Overview of IO-Link

1. Russell Smith
Balluff Limited
IO-Link Technology

2. 2PROFIBUS UK
what is IO-link?

3. 3PROFIBUS UK 3
not another bus system!
point to point communications protocol from the
fieldbus to the sensor and actuator level.
upto20M
Pulse-width modulated 24V
Baud rates: 4.8 kBit/s (COM1), 38.4 kBit/s (COM2), 230,4 kBits/s (COM3)
Pin Signal Description
1 L + 24 Volt
2
3 L - 0 Volt
4 C / Q
IO-Link
communication
+ switching signal

4. 4PROFIBUS UK 4
an open standard
standard - IEC 61131-9
network neutral

5. 5PROFIBUS UK 5
IO-Link system basic components:
IO-Link master
… acts as a gateway between the IO-Link device and the higher level communication
system, such as a fieldbus (Profinet, EtherNet/IP, etc.) or a device-specific backplane bus.
IO-Link device
… is the field device with communication capability: sensors, switching
devices, valve terminals, RFID devices, indicator lights, etc.
3-core unshielded standard cable – up to 20M long
… is the standard interface between IO-Link master and device
IODD and engineering tool
… are used to configure and assign parameters to the IO-Link system and devices.

6. 6PROFIBUS UK 6
IO-Link devices
many different IO-Link devices are available.

7. 7PROFIBUS UK 7
IO-Link masters
panel
mounted unit
with terminals
IP67 field I/O
module
additional slice on existing PLC

8. 8PROFIBUS UK
why IO-Link?

9. 9PROFIBUS UK 9
easier handling of measurement devices
lower cost – no analogue card
lower cost vs IE networked device
less wiring effort
traditionally
better
best

10. 11PROFIBUS UK 11
low cost per I/O point – 496 I/O on one IP address
low cost
high density
less addresses

11. 12PROFIBUS UK 12
extensive diagnostics
available on sensors/devices and
sensor hubs
troubleshoot problems quickly
maximise up-time

12. 13PROFIBUS UK 13
extensive diagnostics
Short circuit – LED for each I/O port
Short circuit does not impair the unit
Sensor/actuator under voltage LED for each I/O port

13. 14PROFIBUS UK 14
simplify valve manifold wiring
reduced installation time
reduced cost

14. 16PROFIBUS UK 16
IO-Link safety

15. 17PROFIBUS UK 17
HMI
parameterisation – std pressure sensor
HMI
HMIHMIHMI
HMI

16. 18PROFIBUS UK
parameterisation – std pressure sensor
Time consuming configuration of 10 – 15 Parameter.
(e.g. upper/lower Pressure point, Hysteresis, Time – or
Pressure window)
Machine Tools have often more than 10 Pressure sensors
Error prone due to manual entry
Very bad when Sensor failure / Sensor exchange
(especially during night shift)
Manual
configuration

17. 19PROFIBUS UK 19
parameterisation – std pressure sensor
HMI
HMI
HMI
HMI

18. 20PROFIBUS UK 20
HMI integrated in sensor for set up
means additional cost.
Expensive high-pressure hydraulic
hoses
parameterisation – std pressure sensor
machine tool
Additional cost for protective
housing for sensors in the machine

19. 21PROFIBUS UK 21
parameterisation – pressure sensor with IO-Link
E.g. machine tool

20. 22PROFIBUS UK 22
PLC
Function-
blocks
Vendor_ID
Device_ID
Param1: 50bar
Param2: 100bar
Param3: 200ms
Step 1
Identify device
Step 3
Get Parameter Set
Step 2
Check identity
Step 4
Write Parameter
Set
parameterisation – pressure sensor with IO-Link

21. 23PROFIBUS UK 23
parameterisation – pressure sensor with IO-Link
sensor installed at point of measurement
no expensive measurement cables - use std
un-shielded 3-wire standard cables
no protection case
no sensors with HMI but reliable
parameterisation via controller and HMI of
the machine
decentralised diagnostics for sensors

22. 24PROFIBUS UK 24
parameter server
IO-Link V1.1 master

23. 25PROFIBUS UK 25
automated tool changes
IO-Link inductive couplers for non-contact
signal transmission

24. 26PROFIBUS UK 26
an i4.0 enabler
ERP
MES
SCADA
PLC
Network
Sensors and Actuators
Enterprise Level
Control Level
Management Level
Plant Control Level
Field Level
Sensor / Actuator Level

25. 27PROFIBUS UK 27
unabated IO-Link success!

26. 28PROFIBUS UK 28
how IO-Link?

27. 29PROFIBUS UK 29
connect the master to the PLC and install the GSDML
file
drag and drop the relevant file and make the
PROFINET connection from the PLC to the master in
TIA Portal
IO-Link master configuration

28. 30PROFIBUS UK 30
IO-Link master configuration
Drag the appropriate (process
data length) IOL input / output
byte from the catalogue and
name & address the module

29. 31PROFIBUS UK 31
device configuration from PLC or using parameter
server
1. controller parameter storage – parameterisation
from the PLC using the function block
2. IO-Link master ver 1.1 parameter server

30. 32PROFIBUS UK 32
device configuration with USB master or
webserver
3. PC storage with USB master
4. webserver entry with IO-Link master

31. 33PROFIBUS UK 33
device configuration with Device Manager

32. 34PROFIBUS UK 34

33. 35PROFIBUS UK 35
device configuration with integrated web server

34. 36PROFIBUS UK 36
device configuration with integrated web server

35. 37PROFIBUS UK 37
device configuration - manual
Manual
configuration
5. Manual configuration

36. 38PROFIBUS UK 38
THANKS FOR LISTENING!
Russell Smith
Product Marketing Manager Industrial Networking
+44 (0)777 331 7984
russell.smith@balluff.co.uk
www.linkedin.com/in/russellsmithindustrymanager