Davonne alunimium shutter manual 2015

1. ALUMINIUM SHUTTERS
 Material: 6063-T5
 Unique cast aluminium powder-coated end caps
 3 Blades Sizes:
63.5mm 115mm
 5 Standard Colours, 10 year finish Warranty:
-White Gloss
-White Satin (22% gloss)
- Birch White (22% gloss)
- Silver Pearl
- Black Matt
 3 Wood Grain Colours:
- Red Cedar
- Walnut
- Jarrah
 4 different types of Shutters
- Fixed Shutter
- Sliding Shutter
- Multifold
- Hinged Shutter
HINGED SHUTTER
WIDTH GUIDELINES FOR HINGED SHUTTER
3 frames are for options. RF L Frame, FF L Frame and Z Frame.
Hinged 400mm 900mm 900mm
 Panels over 1500mm in height require a mid-rail.
 Maximum Panel Height is 3000mm.
 Please consider transport and access when ordering large, tall and wide panels.
RF L FRAME Z FRAME FF L FRAME W/CAP
90mm
WIDTH
GUIDLINES
Minium per Panel Maximum
64mm Blades
Maximum 90mm &
125mm Blades

2.  Frames are supplied mitred with cast frame joiners. Assembled Frames or
Un-assembled Frames must be specified on order form.
 Default hinges are Aluminum Powder Coated Lift-off Hinges and Stainless Steel
Lift-off Hinges. Aluminum hinges are powder coated to match panels and factory fitted.
 Default catch is a white plastic Canoe Clip . Different sizes of canoe
clips are applied on different frames.
 D mould Stiles, with inserted black or white brush padding are available. Use a
“D” on the layout code to designate D mould stile panel.
Non D mould Stile (#4237652) D mould Stile (#4237651)
 Frames, T posts, hinges and gaps between are required to made deduction.
 T posts (#4237589) will be spaced between equal sized panels
unless position is nominated on order form.
 Only the minimum number of T Posts required to hinge the opening are covered
within the m2 rate. Additional T Posts are charged by the linear meter.
 Every hinged order will OPEN IN unless specify on order form.
-3mm each -2mm each
Width deductions
for each side
-3mm each -2mm each
Suitable for Out-
of-square
openings
Make deductions for any additional specified items such as brackets, angles, horizontal
posts etc. Any additional clearance required must be specified on order form.
Please ensure the smallest measurement takes squareness into account.
Drop deductions
for top and
bottom
Direct Hinged Hinged in RF L
Frame
Order as IM IM

3. Care & Maintenance
 Your YFA Shutters have been supplied with a protective tape over the stiles and
 Clean with a dilute solution of a mild liquid detergent in warm water.
 Use a soft bristle brush, soft cloth or similar. Do not use abrasives.
 Wipe or Rinse thoroughly with fresh water.
 When dry, apply lubricants:
 Do not use strong solvents on the coating. Do not use bore water for cleaning.
All organic finishes are prone to some degradation with prolonged exposure.
 63.5mm and 90mm are generally easy to operate with one hand centered within
 To ensure a good closure of the blades they must be shut firmly. The blades are
 When sliding the shutter panels past on other, please ensure all the blades are in
Stainless Steel, Locks
& Hinges
Top Tracks (with
trolleys or rollers)
Component
Blade Pins
rails. Please ensure this tape is removed prior to any exposure to sunlight or heat. The
tape
should not remain on the surface for any longer than 45 days after installation.
 The surface of your YFA Shutters must be kept clean, as dirt, grime and airborne salt
deposits from the atmosphere can damage the coating. For external applications we
recommend cleaning every three months and at least every six months. A shorter interval
may be necessary in marine or other corrosive environments.
Preventative
maintenance
Spray WD40 or similar marine grade lubricant on blade
pivots (at the end of the blade between the blade and the
stile). Wipe away excess with a soft dry cloth.
Clean, dry and spray with marine grade lubricant such as
CRC Marine 66, WD4o or Inox-Care
Apply Petroleum Jelly or WD40 to the inner lip of each side
of the track. Ensure that the wheels or trolleys pass through
the lubricant and it is distributed evenly along the track. Put
additional lubricant around the bearings.
After long service some change of colour, loss of gloss or chalking may be expected.
Stainless
the operation group of blades. However, for 115mm blade, please use 2 hands and
operate
from the middle of the group of blades (ie try to spread the load the operation of the
blade over more than one blade), not from the top or bottom blades, so as to take less
effort. The weight and span off these blades must be taken into consideration when
tensioned for normal wind areas and will not close in these conditions, however the
blades may
move in extremely windy conditions. We recommend you leave the blades in a closed
the closed position, if blades are open, the panels are slammed together this will be
considered
misuse.