A power plant is an industrial facility that generates electricity from primary energy. Most power plants use one or more generators that convert mechanical energy into electrical energy in order to supply power to the electrical grid for society's electrical needs.

1. Thermal Power Plant
Steam (Vapour) Power Plant
Coal based Power Plant
Rankine cycle Power Plant
Prepared by: Nimesh Gajjar

2.  Sources of energy:
Primary energy sources Secondary energy sources
Coal, Oil, Nuclear fuels, Water → Electricity
Wood → Heat
Candles, Oil lamps → Light
 Conventional sources of energy → Non-renewable sources of energy
Non-conventional sources of energy → Renewable sources of energy
 Fossil fuels → Coal, Oil, Natural gas

3. Power Plant: Power plant is an assembly of equipments that produces and
delivers mechanical and electrical energy.
Types of power plant
1. Non-conventional Energy Source
a. Solar energy
b. Wind energy
c. Geothermal energy
d. Tidal energy
e. Biomass energy
2.Conventional Energy Sources
a. Solid, Liquid and gaseous fuels
b. Hydraulic energy

4. Classification of Power plants
 Power plants using
conventional (non-
renewable) sources of energy
 Steam power plant
 Nuclear(Atomic) power plant
 Diesel power plant
 Gas power plant
 Hydro electric(Hydel) power
plant
 Power plants using Non-
conventional(renewable)
sources of energy
 Solar thermal power plant
 Wind powered
generation(aerogeneration)
 Wave power plant
 Tidal power plant
 Geothermal power plant
 Bio-mass power plant
 Oceanthermal power plant

5. INDIAN POWER SCENARIO GENERATION BY)
 58.7 % - Coal
 25.4 % - Hydro
 10.7 % - Gas based
 02.5 % - Nuclear
 2.7 % - Non- Conventional & Diesel

6. - Steam power plant is an energy converter
- INTRODUCTION:
Chemical energy
Thermal energy
Steam energy
Mechanical energy
Electrical energy
Chemical energy of fuel
Heat Energy
Steam Energy
Mechanical Energy
Electrical Energy
Oxidation
Heat energy is transfered to fluid in
Boiler
Heat energy is converted into
Mechanical energy by Prime
mover
Mechanical energy is converted
into Electrical energy by Generator

7. Steam (Thermal) Power Plant
 Fuel : Coal or Oil
 Main parts : Boiler, Turbine,
Generator , condenser, pump
1 simplepowergen.swf

8. Steam (Thermal) Power Plant
nimymechRankineCycle.swf

9. The Simple Ideal Rankine Cycle
© The McGraw-Hill Companies, Inc.,1998
steamPowerPlant.swf

10. Simple Rankine Cycle Diagram
AIR, GAS
STEAM
WATER
LEGEND
Matteran16animation.swf

11. Steam (Thermal) Power Plant

13. Steam Turbines
 Turbines perform the energy conversion in two steps:
 Step 1: Thermal energy of the steam to kinetic energy
of the steam
 Step 2: Kinetic energy of the steam to mechanical
energy of the rotor

15. The Concept Of Producing Electercity
Acgeneratorbasic.swf

16. How a coal power station works.mp4

17. Main parts:
Furnace Boiler Generator
Condenser
&
Cooling tower
Chimney Turbine
Heat Recovery parts:
Economizer Air Heaters Deaerator

21. Diagram of a typical coal-fired thermal power
station
genAnimation.swf

23. Main par ts of th e p lan t are
1 . Co al co n v eyo r
2 . Sto k er
3 . Pu lv er iser
4 . Bo iler
5 . Su p er h eater
6 . Reh eater
7 . A ir p r eh eater
8 . D eaer ato r
9 . Tu r b in e(PRI ME MO V ER)
1 0 . Co n d en ser
11 . Co o lin g to w er s
1 2 . Electr o static p r ecip itator
1 3 . Smo k e stack
1 4 . Gen erato r
1 5 . Tr an sf o rmer s
1 6 . Co n tr o l r o o m & Sw itch yar d

24. Steam (Thermal) Power Plant…
 Coal and Ash circuit
 Pulverised coal from the storage area
(called stack) is taken to the boiler by
means of coal handling equipment such as
belt conveyors, bucket elevators etc.
Note : A thermal power plant of 400 MW
capacity requires 5000 to 6000 tonnes of
coal per day.
 After the pulverised coal is burnt at 15000C
to 20000C by combustion it gets collected
in the ash pit.
 It is removed from the ash pit by ash
handling systems like belt conveyors, screw
conveyors etc.
Note : A thermal power plant of 400 MW
capacity requires 10 hectares area per year
if ash is damped to a height of 6.5 metres.

25. Steam (Thermal) Power Plant…
 Air and flue gas circuit
 The air from the atmosphere gets heated in
the air preheater. The air receives its heat
from the hot flue gases passing to the
chimney.
 The hot air enters the boiler and helps in
combustion of fuel in the boiler.
 The flue gases, after combustion in the boiler
furnace, pass around the boiler tubes, heating
the water present in the tubes.
 The flue gases then pass through a dust
collector which removes any dust or solid
particles.
 The filtered flue gas passes through the
economiser and preheater and is forced out
through the chimney by a draught fan.

26. Steam (Thermal) Power Plant…
 Feed water and steam circuit
 The superheated steam from the boiler enters the
steam turbine. The superheated steam temperature
is about 6000C at a pressure of 30 Mpa(300
kg/cm2)
 The steam expands in the turbine causing the
turbine blades to rotate. After doing mechanical
work on the blades and loosing its energy, the
steam becomes wet and the pressure of steam
becomes less.
 The wet steam passes through a condenser where it
completely becomes water. The condensed water
that has a temperature of 300C to 400C is collected
in a tank called hot well.
 The water from the hot well is fed into the boiler
through the economiser.
 The economiser preheats the water before entering
the boiler. The economiser receives its heat from
the flue gases leaving the boiler .
 Preheating the feed water in the economiser
increases the boiler efficiency and helps quicker
production of steam.

27. Steam (Thermal) Power Plant…
 Cooling water circuit
Water is circulated around the condenser
to condense the steam coming out of the
turbine.
Cooling water enters the condenser at
100C to 150C and leaves at 200C to 250C.
Plenty of water is required for
condensing the steam in the condenser.
The water may be taken from sources
such as river or lake.

28. SITE SELECTION FOR THERMAL POWER
PLANT
A few important factors to be considered for the selection of site for
thermal plants are listed below:
 Availability of Coal
 Ash Disposal Facility
 Space Requirements
 Nature of Land
 Availability of Water
 Transport Facilities
 Availability of a Labour
 Public Problems
 Size of the Plant

29. - Advantages:

30. - Disadvantages:
1
• Pollution
2
• Low efficiency
3
• Position ( near the river)
need cooling water

31. Steam (Thermal) Power Plant…
 Advantages of thermal power plant :
 Low initial cost
 Since located near the load centre, the cost of transmission and the losses
due to transmission are considerably reduced.
 The construction and commissioning of thermal power plant takes lesser
period.
 Disadvantages of thermal power plant:
 Fuel is a non-renewable source of energy.
 Efficiency decreases with decreasing load.
 Cost of power generation is high.
 Smoke produced by burning the fuel causes air pollution.
 Life of thermal power plant is 25 years. The efficiency decreases to less
than 10% after its life period.
 Turbines has a high running speed of 3000 to 4000 rpm.

32. nimymechpowerplant_make_e.swf
nimymechpowerplant_name_e.swf