Ic 555 timer types and applications

1. *
By
-Abhijit H/ adl1av (Roll no 02)
-(Roll no 58)

2. y•
e
0 Introduction
0 Pin Configuration
0 Purpose of pin
O 555 Integral circuit
0 Opera ting modes
. / Bistable
. / Monostable
. / Astable
0 Application
0 Conclusion
0 Biblography

3. *
•• The SSS ICwas designed tin 1971
by Hans Camenzind under
contract to SigNetics
Corpora tion.
•• 555 tim er is a h ighly stabl
e
circuit used to generate
time
delays, or Oscilla tions.
•• A single SSS timer can
provid e tin1e delay ra nging from
microseconds to l1ours.
•• I t opera tes from a wide ra
nge
of power supplies ra ngi ng from +
5 Volts to + 18 Volts supply

4. Co
•Pin- 1: Ground
• Pin- 2: Trigger
• Pin- 3: Output
•Pin-4: Re et GND •
• Pin- 5: Control V
oltage TRIG
• Pin-6: Threshold
•Pin- 7: Discharge
•Pin- 8: Yee
•
g
ou
·
r
I 'Lf
555
DI
·
r1lR
CTRL

5. Pin noName Purpose
1 GN D Grou nd reference voltage, low level (0 V)
2 TRIG The OUT pin goes high and a lim ing interval starts when this
input falls below Y.z of CTRL voltage.
3 OUT Driven approx. 1.7 V below Vee or GN D
4 RESE
T
A tin1ing in terval may be reset by driving th is input to GN D.
5 CTRL Provides "control" access to the internal voltage divider (by
default 2/3 Vee) at THR is greater than that at CTRL
6 TllR The tim ing interval ends when the voltage at Tll R is greater
than that at CTRL
7 DIS Open collector output which may dishcha rge the capacitor
benveen interval in phase with output.
8 Vee Positive supply voltage, which is usually between 3 and 15 V
depending on the va ria tion.

6. *sssc•

7. *one
•
g
./ IC 555 has three operating modes:
1. mode or • 111+ t-. ,,, • - the SSS can operate as a
, i f the DIS pin is not connected and no capacitor is used. Uses incl
ude bounce-free latched switches.
mode - in this mode, the SSS functi ons as a "one-shot" pulse
generator. Applica tions incl ude timers, missing pulse detection, bou
nce-free switches, touch
switches, frequen cy divider, capacitance measuremen t,
(PWM) and so on.
(free-running) mode - the SSS can operate as an
2.
3.
I
r t
• Uses include and lamp flashers,
pulse generation, logic clocks, tone generation, security
alarms, and so on.

8. , In bistable (also called
the SSS tin1er acts as a basic flip-flop.
) mode,
,The trigge r and reset inputs (pins 2 and 4
respectively on a 555) are held high via
whtle the th reshold in pu t (pin 6) is simply
floating.
,Th us configured, pu lling the trigger
momen tarily to ground acts as a 'set' and
tra nsitions the outpu t pin (pin 3) to Vee (high
state).
-,. Pulling the reset: input to ground acts as a 'reset'
and transitions the outpu t pin to ground (low
state). No timing capaci tors
,Pi n 5 (control voltage) is con nected to ground via a
small-va lue capacitor (usua lly 0.01 to 0.1µF).
Pin 7 (d ischarge) is left floa ting
v
-
. .. a
RES
E
T v
2
TRIG
--
Tngge
r
6
THR
DIS
GNO CTRL
OUT
3 -
-
-
7
OUt
l s
lOn
f
GNO =
I

9. • Pulse generator circuit which the period is calculated from RC network
and connected to external of SSS timer
•Stable when the output logic LOW (logic = 0)
•When a pulse is trigger at pin 2 (normally negative trigger pulse), timer
outpu t wi ll change to H I GH (+Vs) for a wh ile and change to LOW (stable
condition). The condition willcontinue LOW until pulse is trigger again.
•The timing period is triggered (sta rted) when trigger input (SSS p in 2) is
less than 1/ 3 Vs, th is makes the output h igh (+Vs) and the capacitor Cl
starts to charge through resistor Rl. Once the time period has started further
trigger pulses are ignored.
•The threshold inpu t (SSS pi n 6) monitors the voltage across Cl and when
this reaches 2/3 Vs the time period over and the output becomes LOW,
•At the same tin1e discharge (SSS pi n 7) is connected to OV, dischargi ng the
capacitor ready for the next trigge r.

10. - - - - -
-
4+vcc
8
R
-
input trigger
r 1/3 Vee
- - - - - - - - - , Discharge
tra nsi tor
I I
:3
I
S Q Inverter 1
- - - - +
- - - - - - - - - -'
-
7•
I
6•
I
I
I
I
21
I
One-shot operation
-
-
1
R
-
I
I
I
The inpu t trigger resets the flip-flop an d C then charges u ntil
the u pper compa rator trip and cts the flip-flop.

11. *
0utpo1
n-
n-
.n_
Ra 6 SSS t -
3
2 ,
s
./ Astable multivibrators are also
known as Free
running Multivibrator.
./ Astable do not 11eed n-igge r
pulse for external to change
the output.
./ The period for LOW and
H IGH can be calculated based
on resistor and capacitor
value that
connected at outside of timer.
+V
a:
::::- 0.01µP
1
1
-
-
C charge through R + R8
and di charge through R8•

12. *
. /
. /
. /
. /
. /
. /
. /
. /
. /
Schmitt trigger PPM
PWM
linear Ramp genera tor
Precision Timing
Pulse Generation
Time Delay Generation
Sequential Timing
Used as a quad timer

13. c us•
0
Hence 555 IC timer can prod uce very accurate
and stable time delays,from microseconds to hours. It
can be used with supply voltage varying from 5
to 18 V. Tirner can be used in monostable mode of
operation or astable mode of
operation. I ts various applications include waveform
generator, missing pulse detector, frequency divider,
pulse width modulator, burg lar alarm,
FSK generator, ramp generator, pulse position
modulator etc.