Dye removal from waste water by using low cost adsorbent: A review
1. Dye removal from waste water by using low cost adsorbent: A review
Submitted to
National Conference
on
Emerging Research Trends in Engineering-2016
Paper ID - 125
Chemical Engineering Department
Vishwakarma Government Engineering College
Chandkheda-382424
Year: – 2016
3. 1. Introduction
•The quality of our water resources is getting worse and use of dyes
generates colored wastewaters, which give cause of environmental concern.
•Textile wastewater includes a large variety of dyes and chemical additions
that make the environmental challenge for textile industry not only as liquid
waste but also in its chemical composition.
•Main pollution in textile wastewater come from dyeing and finishing
processes.
•These processes require the input of a wide range of chemicals and
dyestuffs, which generally are organic compounds of complex structure.
4. •Water is used as the principal medium to apply dyes and various
chemicals for finishes.
•Because all of them are not contained in the final product, became waste
and caused disposal problems.
•Major pollutants in textile wastewaters are high suspended solids,
chemical oxygen demand, heat, colour, acidity, and other soluble
substances.
•Substances which need to be removed from textile wastewater are mainly
colour, COD, BOD, pH, TDS.
6. Permissible Limits
• pH is 6.5-8.5
• The maximum permissible COD limit is < 150 mg/L
• The maximum permitted BOD content of < 100 mg/L.
• TDS limit is 2100 mg/L
• Color limit 100 hazen
7. The Technologies
Treatment methods for effluents
Chemical methods Physical methods Biological methods
Oxidation Ozonation Filtration
Coagulation/
Flocculation
Adsorption
Microbes
Enzymes
8. • A process wherein a material is concentrated at a solid surface from
its liquid or gaseous surroundings.
• Adsorption is considered as the best wastewater treatment technique
because of its all-inclusive nature, modesty and simplicity of
operation.
• Basically, adsorption is the accumulation of a substance at a surface
or interface.
2. Adsorption
9. • Simplest
• Low capital and operating costs
• Can have good physical properties
• Adsorbents are easily available
Why Adsorption ??
10. Adsorption processes: Applications
Purifications:
- Removal of organics from
vent gases
- SO2 from vent gases
- H2O from air, methane, N2
- Removal of solvent, odours
from air
- NOx from N2
- Organics from water solution
- Water from organic solution
- Decolourization
Separations:
- N2/O2
- Acetone from vent stream
- C2H4 from vent
- Normal paraffins/ Iso praffins
- CO, CH4, CO2, N2, Ar from
hydrogen
- Normal paraffins from Iso paraffins
- Normal paraffins from olefins
gasphaseliquidphase
11. • Adsorption processes is the interaction of adsorbate molecules
with the surface of adsorbent
• Therefore adsorbent materials are usually materials with
extensive porous structure
Criteria for adsorbent selection:
* Selectivity
* Capacity
* Chemical and thermal stability
* Cost
3. Adsorbent
12. (I) On basis of their availability
(a) Natural materials
(b) Industrial/Agricultural/ Domestic wastes or by-products
(c) Synthesized products
(II) Depending on their nature
(a) Inorganic
(b) Organic
An application of bio-sorption using fungi, yeasts and bacteria for the
removal of organic pollutants
Classification of adsorbents
13. Adsorbents: Characterization
1) Crystalline/amorphous
2) Hydrophobic/Hydrophilic
3) Surface area (100-1000 m2/gm)
4) Pore size
5) Pore shape: slits, channels, cavities, cages, shapeless
- often modelled as cylindrical channels
r < 2 nm Microporous
2 nm < r < 50 nm Mesoporous
r > 50 nm Macroporous
14. Factors Affecting Adsorbents Properties
• Starting materials (e.g., coal vs. wood based) and activation
• Pores and pore size distributions
• Internal surface area
• Surface chemistry (esp. polarity)
• Apparent density
• Particle Size: Granular vs. Powdered (GAC vs. PAC)
16. 4. Literature review
Author Adsorbent Dye Parameter Isotherms and
model
Nevine Kamal Amin
(2008)
[15]
Sugarcane
bagasse pith
reactive orange (RO)
dye
contact time,
adsorbent dose
and pH
Langmuir and
Freundlich
adsorption
isotherms
V.K. Garg , Renuka
Gupta, Anu Bala Yadav,
Rakesh Kumar (2003)
[22]
Sawdust malachite green contact time,
adsorbent dose
and pH
first order rate
expression and
Lagergren
equation
K. Santhy, P. Selvapathy
(2006)
[12]
Coir pith reactive
dyes(orange12, red 2,
blue 4)
contact time,
adsorbent dose
and pH
Freundlich model
V.K. Garg, Moirangthem
Amita, Rakesh Kumar,
Renuka Gupta (2004)
[21]
Indian
Rosewood
Sawdust
methylene blue adsorbent dosage,
initial dye
concentration, pH
and contact time
first order rate
equation and fit
the Lagergren
equation
17. F. Ferrero
(2007)
[7]
Ground
hazelnut
shells and
sawdust
Methylene Blue,
and Acid Blue 25
- Lagergren’s model, but the best fit
was achieved by a second order
Equation
Freundlich and Langmuir
isotherms
P.K. Malik
(2004)
[16]
Mahogany
sawdust:
Direct Blue 2B and
Direct Green B dyes
- Langmuir equation as well as the
pseudo-second-order
rate equation
C. Namasivayam,
D. Kavitha
(2002)
[4]
Coir pith Congo Red agitation time,
dye concentration,
adsorbent dose, pH
and temperature
Langmuir and
Freundlich isotherms
Dipa Ghosh,
Krishna G.
Bhattacharyya
(2002) [5]
Kaolinite clay methylene blue pH Freundlich and Langmuir
equations
B.H. Hameed, A.L.
Ahmad, K.N.A.
Latiff
(2007) [3]
rattan
sawdust
methylene blue Effect of initial dye
concentration on
adsorption
Langmuir and Freundlich models
18. G. Atun, G. Hisarli, W.S.
Sheldrick, and
M. Muhler
(2003)
[8]
Fuller’s earth methylene blue dependence on
initial
concentration
Effect of
temperature on
MB adsorption
-
V. J. P. Poots, G. McKay,
J. J. Healy (1978)
[20]
wood Atrazone
Blue
Contact time,
initial conc of dye Langmuir and
Freundlich
models
Hung-Yee Shu, Ming-
Chin Chang
(2005)
[10]
advanced
oxidation
process
phthalocyanine dye initial hydrogen
peroxide
concentration,
Effect of UV light
power, , initial dye
concentration, pH
-
Li-yan Fu, Xiang-hua
Wen, Li-jie Xu, Yi Qian
(2002)
[13]
acclimated
sludge,
copper-
phthalocyanine dye
Influence of CPC
concentration on
microbial
activity
-
20. pH
• High pH solution results in an increase in the percentage of cationic dye
removal because the positive charge on the solution interface will decrease
and the adsorbent surface appears negatively charged.
• Low pH solution results in an increase in the percentage of anionic dye
removal because of the electrostatic attraction between anionic dye and the
positive surface charge of the adsorbent.
21. Adsorbent Dosage
• In general, the dye removal percentage is increasing with the increase
of the adsorbent dosage.
• When excess adsorbent dosage is used, a significant portion of the
adsorption sites remain unsaturated. This obviously leads to low
specific adsorption capacity.
• When the adsorbent dosage was lowered, the number of active sites
saturated with dyes increased; therefore, specific uptake also
increased.
22. Time
• At higher contact time, the rate of adsorption decreases, gradually
leading to equilibrium due to decrease in total adsorbent surface area
and less available binding sites.
• The decrease in dye removal with time may be due to aggregation of
the dye molecules around the adsorbent particles.
23. • Is an empirical relation between the concentration of a solute on the surface of an adsorbent to
the concentration of the solute in the liquid with which it is in contact.
Freundlich adsorption isotherm
• The Freundlich Adsorption Isotherm is mathematically expressed as
𝑞 = 𝐾𝑝
1
𝑛
It can be written as,
Or
𝑥
𝑚
= 𝐾𝐶
1
𝑛
log 𝑞 = log 𝐾 +
1
𝑛
log 𝐶
• Freundlich adsorption isotherm failed at higher pressure.
log 𝑞 = log 𝐾 +
1
𝑛
log 𝑝
Where, q = amount of solute adsorbed
C= eq. concentration
K= adsorption coefficient
n= slope
24. Simple isotherm equations: Langmuir
Assumptions:
- Single layer
- Interaction between
molecules in the layer are
negligible
i
i
Kp
Kp
1
i
ii
i
Kp
pKn
n
1
max
max
i
i
n
n
max
in
max
i
i
n
n
25. Simple isotherm equations: Langmuir
i
ii
i
Kp
pKn
n
1
max
maxmax
1
i
i
ii
i
n
p
Knn
p
ip
i
i
n
p
max
1
in
Kni
max
1
bY
HY
q
1
More convenient units
q [kg of adsorbate]/
[kg of pure adsorbent]
Y [kg of adsorbate/kg carrier gas]
26. Lagergren equation
• Lagergren first order model which is generally expressed as
𝑑𝑞
𝑑𝑡
= 𝑘1(𝑞 𝑒 − 𝑞)
Where, k1 is the first-order-rate constant.
• The kinetic rate expression can be written as
log(𝑞 𝑒 − 𝑞)= log 𝑞 𝑒 −
𝑘1
2.303
𝑡
27. • Low cost adsorbents can be used for water treatment and waste management.
• There is a need to develop more efficient selective, inexpensive and eco-friendly
low cost adsorbents for water treatment.
• Continuous process can be used for adsorption process.
• Many work is to be carried out in the area of desorption process.
5. Future scope
28. [1] A.L. Ahmad, S.W. Puasa, Reactive dyes decolourization from an aqueous solution by combined
coagulation/micellar-enhanced ultrafiltration process, Chemical Engineering Journal 132 (2007) 257–265.
[2] Aysegul Pala, Enis Tokat, Color removal from cotton textile industry wastewater in an activated sludge system
with various additives, Water Research 36 (2002) 2920–2925.
[3] B.H. Hameed, A.L. Ahmad, K.N.A. Latiff, Adsorption of basic dye (methylene blue) onto activated carbon
prepared from rattan sawdust, Dyes and Pigments 75 (2007) 143-149.
[4] C. Namasivayam, D. Kavitha, Removal of Congo Red from water by adsorption onto activated carbon
prepared from coir pith, an agricultural solid waste, Dyes and Pigments 54 (2002) 47–58.
[5] Dipa Ghosh, Krishna G. Bhattacharyya, Adsorption of methylene blue on kaolinite, Applied Clay Science 20
(2002) 295– 300.
[6] Esther Forgacs, Tibor Cserhati, Gyula Oros, Removal of synthetic dyes from wastewaters: a review,
Environment International 30 (2004) 953– 971.
[7] F. Ferrero, Dye removal by low cost adsorbents: Hazelnut shells in comparison with wood sawdust, Journal of
Hazardous Materials 142 (2007) 144–152.
6. References
29. [8] G. Atun, G. Hisarli, W.S. Sheldrick, and M. Muhler, Adsorptive removal of methylene blue from colored
effluents on fuller’s earth, Journal of Colloid and Interface Science 261 (2003) 32–39.
[9] Gregorio Crini, Recent developments in polysaccharide-based materials used as adsorbents in wastewater
treatment, Prog. Polym. Sci. 30 (2005) 38–70.
[10] Hung-Yee Shu, Ming-Chin Chang, Decolorization and mineralization of a phthalocyanine dye C.I. Direct
Blue 199 using UV/H2O2 process, Journal of Hazardous Materials B125 (2005) 96–101.
[11] Imran Ali, Mohd. Asim, Tabrez A. Khan, Low cost adsorbents for the removal of organic pollutants from
wastewater, Journal of Environmental Management 113 (2012) 170-183.
[12] K. Santhy, P. Selvapathy, Removal of reactive dyes from wastewater by adsorption on coir pith activated
carbon, Bioresource Technology 97 (2006) 1329–1336.Klaus Hunger (Editor), Industrial Dyes Chemistry,
Properties, Applications, 2003.
[13] Li-yan Fu, Xiang-hua Wen, Li-jie Xu, Yi Qian, Removal of a copper-phthalocyanine dye from wastewater by
acclimated sludge under anaerobic or aerobic conditions, Process Biochemistry 37 (2002) 1151–1156.
[14] Maria Cristina Silva, Angelita Duarte Correa Decolorization of the phthalocyanine dye reactive blue 21 by
turnip peroxidase and assessment of its oxidation products, Journal of Molecular Catalysis B: Enzymatic 77
(2012) 9– 14.
30. [15] Nevine Kamal Amin, Removal of reactive dye from aqueous solutions by adsorption onto activated
carbons prepared from sugarcane bagasse pith, Desalination 223 (2008) 152–161.
[16] P.K. Malik, Dye removal from wastewater using activated carbon developed from sawdust: adsorption
equilibrium and kinetics, Journal of Hazardous Materials B113 (2004) 81–88.
[17] Sanna Hokkanen, Amit Bhatnagar, Mika Sillanpaa, A review on modification methods to cellulose-based
adsorbents to improve adsorption capacity, Water Research 91 (2016) 156-173.
[18] Sarika Diwaniyan, Deepti Kharb, Chandralata Raghukumar, Ramesh Chander Kuhad, Decolorization of
Synthetic Dyes and Textile Effluents by Basidiomycetous Fungi, Water Air Soil Pollut (2010) 210:409–419.
[19] Shaobin Wang, Yuelian Peng, Natural zeolites as effective adsorbents in water and wastewater treatment,
Chemical Engineering Journal 156 (2010) 11–24.
[20] V. J. P. Poots, G. McKay and J. J. Healy, Removal of Basic Dye from Effluent Using Wood as an
Adsorbent, Journal (Water Pollution Control Federation), Vol. 50, No. 5 (May, 1978), pp. 926-935.
[21] V.K. Garg, Moirangthem Amita, Rakesh Kumar, Renuka Gupta, Basic dye (methylene blue) removal
from simulated wastewater by adsorption using Indian Rosewood sawdust: a timber industry waste, Dyes and
Pigments 63 (2004) 243-250.
31. [22] V.K. Garg, Renuka Gupta, Anu Bala Yadav, Rakesh Kumar, Dye removal from aqueous
solution by adsorption on treated sawdust, Bioresource Technology 89 (2003) 121–124.
[23] V.K. Gupta, Suhas, Application of low-cost adsorbents for dye removal – A review, Journal
of Environmental Management 90 (2009) 2313–2342.
[24] W.T. Tsai, K.J. Hsien and J.M. Yang, Silica adsorbent prepared from spent diatomaceous
earth and its application to removal of dye from aqueous solution, Journal of Colloid and
Interface Science 275 (2004) 428–433.