The document provides instructions for connecting an RM Classboard Touch interactive whiteboard to a computer via Bluetooth. It discusses downloading the necessary PolyVision software and drivers. For PCs, it describes setting the Bluetooth service to start automatically and pairing the computer to the IWB's Bluetooth adapter by entering a passcode. Once configured, the computer should automatically connect to the IWB on startup. The document also outlines calibrating the IWB screen.
2. PolyVision following computerWhite Board
Works with the
Interactive configurations:
Mac
PC with Built in Bluetooth
PC with no built in Bluetooth
Main benefits of the Bluetooth White Board:
No cable required to connect the board to the computer.
3. Caring for your PolyVision Board
DO NOT UNDER ANY CIRCUMSTANCES USE DRY
ERASE CLEANER ON THE BOARD’S SURFACE.
The board is cleaned by using soap and water mixture.
If you write on the board use only dry erase markers
and clean the board that day to insure you board will
last.
The board has a five year warranty from RM.
6. Installing the RM Classboard
Bluetooth
Bluetooth is held in place by two screws.
The RM installers should have connected this during installation.
7. Loading the PolyVision Software
You must have administrative rights to load the software.
Use the Polyvision disk that comes in the Polyvision box or
Use the Polyvision software from the Web Site
http://www.polyvision.com/Support/Downloads/tabid/232/CategoryId/18/DownloadTypeId/106/LangId/158/Default.aspx
Choose Mac or PC
9. Downloading the PolyVision
Drivers
Once drivers have been loaded, turn off the computer
completely.
Leave computer shut down for two minutes.
Insert the Polyvision Bluetooth into one of your
computer’s USB ports.
Turn on computer with Bluetooth inserted in the USB
port.
10. Stop and Read Below:
If you have a PC, please continue to the next slide for directions on
whiteboard connectivity. If you have a MAC please continue to the NEXT
Stop Sign in this presentation for connecting using your MAC computer.
11. Required Bluetooth Setting on
Laptops
On the “Start” toolbar bar, chose the Control Panel.
Once in Control Panel, chose Administrative Tools.
15. Required Bluetooth Setting on
Move to the Log On Tab, make sure to Go back to the General Tab and hit the
Laptops
chose LOCAL SYSTEM ACCOUNT. START button.
16. Connecting to the POLYVISION
Adapter to the Classboard
Bluetooth- PC Directions
Now that you the Classboard drivers dowloaded, you are
ready to connect the board with your computer. Give your
computer a chance to recognize the Polyvision bluetooth.
You will see this icon pop up in the system tray.
Step 1:
Right click on the Bluetooth icon in the system tray on your desktop.
Step 2: A similar menu will pop up, please select Add
Bluetooth Device.
17. Connectingwill appear, follow directions below:
Step 3: This screen
to the POLYVISION
Adapter- PC Directions
Select the device is ready to be setup and hit the
NEXT button.
18. Connecting to the POLYVISION
Step 4: Choose the PV device and follow directions below:
Adapter- PC Directions
Select and hit the next button
19. Connecting to the POLYVISION
Step 5: Select the Use Passkey found in documentation and type in the
passcode 1,2,3,4 and hit next.
Adapter- PC Directions
Passcode is 1, 2, 3,4
Hit next after entering code.
20. Connecting to the POLYVISION
Step 6: The computer will connect to the RM Classboard Bluetooth .
Adapter- PC Directions
21. Connecting to the POLYVISION
Adapter- PC Directions
Final Step: Your Bluetooth is now configured and ready to be used.
Click on the finish button.
22. Configuring the POLYVISION Driver-
PC Directions
Step 1: Click on the
Polyvision board
short cut and choose
the “Configure
Polyvision Driver tab.”
23. RM Classboard Configuration
Preferences- PC Directions
Short-cut to the board driver
can be found on the desktop to access
the configuration. Click to launch
configuration options.
Choose the “best” selection on the
“projection” tab. This will give you the
best calibration.
24. Connecting to the POLYVISION
Adapter to the Classboard
Bluetooth- PC Directions
Final step is to connect
the whiteboard by
clicking the “find serial
whiteboard button.”
Once the board is
connected you will hear
the board “chirp.”
Now hit the projector
button on the board
short cuts and this will
take you to the
calibration screen.
25. Connecting the POLYVISION Adapter to the
IWB Bluetooth- PC Directions
After you go through the previous steps one time, you
should automatically connect to the board as long as
your Polyvision Bluetooth Adapter is inserted in your
computer…every time you turn on the board, it will
automatically connect with the “chirp.”
Then you hit the projection button and the board is ready
to use.
26. Calibrating the PolyVision Boards
Hit the projection short cut button on the board this
green calibration screen will pop up. Hit each target to
ensure perfect calibration.