Designing a Concrete Beam Using the New AS3600:2018 - Webinar Slides - ClearCalcs

Designing a Rectangular
Concrete Beam Using AS3600-
2018
Understanding the design process using the
newly-updated standard
Brooks H. Smith, CPEng, PE, MIEAust, NER, RPEQ
brooks.smith@clearcalcs.com

Outline
• Introduction
• Overview of Major Changes
• Designing a Rectangular Beam
• Flexural Capacity
• Shear Capacity
• Deflection
• Stability Checks
• Crack Control
• Example Beam Calculations
• Conclusion & Questions
218 October 2018 ClearCalcs.com | FEA Structural Design in the Cloud

Introduction – About the Presenter
• Chartered Professional Engineer
• MCivE, MIEAust, NER, RPEQ, P.E. (USA)
• Currently the lead engineering developer for ClearCalcs
• Recently released concrete beam calculator for AS3600-2018
• 8 years of previous experience in:
• Forensic structural engineering, specialising in reinforced and PT concrete
• Research fellowship in system behaviour of thin-walled steel
• Structural engineering R&D consulting, specialising in cold-formed steel
3
Brooks H. Smith

About ClearCalcs.com
ClearCalcs.com | FEA Structural Design in the Cloud 4
More Accurate
Design more accurately with
unrestricted and accessible
FEA analysis
Eliminates Wasted Time
Eliminate time wasted using
clunky methods or waiting for
software licenses to free up
Available Everywhere
Empower engineers to work
effectively from office, home,
or site
ClearCalcs helps engineers design
without compromise by bringing
together powerful FEA analysis with
easy to use design tools for concrete,
steel, and timber.
Explore our range at clearcalcs.com
Intro Video Hyperlink

Introduction – Today’s Goals
• To be able to design a rectangular reinforced concrete beam to
AS3600-2018
• No torsion forces
• No prestressing or post-tensioning
• I’ll point out important points where T-beams differ
• Differences to 2009 code will only be broadly addressed
• Detailing will only be broadly addressed
• Provisions are very prescriptive and depend on precise geometries and layout
• We’ll distribute this slide deck and video after the webinar
• Please ask quick questions as I go – best to answer while on the
topic
• I’ll save involved questions until the end

Outline
• Introduction
• Shear Capacity
• Deflection
• Crack Control

Overview of Major Changes
• Phi factors are revised
• Mostly simplified, increased
• Shear procedure significantly redone
• New methodology for shear strength of concrete
• Rectangular stress block formulas modified
• Deflection calculations modified
• Alternative method & effective moment of inertia changes
• Shrinkage & creep calculations heavily revised
• Simplifying conservative assumptions
• Also: Punching shear, SFRC, some detailing, fatigue, diaphragms
• Though these are outside the scope of this webinar

Phi Factors Updated (Table 2.2.2)
• Many limit states increased by 0.05
• Shear and torsion for most members with Class N reo: 0.7 → 0.75
• Tension with Class N reo: 0.8 → 0.85
• Compression: 0.6 → 0.65
• Bending without axial increased:

Shear Procedure Redone (Cl 8.2)
• Procedure almost completely redone
• Forget all the equations you previously learned
• Largely adopted the United States ACI procedure
• Generally simpler
• Explicit alternate (simplified) clauses for non-prestressed beams
• Torsion (formerly Section 8.3) merged into shear (Section 8.2)

Rectangular Stress Block Formulas (Cl
8.1.3)
• Formulas for the rectangular stress block assumed in flexural
loading have been modified
• Strength of the concrete has less effect on shape of block
• Already modified in 2009’s A1 revision, further modified in 2018

Deflection Calculations Modified (Cl 8.5)
• Effective moment of inertia equation modified
• 2009’s A2 added in alternative (simpler) non-prestressed
equations
• 2018 fixes an important mistype in there, but otherwise unchanged
since A2
• Parentheses are important!

Shrinkage & Creep Revised (Cl 3.1.7-8)
• Shrinkage
• Same equations, but factors simplified, made a little more conservative
• Adelaide and Perth, you are no longer lumped into “elsewhere”!
• Creep
• Was completely revised in 2009’s A2 revision
• 2018 further adds a k6 factor to account for non-linear creep at high
stress

Outline
• Introduction
• Shear Capacity
• Deflection
• Crack Control

Designing a Rectangular Concrete Beam
• Calculate your demands by AS1170.X
• Limit states which must be checked:
• Positive moment flexural capacity (midspans)
• Negative moment flexural capacity (supports)
• Shear capacity
• Deflection
• Stability
• Crack control

Geometric Derivatives
• First, make sure you’ve calculated some of your basic geometry:
• Ast = total area of tension steel
• d = depth to centroid of outer layer of tension steel
• Asc = total area of compression steel
• dsc = depth to centroid of outer layer of compression steel
• Asv = total area of transverse steel (shear reinforcement)
• n = ratio of elastic modulus of steel to elastic modulus of concrete
• Ig = gross second moment of area / moment of inertia
• Ag = gross cross-sectional area

Flexural Capacity - Uncracked Beam
Analysis
• Essentially an elastic composite beam calculation using
mechanics
• Needed later for minimum bending strength calculations
16
𝐴𝐴𝑠𝑠𝑠𝑠,𝑡𝑡𝑡𝑡 = 𝑛𝑛 − 1 𝐴𝐴𝑠𝑠𝑠𝑠
𝐴𝐴𝑠𝑠𝑠𝑠,𝑡𝑡𝑡𝑡 = 𝑛𝑛 − 1 𝐴𝐴𝑠𝑠𝑠𝑠
𝑑𝑑𝑛𝑛,𝑢𝑢𝑢𝑢𝑢𝑢𝑢𝑢 =
∑ 𝑎𝑎𝑎𝑎𝑎𝑎𝑎𝑎 ∗ [𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐]
∑[𝑎𝑎𝑎𝑎𝑎𝑎𝑎𝑎]
𝐼𝐼𝑔𝑔,𝑢𝑢𝑢𝑢𝑢𝑢𝑢𝑢 = 𝐼𝐼𝑔𝑔 + 𝐴𝐴𝑔𝑔 𝑑𝑑𝑛𝑛,𝑢𝑢𝑢𝑢𝑢𝑢𝑢𝑢 −
𝐷𝐷
2
2
+𝐼𝐼𝑠𝑠𝑠𝑠,𝑡𝑡𝑡𝑡 + 𝐴𝐴𝑠𝑠𝑠𝑠,𝑡𝑡𝑡𝑡 𝑑𝑑𝑛𝑛,𝑢𝑢𝑢𝑢𝑢𝑢𝑢𝑢 − 𝑑𝑑𝑠𝑠𝑠𝑠
2
+𝐼𝐼𝑠𝑠𝑐𝑐,𝑡𝑡𝑡𝑡 + 𝐴𝐴𝑠𝑠𝑐𝑐,𝑡𝑡𝑡𝑡 𝑑𝑑𝑛𝑛,𝑢𝑢𝑢𝑢𝑢𝑢𝑢𝑢 − 𝑑𝑑𝑠𝑠𝑐𝑐
2
𝑍𝑍 =
𝐼𝐼𝑔𝑔,𝑢𝑢𝑢𝑢𝑢𝑢𝑢𝑢
min(𝑑𝑑𝑛𝑛,𝑢𝑢𝑢𝑢𝑢𝑢𝑢𝑢, 𝐷𝐷 − 𝑑𝑑𝑛𝑛,𝑢𝑢𝑢𝑢𝑢𝑢𝑢𝑢)

Flexural Capacity – Ultimate (Cl 8.1.3)
• Based upon rectangular stress block theory
• Assuming steel will yield (usually desired)
17
𝑘𝑘𝑢𝑢 =
𝐴𝐴𝑠𝑠𝑠𝑠 𝑓𝑓𝑠𝑠𝑠𝑠
𝛼𝛼2 𝑓𝑓𝑐𝑐
′
𝛾𝛾𝛾𝛾𝛾𝛾 + 𝐴𝐴𝑠𝑠𝑠𝑠 𝑓𝑓𝑠𝑠𝑠𝑠
𝛼𝛼2 𝑓𝑓𝑐𝑐
′
𝛾𝛾𝑘𝑘𝑢𝑢 𝑑𝑑
𝑑𝑑𝑛𝑛 = 𝑘𝑘𝑢𝑢 𝑑𝑑
𝑀𝑀𝑢𝑢 = 𝐴𝐴𝑠𝑠𝑠𝑠 𝑓𝑓𝑠𝑠𝑠𝑠 ∗ 𝑑𝑑 −
𝛾𝛾𝑘𝑘𝑢𝑢 𝑑𝑑
2
Stress Strain

Flexural Capacity – Minimums (Cl 8.1.6)
• Minimum moment capacity required:
• …unless failure will not lead to reduced collapse load or sudden collapse
• For reinforced beams, this means a minimum quantity of tensile steel:
• In other words, you must meet one of the two above equations
18
with no prestressing → 𝑀𝑀𝑢𝑢,𝑚𝑚𝑚𝑚 𝑚𝑚 = 1.2 𝑍𝑍 𝑓𝑓𝑐𝑐𝑐𝑐.𝑓𝑓
′

Flexural Capacity – Finalising (Cl 8.1)
• Check that concrete will not crush (Cl 8.1.3 / 8.1.5)
• Calculate your ɸ (capacity) factor:
19
𝜀𝜀𝑐𝑐 =
⁄𝑓𝑓𝑠𝑠𝑠𝑠 𝐸𝐸𝑠𝑠 𝑘𝑘𝑢𝑢
1 − 𝑘𝑘𝑢𝑢
≤ 0.003
18 October 2018
Final Capacity = 𝜙𝜙𝑀𝑀𝑢𝑢
ClearCalcs.com | FEA Structural Design in the Cloud

Shear Capacity – General (Cl 8.2.1-3)
• For most flexural beams, may design by Sectional Design
Method
• Unless near discontinuities (see Cl 8.2.2, not yet included)
• Calculate your effective shear depth
• 𝑑𝑑𝑣𝑣 = max(0.72𝐷𝐷, 0.9𝑑𝑑)
• Make sure you use the correct 𝑑𝑑 – based on tension reo! (Cl 8.2.1.9)
• 𝑏𝑏𝑣𝑣 = 𝑏𝑏𝑤𝑤 = 𝐵𝐵 for rectangular beams
• Shear fitments / ligatures required if 𝑉𝑉∗ > 𝜙𝜙𝑉𝑉𝑢𝑢𝑢𝑢 or if 𝐷𝐷 ≥ 750𝑚𝑚𝑚𝑚
• And the minimum cross-sectional area of fitments is the following:

Shear Capacity – Concrete (Cl 8.2.4)
• Main equation:
• Can usually use a simplified method to calculate 𝑘𝑘𝑣𝑣 (Cl 8.2.4.3)
• For reo with 𝐹𝐹𝑠𝑠𝑠𝑠 ≤ 500𝑀𝑀𝑀𝑀𝑀𝑀, 𝑓𝑓𝑐𝑐
′ ≤ 65𝑀𝑀𝑀𝑀𝑀𝑀, maximum aggregate size ≥ 10mm
• Mandatory sanity checks (Cl 8.2.4.4-5):
• If creep, shrinkage, differential temperature > 10% of stress, must consider
• If load reversal can cause cracking, then 𝑉𝑉𝑢𝑢𝑢𝑢 = 0

Shear Capacity – Steel (Cl 8.2.5)
• 𝛼𝛼𝑣𝑣 = angle of shear fitments, 𝜃𝜃𝑣𝑣 = 36°
• (these are the same equation)
• Can only include steel strength if you have at least minimum
fitments
• 𝐴𝐴𝑠𝑠𝑠𝑠 ≥ 𝐴𝐴𝑠𝑠𝑠𝑠,𝑚𝑚𝑚𝑚 𝑚𝑚

Shear Capacity – Finalising (Cl 8.2.1-3)
• Check that concrete will not crush:
• Total shear capacity:
• 𝑉𝑉𝑢𝑢 = min(𝑉𝑉𝑢𝑢𝑢𝑢 + 𝑉𝑉𝑢𝑢𝑢𝑢, 𝑉𝑉𝑢𝑢.𝑚𝑚𝑚𝑚𝑚𝑚)
• Calculate your 𝜙𝜙 factor:
• That is: 𝜙𝜙 = 0.75 if 𝐴𝐴𝑠𝑠𝑠𝑠 ≥ 𝐴𝐴𝑠𝑠𝑠𝑠.𝑚𝑚𝑚𝑚 𝑚𝑚 and 𝑉𝑉𝑢𝑢 < 𝑉𝑉𝑢𝑢.𝑚𝑚𝑚𝑚𝑚𝑚

Deflection – General (Cl 8.5)
• Three methods:
1. Refined – take all strain properties and staged construction into account
2. Deemed-to-conform – set span-to-depth ratios, etc
3. Simplified – our method, likely your most common
• Short-term deflection based on effective second moment of area:
• 𝑏𝑏𝑒𝑒𝑒𝑒 = 𝑏𝑏𝑤𝑤 = 𝐵𝐵 for rectangular beams

Deflection – Long-Term (Cl 8.5.3.2)
• Two methods:
1. Calculate shrinkage and creep by Cl 3.1.7-8 – often a tedious process
2. Estimate factor – our method, likely your most common
• Additional long-term deflection factor:
• 𝛿𝛿𝑙𝑙𝑙𝑙 = 𝛿𝛿𝑠𝑠𝑠𝑠 + 𝑘𝑘𝑐𝑐𝑐𝑐 𝛿𝛿𝑠𝑠𝑠𝑠
• Calculated at midspan for interior spans, and at supports for cantilevers

Stability Checks (Cl 8.9)
• May use either:
• Full stability analysis
• Deemed-to-conform – our method
• Interior spans:
• 𝐿𝐿1 = distance between lateral restraints
•
𝐿𝐿1
𝑏𝑏𝑒𝑒𝑒𝑒
≤ min
180𝑏𝑏𝑒𝑒𝑒𝑒
𝐷𝐷
, 60
• Cantilevers:
• 𝐿𝐿𝑛𝑛 = clear projection of cantilever
•
𝐿𝐿𝑛𝑛
𝑏𝑏𝑒𝑒𝑒𝑒
≤ min
100𝑏𝑏𝑒𝑒𝑒𝑒
𝐷𝐷
, 25

Crack Control (Cl 8.6)
• Usually only need to meet:
• For beams that will be fully enclosed in the building after construction,
and cracking will not affect beam’s function, then:
27
≤ 100mm ≤ 300mm
a)
b)

Shrinkage & Creep (Cl 3.1.7-8)
• Shrinkage (Cl 3.1.7):
• Sum of autogenous strain (𝜀𝜀𝑐𝑐𝑐𝑐𝑐𝑐)
+ drying strains (𝜀𝜀𝑐𝑐𝑐𝑐𝑐𝑐)
• May typically simply look up in table:
• Creep (Cl 3.1.8):
• 𝜎𝜎0 = stress due to sustained loads
• 𝐸𝐸𝑐𝑐 = �
𝜌𝜌1.5
∗ 0.043 𝑓𝑓𝑐𝑐𝑐𝑐𝑐𝑐, 𝑓𝑓𝑐𝑐𝑐𝑐𝑐𝑐 ≤ 40𝑀𝑀𝑀𝑀𝑀𝑀
𝜌𝜌1.5
∗ 0.024 𝑓𝑓𝑐𝑐𝑐𝑐𝑐𝑐 + 0.12, 𝑓𝑓𝑐𝑐𝑐𝑐𝑐𝑐 > 40𝑀𝑀𝑀𝑀𝑀𝑀

Outline
• Introduction
• Shear Capacity
• Deflection
• Shrinkage, Creep, etc

Example Beam #1 – Simply Supported
30
3500 mm
3x N12
130mm
300mm
50mm
• Office building floor beam
• No transverse shear reinforcement
• Load width of 1000mm
• 𝑓𝑓𝑐𝑐
′
= 32𝑀𝑀𝑀𝑀𝑀𝑀
G = 0.9 kPa
Q = 1.5 kPa
18 October 2018
Showing methods and formulas
using ClearCalcs’s new reinforced
concrete calculator

Example Beam #2 – Complex Beam
31
3x N10
130mm
300mm
50mm
2x N12
30mm
2x N10
3x N12
Positive Moment Regions Negative Moment Regions
G = 0.9 kPa
Q = 1.5 kPa
• Retail building floor beam
• R6 shear reinforcement @ 200mm
near supports
• Load width of 1500mm
• 𝑓𝑓𝑐𝑐
′
= 32𝑀𝑀𝑀𝑀𝑀𝑀
3500 mm 4500 mm 2000 mm
18 October 2018
Ex #1 Beam @ 7000mm

Outline
• Introduction
• Shear Capacity
• Deflection
• Shrinkage, Creep, etc

Summing It Up
• Major updates in 2018 include:
ɸ factors • Shear • Rectangular stress block • Deflection •
Shrinkage/Creep
• Beam design checks at all sections include:
• Flexure: Uncracked analysis → Rectangular stress block → Minimum
checks
• Shear: Concrete contribution → Steel contribution → Maximum check
• Deflection: Effective 2nd moment of area → Long-term factor
• Stability: Maximum span-to-breadth ratios
• Crack Control: Minimum steel & maximum reo spacings
• We performed examples with simply supported and complex
beams

Questions?
3418 October 2018
Explore our broad range of calculations
at clearcalcs.com
Already available:
- Timber
- Steel
- Concrete
- Connections
- Retaining walls
In development:
- Cold-formed steel
- Advanced connections
- Foundations
- Retaining walls
And watch for more free webinars
upcoming on designing other types of
members and connections!
Q: Will you be adding C sections
A: We will be implementing these, starting with cold formed
steel C sections. Hot rolled will be added at a later point
Q: Is % reinforcement available in ClearCalcs?
A: If you click Details > on the top right of the calculation, and
then toggle from “Summary” to “Detail” additional info.
Q: Has 2009 requirement to include shear steel if V*>Vu been
changed?
A: yes, it has been replaced in 2018. You only need to include
shear steel if V* exceeds phi factor * contribution from concrete
Q: Can you calculate the beam’s reinforcement using any type
of load?
A: Yes, you can calculate using any type of load (e.g. wind,
seismic) and may include triangular, point load, or moments.

Appendix
About ClearCalcs
ClearCalcs Pty Ltd 3518 October 2018

Happy Engineers Using ClearCalcs
ClearCalcs has been used in over 250,000 designs by a growing number of engineers across Australia.
“Faster, more accurate design,
easier to modify calculations,
just all around better”
Murray P.
Vision Engineers
“ClearCalcs has streamlined my
design process with its simplicity
and convenience”
Andrew G.
Intrax Consulting Engineers
“A great tool to ensure quality,
verifiable, and professionally
presented comps”
Adam M.
AM-A Engineers
“Far superior product to similar
I've used and appears to be
improving much more rapidly”
Peter M.
Intrax Consulting Engineers

The ClearCalcs Team
A growing team of passionate engineers and programmers

Key Advantages
ClearCalcs Pty Ltd 38
ClearCalcs is designed for the modern efficiency focused engineering practice
18 October 2018

Designing a Concrete Beam Using the New AS3600:2018 - Webinar Slides - ClearCalcs

Recomendados

Recomendados

Más contenido relacionado

La actualidad más candente

La actualidad más candente (20)

Similar a Designing a Concrete Beam Using the New AS3600:2018 - Webinar Slides - ClearCalcs

Similar a Designing a Concrete Beam Using the New AS3600:2018 - Webinar Slides - ClearCalcs (20)

Último

Último (20)

Designing a Concrete Beam Using the New AS3600:2018 - Webinar Slides - ClearCalcs