What Are The Drone Anti-jamming Systems Technology?
ย
1 6
1. ISSN: 2277 โ 9043
International Journal of Advanced Research in Computer Science and Electronics Engineering
Volume 1, Issue 5, July 2012
Performance and Analysis of DS-CDMA Rake Receiver and Analyzing the
BER Performance in Presence of Nonlinear Distortion in DS-CDMA System
Y Mohan Reddy, K Manjunath, K Yogaprasad
๏ uses a set of unique signature sequence or spreading codes to
Abstractโ In this paper analysis the performance of a CDMA modulate the data bits of deferent users. With the knowledge
system by varying the system parameters. CDMA is a popular of these spreading codes, the receiver can isolate the data
technology in cellular system due to its superior capacity and corresponding to each user by the process of Channel
performance. In conventional CDMA, obtained better signal to estimation and detection. This process spreads the bandwidth
noise ratio by using matched filter because of this rake receiver of the underlying data signal; hence CDMA is called a spread
is used in CDMA to obtain desired signal to noise ratio. Rake
spectrum technique. Standards such as IS-95 and the
proposed W-CDMA are based on CDMA technology [4].
receiver is one of the receiver technique, consists of multiple
correlators, in which the receive signal is multiplied by DS-CDMA signals typically exhibit large dynamic range
time-shifted versions of a locally generated code sequence. To since they represent the sum of signals of many users.
maximize the Signal to Noise Ratio and minimize the Bit Error Unfortunately, when passed through a high power amplifier
Rate the CDMA Rake receiver is used. A predistorter-high
(HPA), this large dynamic range results in distortion for
power amplifier (PD-HPA) pair has become a common practice
in wireless communication to compensate for nonlinear components falling in the highly nonlinear regions of the
distortion due to HPA. However, the PD-HPA pair still HPA, which degrades the system bit error rate (BER) [12].
produces severe signal distortion when the input signal exceeds A common parameter for characterizing the dynamic range
the PD-HPAโs saturation level. The effects of such distortion on of a signal is the signal peak-to-average power ratio (PAR).
bit error rate (BER) degradation in direct sequence-code PAR is often used as an indicator to how much harm the
division multiple access signals (DS-CDMA) are analyzed. signal will suffer due to HPA nonlinearity, and also allows
Assuming that the baseband CDMA signal is characterized as a the system designer to determine the required amount of
complex Gaussian process, we develop analytic expressions for input back-off (IBO) to reduce nonlinear distortion effects.
the BER and the contributing factors to BER.
While PAR has its use, a signalโs dynamic range in relation to
an HPA only captures only one feature of the signalโs
Key Words:-CDMA (code Division Multiplexing), DS-SS
(Direct Sequence (DS) Spread Spectrum), FDMA (Frequency interplay with the HPA.
Division Multiplexing), PN (Pseudo Noise), SNR (signal to Noise We reformulate which signal characteristics to consider
Ratio), BER (Bit Error Rate), Nonlinear Distortion, beyond dynamic range that can be linked directly with BER.
Predistortion, HPA (High Power Amplifier). In the analysis, we assume that the nonlinear amplifier chain
includes a predistorter prior to the HPA, namely PDHPA.
I. INTRODUCTION The PD-HPA has a zero AM-PM characteristicโ ๐(๐ก) , and
Wireless cellular telephony has been growing at a faster rate an AM-AM characteristic given by
than wired-line telephone networks. The main factor driving ๐บ ๐ ๐ก = ๐ ๐ก 0โค ๐ ๐ก โค ๐ (1)
this tremendous growth in wireless coverage is that it does = ๐ ๐ ๐ก > ๐
not need the setting up of expensive infrastructure like copper Where๐(๐ก) is the input to the PD-HPA and ๐ is the PD-HPA
or fiber lines and switching equipment. This growth has also saturation (clipping) threshold. Assuming that the baseband
been fueled by the recent improvements in the capacity of
wireless links due to the use of multiple access techniques CDMA signal is characterized as a band-limited complex
(which allow many users to share the same channel for Gaussian process, we establish analytical expressions for the
transmission) in association with advanced signal processing signal characteristics, with respect to the IBO level, that lead
algorithms. Code Division Multiple Access (CDMA) is to BER degradation. Moreover, we develop an analytic
becoming a popular technology for cellular communications expression for the BER performance in presence of the
[1].
considered nonlinear amplifier chain.
Unlike other multiple access techniques such as
Frequency Division Multiple Access (FDMA) and II. RAKE RECEIVER
Time-Division Multiple Access (TDMA) [7], which are
limited in frequency band and time duration respectively,
CDMA uses all of the available time-frequency space. One In a mobile radio channel reflected waves arrive with
form of CDMA called Direct Sequence CDMA (DS-CDMA) small relative time delays, self interference occur. Direct
Sequence (DS) Spread Spectrum is often claimed to have
Manuscript received June 15, 2012. particular properties that makes it less vulnerable to
Y Mohan Reddy, student,, dept of ECE, SITAMS, Chittoor, Andhra multipath reception. In particular, the rake receiver
Pradesh, India,+91-9014157437(mohanreddy.404@gmail.com). architecture allows an optimal combining of energy received
K Manjunath, Assistant Professor department of ECE, over paths with different [6]. It avoids wave cancellation
SITAMS, Chittoor, Andhra Pradesh, India, +91-9052232027 (fades).If delayed paths arrive with phase differences and
(manjunathak83@gmail.com). appropriately weighs signals coming in with different
K Yogaprasad, Associate Professor, Dept of ECE, SITAMS,
Chittoor, AndhraPradesh India,+919908085522
signal-to-noise ratios [2].
(kyogaprasad@gmail.com).
1
All Rights Reserved ยฉ 2012 IJARCSEE
2. ISSN: 2277 โ 9043
International Journal of Advanced Research in Computer Science and Electronics Engineering
Volume 1, Issue 5, July 2012
The rake receiver [3, 6] consists of multiple correlators, According to the maximum ratio combining principle, the
in which the receive signal is multiplied by time-shifted SNR at the output is the sum of the SNRs in the individual
versions of a locally generated code sequence. The intention branches, provided that,
is to separate signals such that each finger only sees signals 1. We assume that only AWGN is present (no interference).
coming in over a single (resolvable) path. The spreading code 2. Codes with a time offset are truly orthogonal.
is chosen to have a very small autocorrelation value for any Signals arriving with the same excess propagation delay as
nonzero time offset. This avoids crosstalk between fingers. In the time offset in the receiver are retrieved accurately,
practice, the situation is less ideal. It is not the full periodic because
autocorrelation that determines the crosstalk between signals
in different fingers, but rather two partial correlations with ๐ ๐
2
contributions from two consecutive bits or symbols. It has ๐1 ๐๐ ๐ + ๐ก ๐ = ๐1 2 ๐๐ ๐ = ๐ (2)
been attempted to find sequences that have satisfactory ๐=1 ๐=1
partial correlation values, but the crosstalk due to partial This reception concept is repeated for every delayed path that
(non-periodic) correlations remains substantially more is received with relevant power. Considering a single
difficult to reduce than the effects of periodic correlations the correlator branch, multipath self-interference from other
rake receiver is designed to optimally detect a DS-CDMA paths is attenuated here, because one can choose codes such
signal transmitted over a dispersive multipath channel. It is that [4].
an extension of the concept of the matched filter [2, 9].
๐
๐1 ๐๐ ๐ ๐1 ๐๐ ๐ + ๐ก ๐ โ 0 (3)
๐=1
III. MULTIPATH AND RAKE RECEIVER
One of the main advantages of CDMA systems is the
capability of using signals that arrive in the receivers with
different time delays. This phenomenon is called multipath.
Fig 1: Matched Filter Receiver for AWGN Channel FDMA and TDMA, which are narrow band systems, cannot
discriminate between the multipath arrivals, and resort to
In the matched filter receiver, the signal is correlated equalization to mitigate the negative effects of multipath [5,
with a locally generated copy of the signal waveform. If, 10]. Due to its wide bandwidth and rake receivers, CDMA
however, the signal is distorted by the channel, the receiver uses the multipath signals and combines them to make an
should correlate the incoming signal by a copy of the even stronger signal at the receivers. CDMA subscriber units
expected received signal, rather than by a copy of transmitted use rake receivers. This is essentially a set of several
waveform. Thus the receiver should estimate the delay receivers. One of the receivers (fingers) constantly searches
profile of channel, and adapt its locally generated copy for different multipath and feeds the information to the other
according to this estimate [2, 7]. three fingers. Each finger then demodulates the signal
In a multipath channel, delayed reflections interfere corresponding to a strong multipath. The results are then
with the direct signal. However, a DS-CDMA signal combined together to make the signal stronger [2].
suffering from multipath dispersion can be detected by a rake
receiver. This receiver optimally combines signals received Multipath Reception
over multiple Paths.
Experiments with mobile communication were done at
VHF frequencies, near 50 MHz, already in the 1920s. Results
of these tests revealed a very hostile propagation
environment, particularly in urban centers. The signal quality
varied from "excellent" to "no signal". Moving the vehicle
over a few meters resulted in dramatic changes of the
received field strength [11].
Fig 2: Rake Receiver with 5 Fingers
Like a garden rake, the rake receiver gathers the energy
received over the various delayed propagation paths.
2
All Rights Reserved ยฉ 2012 IJARCSEE
3. ISSN: 2277 โ 9043
International Journal of Advanced Research in Computer Science and Electronics Engineering
Volume 1, Issue 5, July 2012
๐ โ
โ๐ 2
Fig 3: Bit Error in Multipath Fading = ๐ 2 ๐๐ ๐ ๐๐ + ๐ 2 ๐๐ ๐ ๐๐ = 2๐ 2 1 โ
2 (10)
๐ฅ
0 ๐ ๐ 2๐ ๐ฅ
IV. CDMA SYSTEM PERFORMANCE Evaluating the BER in the case of an optimum receiver is
difficult and tedious; hence, the BER for a suboptimum
The system under investigation is a downlink CDMA receiver is used as an upper bound [13]. We adopt the
system in which the usersโ signals are synchronized and have decorrelating receiver, where multi-user interference is
equal power. The complex envelope of the CDMA signal for eliminated [13], [15] at the expense of noise enhancing. For
K active users is defined as [12], [13]
the decorrelating receiver, the ๐พ ๐กโ user BER is given by
๐พ โ ๐ฟโ1 ๐ต๐ธ๐ ๐พ = ๐ ๐๐๐ ๐ (11)
๐ ๐ก = ๐ธ๐ ๐ ๐ ๐ ๐ ๐ก ๐ โ ๐ก โ ๐๐๐ โ ๐๐ Where๐๐๐ ๐ is the signal-to-noise ratio at the ๐พ ๐กโ receiver
โ๐ข 2
๐=1 ๐=โโ ๐=0 โ ๐ 2
= ๐ฅ ๐ก + ๐โ ๐ฆ ๐ก = ๐ (4) and ๐ ๐ = ๐ฅ โ2๐
๐๐ข .Including Additive White Gaussian
Where ๐ธ ๐พ is the ๐พ ๐กโ userโs signal energy per bit, T is the Noise (AWGN), ๐๐๐ ๐ is given by [13, eq. (15.3-65, 67)]
symbol duration, L is the spreading factor,๐๐ = ๐ ๐ฟ is the ๐2 ๐ ,๐ ๐ธ๐
(๐) ๐๐๐ ๐ = ๐๐๐ ๐ด๐๐บ๐ ,๐ = 2 = (12)
chip duration, ๐ถ ๐ is the ๐ ๐กโ chip in the spreading code ๐ ๐,๐ ๐ ๐ ๐2๐
๐
๐ถ ๐ = ๐ถ0 ๐ โฆ โฆ โฆ โฆ . . ๐ถ ๐ฟโ1 , h(t) is the impulse response
๐ Where ๐๐๐ ๐ด๐๐บ๐ is the SNR due to AWGN only, ๐ 2 is the ๐
(๐) variance of the AWGN and ๐ ๐ = ๐ โ1 ๐,๐ is the noise
๐
of the transmit pulse shaping filter, and ๐ ๐ = (ยฑ1 ยฑ ๐)/โ2
enhancement factor introduced by the decorrelating receiver
is the๐พ ๐กโ userโs symbol data for QPSK modulation in the ๐ ๐กโ
[13], where Rs is the correlation matrix with elements๐ ๐๐ 0
symbol duration. Moreover, the symbols ๐ ๐ ๐ are assumed to ๐
(๐) 2 defined as๐ ๐๐ 0 = ๐ ๐ ๐ ๐ .
be independent with zero mean and variance of ๐ธ ๐๐ In the presence of a nonlinear amplifier, the SNR measured at
[12]. the ๐พ ๐กโ receiver input is the ratio of the transmitted distorted
For a large number of users and assuming the pulse signal power ๐ 2 = ๐0 2 ๐ 2 + ๐ 2 to the noise power ๐ 2
๐ ๐ ๐๐ ๐,๐
shaping filter corresponds to a square-root raised cosine filter โ๐ 2
(SRRC) with small roll-off factor, x (๐ก) and ๐ฆ(๐ก) can be ๐2๐,๐ ๐ 2 (1
๐ ,๐ โ
2
๐ 2๐ ๐ฅ )
regarded as two uncorrelated zero-mean Gaussian processes ๐๐๐ ๐ = =
๐ ๐ ๐2๐ ๐ ๐ ๐2
๐
with equal variances, that is ๐ 2 =๐ 2 [14]. Hence, ๐ (๐ก)can be
๐ฅ ๐ฆ โ๐ 2
regarded as a complex zero-mean Gaussian process with a = ๐๐๐ ๐ด๐๐บ๐ ,๐ 1 โ ๐ 2๐ 2
๐ฅ (13)
variance of
๐พ Actually, once the PD-HPA is designed, its saturation
2
๐2
๐ = 2๐ 2
๐ฅ = ๐ธ ๐ ๐ธ{ ๐ ๐ ๐ } = ๐พ๐ธ ๐ (5) threshold is fixed. However, the clipping threshold with
๐=1 respect to the input signal to the PD-HPA depends on the
Since ๐ถ ๐ ๐ = 1. The envelope ๐ ๐ก = ๐ฅ 2 ๐ก) + +๐ฆ 2 (๐ก signal average power. Therefore, it is more convenient to
has a quasi- Rayleigh distribution [14], with probability relate the threshold ๐ to IBO, where the IBO is the ratio of the
density function [13]. input power at the PD-HPA saturation threshold to the signal
๐ ๐2 average power. This relation allows the system operator to
๐๐ ๐ = 2 ๐ โ 2 ๐โฅ0 (6) determine the optimum IBO required, according to the design
๐๐ฅ 2๐ ๐ฅ demands. Hence, the threshold level can be defined thru the
Finally, the output from the PD-HPA can be expressed as IBO,๐พ, multiplied by the signal average power๐๐๐ฃ , that is
๐ ๐ ๐ก = ๐ ๐ ๐ก ๐ ๐ ๐ ๐ ๐ก = ๐บ ๐ ๐ก ๐ ๐๐ ๐ก (7)
๐ = ๐๐๐ฃ โ ๐พ = ๐ 2 โ ๐พ
๐ (14)
โ๐ 2
V. BER PERFORMANCE ANALYSIS The term ๐ 2๐ 2
๐ฅ
in (13) represents the probability that the
Using the Bussgang theorem extension for a complex signal envelope exceeds the threshold ๐ , equivalently the
Gaussian input to a memory less nonlinear device, the output threshold exceeding rate RE, which using (14) is written as
of the PD-HPA can be represented as the sum of two โ๐ 2
2
uncorrelated components: a scaled linear component and a ๐ ๐ธ = = ๐ โ๐พ ๐ 2๐ ๐ฅ (15)
nonlinear component,๐ ๐๐ ๐ก , [12], [14], [15], that is Substituting (15) in (13) and then in (11), the BER in
๐ ๐ ๐ก =โ ๐ ๐ ๐ก + ๐ ๐๐ ๐ก (8) presence of the PD-HPA as a function of the IBO level has
Where ๐ธ ๐ ๐ก ๐ โ ๐ก = 0and โ ๐ is the linear gain given by
๐๐ the form
๐ธ ๐ ๐ก ๐ โ ๐ก
๐๐ ๐ธ ๐บ ๐ ๐
โ ๐= = (9) ๐ต๐ธ๐ ๐ = ๐ ๐๐๐ ๐ด๐๐บ๐ ,๐ 1 โ ๐ ๐ธ (16)
๐ธ ๐ ๐ก 2 2๐ 2
๐ฅ
Consequently, the variance of the distorted signal ๐ ๐ ๐ก is From (16), it is clear that the threshold exceeding rate๐ ๐ธ is
given by ๐ 2 = ๐0 2 ๐ 2 + ๐ 2 where ๐ 2 is the variance of the
๐ ๐ ๐๐ ๐๐
the main contributor to BER degradation; by minimizing๐ ๐ธ ,
nonlinear component๐ ๐๐ ๐ก . As far as ๐ (๐ก)is considered as a ๐๐๐ ๐ ๐s maximized resulting in BER improvement, and vice
zero-mean complex Gaussian process, ๐ 2 can be calculated
๐
versa. This result can be understood from the PD-HPA
as transfer function. When the input signal exceeds the
โ saturation threshold ๐ , an output signal value has a
๐ 2 = ๐ธ ๐ ๐ (๐ก)
๐
2
= ๐ธ ๐ 2 (๐ก) =
๐ ๐ 2 ๐๐ (๐)๐๐
๐ many-to-one mapping to the input values, where,
0
discriminating between these input values at the receiver to
recover the original transmitted data would be challenging,
3
All Rights Reserved ยฉ 2012 IJARCSEE
4. ISSN: 2277 โ 9043
International Journal of Advanced Research in Computer Science and Electronics Engineering
Volume 1, Issue 5, July 2012
resulting in expected BER degradation. Effectively, errors
are introduced in advance at the transmitter.
Actually,๐ ๐ธ is not the only contributor to BER degradation
since the BER in (16) is based on the SNR in (12). Such SNR
is the apparent SNR since an increase in the nonlinear
component variance ๐ 2 ,๐ as part of ๐ 2 in (11) increases the
๐๐ ๐,๐ Fig.4. (b) Output envelope ๐ ๐ ๐ก from PD-HPA.
SNR, although effectively deteriorates the BER [15], [16].
While the effective SNR, where the non-linear signal ๐ ๐๐ ๐ก
in (8) is assumed Gaussian distributed [12], is defined as [15]
๐ผ0 2
๐2
๐ ,๐ ๐ผ0 2 ๐ 2
๐ ,๐
๐๐๐ ๐๐๐ ,๐ = = 2
๐2
๐,๐ + ๐ 2 ,๐
๐๐ ๐ ๐,๐ + ๐ 2 โ ๐ผ0
๐,๐
2 ๐2
๐ ,๐ Fig.4. (c) clipped envelope portion๐๐ ๐ก .
๐ผ0 2 ๐ 2
๐ ,๐ Rearranging (22) and substituting into (19), ๐ผ ๐ is given by
= (17) 1 1 1 1
๐ 2 + ๐ 2 (1 โ ๐ ๐ธ โ ๐ผ0 2 )
๐,๐ ๐ ,๐ ๐ผ ๐ = 1 โ โ๐พ โ 2 ๐ 2 = 1 โ โ 2 ๐2 (23)
๐
Substituting (17) in (11), the BER in presence of the 2๐ 4๐ ๐ฅ 2๐ ๐ธ 4๐ ๐ฅ ๐
PD-HPA, according to๐๐๐ ๐๐๐ ,๐ , has the form From (23) as part of (16), it is clear that ๐ ๐ธ and ๐ 2 are the
๐
main contributors to the BER performance; decreasing๐ ๐ธ
๐ผ0 2 and๐ 2 , increases๐ผ0 , increases๐๐๐ ๐ , and in turn improves
๐
๐ต๐ธ๐ ๐ = ๐ 2
(18)
1 โ ๐ ๐ธ โ ๐ผ0 + (๐๐๐ ๐ด๐๐บ๐ ,๐ )โ1 BER.
Looking to the linear gain ๐ผ0 , it can be expanded as VI. ALGORITHM AND IMPLEMENTATION
โ
1
๐ผ0 = 2 ๐ ๐ ๐ ๐ ๐๐
2๐ ๐ฅ 0 ๐ ๐
๐ โ
In this section, discussing about the MATLAB algorithm
1
= 2 ๐ 2 ๐๐ ๐ ๐๐ + ๐ ๐๐๐ ๐ ๐๐ and implementation techniques
2๐ ๐ฅ 0 ๐ i. Generate a fifteen bit user data for each user to simulate
๐2 with Rake or without Rake on MATLAB.
โ 2
2๐ ๐ฅ
1 ๐๐ 2 ๐
=1โ ๐ + ๐๐๐๐ ii. Generate a PN sequence data for every user.
2 2๐ 2
๐ฅ 2๐ 2
๐ฅ iii. Generate code data by multiplication of user data and PN
โ ๐๐พ sequence.
= 1โ ๐ ๐ธ + ๐๐๐๐ ๐พ (19) iv. Add AWGN noise with the code and we create multiple
2
The output of the PD-HPA can be written as path with different attenuation, every multipath add
๐ ๐ ๐ก = ๐ ๐ ๐ก ๐ ๐๐ ๐ก = ๐ ๐ก โ ๐๐ ๐ก ๐ ๐๐ ๐ก random noise to code so at the end of path we will get
= ๐ ๐ก โ ๐ ๐ ๐ก (20) multiple code with different noise.
v. Comparing the BER performance of WITH and
Where๐ ๐ ๐ก = ๐๐ ๐ก ๐ ๐๐ ๐ก is the signal portion that is clipped
WITHOUT Rake receiver for different attenuation factors.
from๐(๐ก),๐ธ ๐ ๐ (๐ก) = 0, and its envelope๐๐ (๐ก) has the form
๐๐ ๐ก = ๐ ๐ก โ ๐ ๐ ๐ก
VII. SIMULATION RESULTS
= 0, ๐ ๐ก โค ๐
= ๐ ๐ก โ ๐, ๐ ๐ก > ๐ (21) Here we are observing the performance of CDMA system
Examples of ๐ ๐ก ,๐ ๐ ๐ก , and ๐๐ ๐ก are shown in Fig. 4(a), Fig. with and without rake receiver. Figure 5 shows that the
4(b), and Fig. 4(c), respectively. performance of CDMA system with and without rake
The variance ๐ 2 of ๐ ๐ ๐ก can be derived using the
๐
receiver for different attenuation factors to minimize the Bit
definition of the envelope of the clipped signal portion in (21) Error Rate.
performance analysis of with and without rake receiver
as 0
10
โ with rake
๐2 = ๐ธ
๐ ๐๐ ๐ก 2
= ๐ธ ๐๐2 ๐ก = ๐โ ๐ 2
๐๐ ๐ ๐๐ without rake
-1
๐ 10
๐2
2
โ 2 ๐
= 2๐ ๐ฅ ๐ 2๐ ๐ฅ โ 2๐๐ 2 ๐๐๐๐๐
๐ฅ
...................BER
-2
2๐ 2
10
๐ฅ
= 2๐ 2 (๐ โ๐ฆ โ
๐ฅ ๐๐พ ๐๐๐๐ ๐พ (22) -3
10
-4
10
-5
10
0 5 10 15 20 25 30 35
..................EbNo
Fig 5: Performance of CDMA system with and without rake receiver.
Fig.4. (a) Input envelope ๐ ๐ก to PD-HPA.
Figure 6 shows that performance of multipath using rake
receiver in CDMA system and figure 7 shows that BER
performance for conventional CDMA and proposed RAKE
Receiver.
4
All Rights Reserved ยฉ 2012 IJARCSEE
5. ISSN: 2277 โ 9043
International Journal of Advanced Research in Computer Science and Electronics Engineering
Volume 1, Issue 5, July 2012
To assess the validity of the derived expressions for the
factors contributing to BER degradation, ๐ ๐ธ and ๐ 2 , and the
๐
linear gain ๐ผ0 , a 64-user CDMA signal filtered using an
SRRC filter with Walsh codes of length L = 64 is simulated.
๐ ๐ธ ,๐ 2 , and ๐ผ0 are measured for the simulated signal and
๐
compared against the analytic expressions in (15), (22), and
(23), respectively. The relations of such factors versus IBO
are shown in Fig. 8, where the agreement between the
analytic curves and simulated points confirms the analytic
derivations.
Finally, the analytically derived BER is computed from
(16) and compared against the BER measured from
simulation. Fig. 9 shows the BER curves, where it is evident
Fig.9 Analytic and simulated plots of BER at different IBO levels.
that good agreement exists between the analytic curves and
the measured points for all IBO levels.
0
Multiple paths of rake receiver CONCLUSION
10
1-path
2-path
3-path
In this paper, Rake receiver is used for CDMA
4-path technique rather than using conventional CDMA with
-1
10
matched filter. Rake receiver is used to minimize the bit error
rate and obtain maximum signal to noise ratio.
-------BER
In this how nonlinear distortion due to PD-HPA affects BER
degradation for transmitted DS-CDMA signals. We
-2
10 established analytically how the threshold exceeding rate ๐ ๐ธ
and the variance of the clipped portion of the signal ๐ 2 . ๐
contribute to BER degradation. The motivation of this work
-3
is to provide system designers/operators with efficient tools
10
2 3 4 5 6 7 8
--------Ebno(dB)
9 10 11 12 that provide potential insight into the interactions between
CDMA signals and the nonlinear PD-HPA, leading to better
Fig 6: performance of multipath using rake receiver in CDMA system.
understanding of the impact of the PD-HPA on system BER.
Moreover, establishing these characteristics for the input
Performance analysis of the with and without rake receivers
10
0
signal in relation to the PD-HPA characteristics opens new
Coventional
Proposed
avenues for research to minimize the effect of nonlinear
distortion before the signal even hits the amplifier. For
-1
10 instance, in search and optimization techniques such as the
selected mapping technique, where many representations of
the same signal are generated and the one that achieves the
------BER
-2
10
minimum of these characteristics is selected for transmission.
10
-3
REFERENCES
[1] Peter Flanagan, โPersonal Communications Services: The Long
-4
Road Ahead,โ Telecommunications, February 1996.
10
2 4 6 8 10 12 14 16 18 20 [2].http://wireless.per.nl/reference/chaptr05/cdma/rake.htm.
------Ebno (dB)
[3] W. C. Y. Lee, โOverview of Cellular CDMA,โIEEE Trans. On
Fig 7: BER graph for conventional and proposed systems Vehicular Technology, Vol. 40, no. 2, pp. 291-302, May 1991.
[4] R. A. Cameron and B. D. Woerner, โAn Analysis of CDMA with
Imperfect Power Control,โ Proceedings of 42nd IEEE Vehicular
Technology Conference, Denver, CO, pp. 977-980, 1992.
[5] R. Lupas and S. Verdu, โLinear Multiuser Detectors for
Synchronous Code Division-Multiple-Access Channels,โ IEEE
Trans. Info. Theory, vol. 35, no.1, pp. 123-136, Jan. 1989.
[6]. K.Murali.Krishna, Abhijit Mitra and Cemal Ardilโ A Simplified
Single Correlator Rake, Receiver for DMA Communicationsโ
International Journal of Information Technology Volume 2
Number 4 2005.
[7] P. Jung, P. W. Baier, and A. Steil, โAdvantages of CDMA and
Spread Spectrum Over FDMA and TDMA in Cellular Mobile
Radio Applications,โ IEEE Transactions Vehicular Technology,
Vol. 42, no. 3, pp. 357- 364, August 1993
[8] Electronic Industries Association, โCellular System Dual-Mode
Mobile Station Base Station Compatibility Standard,โ IS-54,
May 1990.
Fig.8. Analytic and simulated plots of๐ ๐ธ , ๐ 2 , and ๐ผ ๐ over a range of IBOs.
๐
5
All Rights Reserved ยฉ 2012 IJARCSEE
6. ISSN: 2277 โ 9043
International Journal of Advanced Research in Computer Science and Electronics Engineering
Volume 1, Issue 5, July 2012
[9] K. S. Gilhousen, โOn the Capacity of a Cellular CDMA
System,โIEEE Transactions on Vehicular Technology, Vol. 40,
no. 2, pp. 303-311,May 1991.
[10] Electronic Industries Association, โWideband Spread Spectrum
Digital Cellular System Dual Mode Mobile Station - Base
Station Compatibility Standard,โ IS-95, April, 1992.
[11] J. C. Liberti and T. S. Rappaport, โAnalytical Results for
Capacity Improvements in CDMA,โ IEEE Transactions on
Vehicular Technology, Vol.43, No. 3, pp. 680-690, August
1994.
[12] A. Conti, D. Dardari, and V. Tralli, โAn analytical framework
for CDMA systems with a nonlinear amplifier and AWGN,โ
IEEE Trans. Commun.vol. 50, no. 7, pp. 1110โ1120, July 2002.
[13] J. Proakis, Digital Communications, 4th ed. McGraw-Hill,
2000.
[14] R. Dinis and A. Palhau, โA class of signal-processing schemes
for reducing the envelope fluctuations of CDMA signals,โ IEEE
Trans. Commun., vol. 53, no. 5, pp. 882โ889, May 2005.
[15] L. Rugini, P. Banelli, and S. Cacopardi, โTheoretical analysis
and performance of the decorrelating detector for DS-CDMA
signals in nonlinear channels,โ IEEE Trans. Wireless Commun.,
vol. 3, no. 2, pp. 367โ372, Mar. 2004.
[16]P. Banelli and S. Cacopardi, โTheoretical analysis and
performance of OFDM signals in nonlinear AWGN channels,โ
IEEE Trans. Commun., vol. 48, no. 3, pp. 430โ441, Mar. 2000
ABOUT THE AUTHORS
Mr. Y MOHAN REDDY received B.Tech degree from
JNT University, Anantapur and is pursuing his
M.Tech degree from JNT University, Anantapur. He
presented 2 technical papers in various national level
conferences. His area of interest is wireless
communication.
Mr.K.MANJUNATH working as Assistant Professor
in the department of ECE in SITAMS, chittoor. He
received B.Tech degree from Anna University,
Chennai and M.Tech degree from VIT University,
Vellore. He presented 2 technical papers in various
national level conferences. His areas of interest is
digital image processing and wireless networks.
Mr.K.YOGAPRASAD working as Associate Professor
in the department of EIE in SITAMS, chittoor. He
received B.Tech degree from madras university,
Chennai, M.Tech degree from vishweswaraiah
university, Belgaum. and pursuing Ph.D from JNT
university, Anantapur. He presented 3 technical papers
in various national level conferences . His areas of
interest is wireless communication networks.
6
All Rights Reserved ยฉ 2012 IJARCSEE