel all lights, gauges
and horn operational.
35. FORKLIFT CIRCLE CHECK
Clutch and gearshift smooth shifting no jumping or
jerking.
Steering functioning properly, no excessive play in the
wheel.
36. FORKLIFT CIRCLE CHECK
No external or internal leaks at lift and tilt
cylinders. also, no leaking hydraulic
hoses.
Chains, rollers, hose pulleys in good
shape.
37. FORKLIFT CIRCLE CHECK
Check forks for positioning, latches and anchor pins worn, loose or bent.
Beware of damaged, cracked or bent forks.