Se ha denunciado esta presentación.
Utilizamos tu perfil de LinkedIn y tus datos de actividad para personalizar los anuncios y mostrarte publicidad más relevante. Puedes cambiar tus preferencias de publicidad en cualquier momento.


3.206 visualizaciones

Publicado el

its understanding about types of dynamometer and that application and its practical uses.
this is very usefull in engineering.

Publicado en: Educación
  • Inicia sesión para ver los comentarios


  1. 1. Theory of machines Dynamometers Prepared by : Urvesh Dungarani 140050119506 Guided by : Nirmal Kushwala
  2. 2.  Sometimes the brakes are not only used to retard or stop the motion but may also be used to measure power absorbed during braking. Such brakes which have a provision to measure absorbed power are called “Dynamometers”.  Thus dynamometer is a device which is used to measure the frictional resistance. By knowing frictional resistance we can determine torque transmitted and hence the power of engine.  Dynamometer can be used either to measure force, torque or power.
  3. 3. 1. Absorption dynamometer - Prony brake dynamometer - Rope brake dynamometer 2. Transmission dynamometer - Belt transmission dynamometer - Epicyclic dynamometer - Torsion dynamometer
  4. 4. In this type of dynamometer, the work done by engine is absorbed by frictional resistance of brake is converted into heat during process of measurement. These dynamometers can be used for measurement of moderate powers only. Various types of dynamometer are discussed below…
  5. 5. It is simplest form of an absorption type dynamometer. It consists of two wooden blocks clamped together on a revolving brake drum whose power is to be measured. The bolts and nuts are used to clamp the blocks. In order to adjust the pressure on pulley to control its speed, helical spring is provided between nut and upper block.
  6. 6. Friction between blocks and pulley tends to rotate the blocks in the direction of rotation of drum. Suspended weight W at the end of lever prevents this tendency. Applied weight is so adjusted that the lever remains in horizontal position by tightening the nuts to get the constant engine speed. With the help of above equation, we can calculate the brake power. Brake Power P = 2π NT where, T = Weight applied (W) × distance (l) N = speed of shaft
  7. 7. It consists of one, two or more ropes wrapped over rim of a pulley keyed to shaft of engine. In order to prevent slipping of rope over pulley, U shaped wooden blocks are placed at certain intervals on circumference of pulley. The upper end of rope is attached to a spring balance while the lower end carries a dead weight W. If high power is produced, then heat is generated due to friction between rope and pulley or drum. To prevent this, water is provided to cool the pulley.
  8. 8. Here, W = dead weight or suspended weight S = spring balance reading D = diameter of pulley or drum N = speed of engine d = diameter of rope (W-S) = net brake load If diameter of rope is neglected, Brake power, P = (W-S)πDN/60 Watt
  9. 9. Hydraulic dynamometer consists of two elements called rotating disc and casing. The rotating disc is attached to engine shaft whose power is to be measured and revolves inside the casing.
  10. 10. The casing and rotating disk have semi elliptical recesses forming a chamber through which water is flowing. When water flow through chamber with high pressure the vertices are set up in the chamber which tends to rotate the casing also. This tendency of rotation of casing is restricted by braking system that measure the torque and hence the power of engine.
  11. 11. It consists of endless or continuous belt run over the driving pulley A, driven pulley B and intermediate pulleys C and D. The driven pulley A is rigidly fixed to shaft of an engine whose power is to be measured. The driven pulley B is fixed to another shaft to which power is to be transmitted. The intermediate pulleys C and D rotate on a pin fixed to a lever having fulcrum at midpoint of two pulleys. A balancing weight is provided in lever to initially keep it in equilibrium. Two stops S1 and S2 are used to limit the motion of lever.
  12. 12. The weight of suspended mass at one end of lever balances the difference in tensions of tight and slack sides of belt. Power of the engine : P = (T1-T2)×πDN/60 The working of belt transmission dynamometer is shown in the video…
  13. 13. Epicyclic train dynamometer measures power while it is being transmitted from driving to driven shaft. It consists of simple gear train . The lever is pivoted about common axis of driving and driven shaft. The power is transmitted from one gear to another through pinion. A balancing weight is adjusted to one end of lever to keep it in equilibrium at rest.
  14. 14. Two stops are used to limit the movement of lever. Power transmitted = WLR×π/(60×a) where, W = dead weight L = lever arm N = speed of engine
  15. 15. When power is transmitted along a shaft, the driving end shifts through a small angle relative to the driven end. Torque transmitted is directly proportional to the angle of twist. Therefore, a torsion dynamometer works on principle of angle of twist. Torsion dynamometer can measure large powers as in case of power transmitted along the propeller shaft of a turbine or a motor vessel. Torsion equation is : where θ = Angle of twist in radians, and J = Polar moment of inertia of the shaft.
  16. 16. It consists of two discs A and B fixed on a shaft at convenient distance. Behind disc A powerful electric lamp is fixed on bearing shaft. To the right of disc B an eye piece is fitted on shaft bearing. When torque or power is transmitted through shaft, it twists so that disc B lags behind disc A.
  17. 17. In this case, all four do not remain in same line, hence the light of lamp is not visible through the eye piece as shown in fig. The eye piece is moved circumferentially so that all four are again in same line and light of lamp is visible through the eyepiece as shown in fig. The angle of twist can be measured up to 1/100th of a degree.