Webinar Description:
Renewable Energy is important for many reasons. To remain viable as an alternative energy source these technologies must run reliably and at the lowest possible cost. Lubricated machines such as turbines and gearboxes require proper oil care and management. In this informative webinar led by C.C. Jensen's Justin Stover, you will learn practical steps that will make Renewable Energy greener; by conserving precious resources and slashing O&M costs.
Instructor: Justin Stover, C.C. Jensen, Inc.
Justin Stover earned his degree in 2001 in fluid power technology. He has more than 10 years experience in helping end users and OEM's in the Wind industry implement, develop and deploy contamination control programs. He is certified by the International Council for Machinery Lubrication as a Level 1 Machinery Lubricant Analyst.
For more information on reducing operating costs and increasing uptime in your equipment visit www.ccjensen.com and www.testoil.com.
Repurposing LNG terminals for Hydrogen Ammonia: Feasibility and Cost Saving
Making renewable energy greener with oil analysis and contamination control
1. Making Renewable Energy
GREENER with Oil Analysis and
Contamination Control
I.
The Importance of Analysis and Filtration
II.
Case Studies
III. Questions and Answers
2. The Importance of Analysis and Filtration
Renewable Energy is Important
to C.C.JENSEN
Our Wind Turbine
covers 40 % of our
energy consumption
3. The Importance of Analysis and Filtration
Renewable Energy is Important
for Many Reasons…
it’s Clean, Available, and Provides Security.
4. The Importance of Analysis and Filtration
WIND TURBINES – Pushing the Design Envelope
2 million N-m
(1,475,000 lb-ft)
Extreme pressure
on components
BLADES
120 m
(394 ft)
5. The Importance of Analysis and Filtration
CLEAN OIL
GEARBOX
PITCH
HYDRAULIC
Extreme pressure
BLADES
120 m
(394 ft)
on components
MAIN BEARING
GETS MORE AND MORE IMPORTANT
6. The Importance of Analysis and Filtration
THE IMPORTANCE OF CLEAN OIL AND IT’S IMPACT ON
RELIABILITY HAS BEEN KNOWN FOR DECADES
“Replacing 40-25µm filters by units rated at 3µm absolute is to
be recommended for gearboxes. Such action should lead to
improved reliability, longer periods between overhaul, cheaper
overhauls, and consequent reductions in ownership costs.
Times between oil changes, where relevant, should be
substantially increased.”
1979
The Influence of Filtration on Rolling Element Bearing Life
Source:
R. Bhachu, R. Sayles, and P.B. Macpherson
7. The Importance of Analysis and Filtration
Did You Know?
The estimated
gearbox failure in
a Wind Turbine is
estimated at
$250,000!
Ref: NORIA
8. The Importance of Analysis and Filtration
“Bearings Don’t Fail… They’re Murdered”
Ref: NORIA
9. The Importance of Analysis and Filtration
Did You Know?
The estimated cost of an
oil change is $5,000 on a
Wind Turbine.
LESS USE
OF FOSSIL OIL
LESS TRANSPORTATION
LESS WASTE OIL
IMPROVED FILTRATION
IS ABLE TO KEEP THE OIL CLEAN
AND MAKE IT LAST LONGER
10. The Importance of Analysis and Filtration
Every Barrel Counts…
16,000 Wind Turbines
X
100 Gallons
=
29,090 Barrels
Three-Year or Six-Year Oil Service Life – Which is GREENER?
11. The Importance of Analysis and Filtration
Oil Analysis Reduces Maintenance and Downtime!
PARTICLES
WATER
OXIDATION
12. The Importance of Analysis and Filtration
End of Section I
Take Away: No machine has ever failed because
the oil was too clean; What get’s measured
get’s done.
Question: What is the most important
parameter on your oil analysis test slate?
17. Case Study – Wind Power
“The oil at [our project] is the exact opposite of
the [clean] oil, its beyond filthy!! We should
have taken out disaster insurance on it…you
would not believe or want to see what comes
out of one of these when you turn it upside
down. Well, maybe you would. It was the most
disgusting, revolting lumpy stinky slime I’ve ever
seen come from the bowels of the gearbox.”
26. Case Studies
End of Section II
Take Away: Identify oil problems and take
action to correct; Monitor the oil to ensure
progress is made.
Question: What type of contamination do you
most often see?