IDT offers the industry's most integrated and advanced wireless power transmitter solutions for magnetic inductance-based applications. IDT has pioneered this market by introducing the world's first true single-chip wireless power transmitter IC and the industry's first multi-mode capable single-chip wireless power receiver IC. This video introduces IDT's rich portfolio of inductive charging transmitter ICs and solutions. These solutions address various transmit coil and input voltage configurations. Presented by Jack Deans, Field Applications Manager, Integrated Device Technology, Inc. Learn more about IDT's wireless power solutions at www.wirelesspowerbyidt.com.

1. Integrated Device Technology
WIRELESS POWER
TRANSMITTER SOLUTIONS
www.IDT.co
PAGE 1

2. IDTP9036/A 12V Transmitter IC
IDTP9036/A
High Eff. Synchronous
Half Bridge Inverter
2 Way Secure
Authentication
 IDTP9036: WPC 1.0.1 Certified
 IDTP9036A: WPC 1.1 Certified
 Support A6 Triple Coil or Single Coil
Modulation/
Demodulation
Thermal Loop
Control
OTP, UVLO
OVP, OCP
 Up to 7.5W Power Transfer
 9V – 16V Operating Voltage Range
 Advanced Foreign Object Detection (FOD)
 Proprietary Base to Mobile Communication
for 2-Way Secure Authentication
Status & Power
Good Indicator
Multi-Coil
Management
Embedded
MicroController
RAM
 Integrated Half-Bridge Inverter
Proprietary
Back Channel
Communication
High Eff. Buck
Converter
ADC
I2C
 Over Temp/Voltage/Current Protection
 I2C Interface
 6x6mm 48-TQFN Package
www.IDT.co
FOD
Foreign Object
Detection
PAGE 2
ROM
Clock

3. IDTP9035/A 5V Transmitter IC
IDTP9035/A
 IDTP9035: WPC 1.0.1 Certified
High Eff. Synchronous
Half Bridge Inverter
2 Way Secure
Authentication
 IDTP9035A: WPC 1.1 Certified
 Support A5 and A11 Coils
 Up to 7.5W Power Transfer
Thermal Loop
Control
OTP, UVLO
OVP, OCP
 5V Input Operating Voltage
 Advanced Foreign Object Detection (FOD)
 Proprietary Base to Mobile Communication
for 2-Way Secure Authentication
 Optional Integrated Half-Bridge Inverter
Status & Power
Good Indicator
GPIO
Embedded
Micro
Controller
RAM
FOD
Foreign Object
Detection
Proprietary
Back Channel
Communication
High Eff. Buck
Converter
ADC
 Over Temp/Voltage/Current Protection
I2C
 I2C Interface
 6x6mm 48-TQFN Package
www.IDT.co
Modulation/
Demodulation
PAGE 3
ROM
Clock

4. IDTP9030 19V Transmitter IC
IDTP9030
 Industry’s First True Single Chip
Wireless Power Transmitter IC
Modulation/
Demodulation
High Eff. Synchronous
Half Bridge Inverter
 IDTP9030: Ultra Low BOM
2 Way Secure
Authentication
 Up to 7.5W Power Transfer
 10V - 20V Operating Voltage Range
Thermal Loop
Control
OTP, UVLO
OVP, OCP
 Advanced Foreign Object Detection (FOD)
 Proprietary Base to Mobile Communication
for 2-Way Secure Authentication
Embedded
Micro
Controller
Status & Power
Good Indicator
 Integrated Half-Bridge Inverter
RAM
GPIO
FOD
Foreign Object
Detection
Proprietary
Back Channel
Communication
High Eff. Buck
Converter
 Over Temp/Voltage/Current Protection
ADC
ROM
I2C
 I2C Interface
 6x6mm 48-TQFN Package
Clock
M ulti-Mode IDTP9030
WP C M ode
Input Range
PID
Proprietary
OFF
ON
FODs
1, 2
1, 2, 3, 4
S ecure Link
PAGE 4
10V – 20V
Authenticat ion
Back
18V – 20V
Control
Al gori thm
www.IDT.co
IDT Propriet ary Customizabl e
M ode
OFF
ON during initial verification

5. IDTP9037 - WPC ‘Qi’ Compliant
AEC-Q100 Qualified Tx
 Industry’s First True Single-Chip
WPC-Compliant
Wireless Power Transmitter IC
 AEC-Q100 Qualified
 Up to 7.5W
Transmit Power
 10V to 20V Operating Voltage
 High Total System Efficiency (~73%)
 Over Temp/Voltage/Current Protection
 6x6mm TQFN package
www.IDT.co
PAGE 5

6. Available Tx EVK Solutions
WPC 1.1, Type A5, A11
Qi Certified Design
Ultra Low BOM
Proprietary Design
WPC 1.1, Type A6
Qi Certified Design
www.IDT.co
PAGE 6

7. IDT Wireless Power Transmitter Family
IDT
Wireless Power
Solutions
Voltag
e
Coils
Supported
WPC
Complian
t
Samples/EVKs
Product Status
IDTP9030
19V
A1, A10
WPC1.0.1
Available Now
Released
IDTP9035
5V
A5, A11
WPC1.0.1
Available Now
Released
IDTP9035A
5V
A5, A11
WPC1.1
Available Now
Released
IDTP9036
12V
A6
WPC1.0.1
Available Now
Released
IDTP9036A
12V
A6
WPC1.1
Available Now
Released
IDTP9037
AECQ-100
Qualified
9V –
16V
A6
WPC1.0.1
October, 2013*
November, 2013
Transmitters
*Evaluation and development of IDTP9037 solutions
prior to Release may utilize IDTP9036A
www.IDT.co
PAGE 7

8. IDT Wireless Power Public Website
www.wirelesspowerbyidt.com
www.IDT.co
PAGE 8

9. Transcript
●
Hello, I'm Jack Deans, Field Applications Manager with Integrated Device Technology. This tech video covers IDT's current lineup of
magnetic inductive style wireless power transmitters as of July 2013. IDT designs and builds the central power controller IC. We also
design and build reference boards and evaluation kits that are certified to the current QI specification. Now, a wireless power transmitter
generates an oscillating magnetic field. A wireless power receiver recovers this energy and creates a low voltage DC current for the desired
load. In this video, we are only covering magnetic induction style wireless power transmit solutions.
●
This three coil design is our most popular design. It provides the receiver a physically larger charging area. The 9036-A is fully WPC version
1.1 compliant, which means it satisfies the new foreign object detection demands called out in that specification. The P9036 is version 1.1
compliant, but is an ideal choice for proprietary type designs that are looking for a reduced bill of materials. The WPC specification calls out
a five watt solution. If IDT's wireless power transmitter and receiver are used together, we can transmit power up to 7.5 watts, which is
above and beyond the WPC specification. Also, WPC A6 design is intended for 12-volt input voltage operation. Our solution can accept a
wider input voltage range of between nine volts and 16 volts. The P9036 and P9036-A are fully WPC FOD compliant, which require a
receiver to be used on the transmit pad to communicate power received information back to the transmitter. On top of that, IDT's devices
have an advanced foreign object detection mode, a proprietary algorithm that senses whether or not a metallic foreign object is placed on
the charger, with or without a receiver being on the transmitter. Normal wireless power communication requires a data path between the
receiver to the transmitter. This data path provides real time, load current information, as well as other command and control packets.
When the IDT transmitter is paired with the IDT receiver, our solution can provide a data path between the transmitter and the receiver in
the opposite direction as well as secure authentication.
●
The P9035 design is intended for five-volt input type applications. We offer the P9035 in an A and non-A version similar to the P9036,
where the P9035-A is fully WPC version 1.1 compliant, and the non-A version is ideal for reduced bill of materials type applications. We
support the A5 A11 coils. These designs also will work up to 7.5 watts when used with an IDT receiver. The input voltage range is not as
wide as the 9036, but it does offer the advanced foreign object detection proprietary mode and the advanced two-way communication and
secure authentication features.
●
Now the 9030 is an ultra-low bill of materials solution. It can also deliver seven and a half watts of power transfer and accept a wide input
operating voltage range as well.
●
On this slide, we show three of the available transmitter evaluation kits we have. The board on the right is the A6 design and in the center
of the circuitry is the IDT wireless power transmitter, controller IC. Closer to the coils are the pushing FETs and our controller will control
these FETs and select which coil will provide the maximum amount of efficiency and power coupling to the receiver. On the left are two
other eval kits. The top one is our A5 design. You'll notice the coil can be removed and other suppliers' coils bolted on. And below that is
the P9030 design. The components within that white silk screen outline are the only components needed to implement a wireless power
solution. This is a very low bill of materials wireless power transmit solution.
●
Here's a table listing the transmit ports we've been discussing today. They're all available now. Our roadmap includes products that have
higher integration, higher power transfer, and more safety and reliability features.
●
IDT offers comprehensive design support. We have complete reference design, application notes, as well as services such as design
reviews, Qi pre-certification testing, and even complete solution development. Please visit our website at idt.com, or go directly to our
landing page at www.wirelesspowerbyidt.com, or call an IDT salesperson for an onsite demonstration. Thank you.
www.IDT.co
PAGE 9

10. Transcript
●
Hello, I'm Jack Deans, Field Applications Manager with Integrated Device Technology. This tech video covers IDT's current lineup of
magnetic inductive style wireless power transmitters as of July 2013. IDT designs and builds the central power controller IC. We also
design and build reference boards and evaluation kits that are certified to the current QI specification. Now, a wireless power transmitter
generates an oscillating magnetic field. A wireless power receiver recovers this energy and creates a low voltage DC current for the desired
load. In this video, we are only covering magnetic induction style wireless power transmit solutions.
●
This three coil design is our most popular design. It provides the receiver a physically larger charging area. The 9036-A is fully WPC version
1.1 compliant, which means it satisfies the new foreign object detection demands called out in that specification. The P9036 is version 1.1
compliant, but is an ideal choice for proprietary type designs that are looking for a reduced bill of materials. The WPC specification calls out
a five watt solution. If IDT's wireless power transmitter and receiver are used together, we can transmit power up to 7.5 watts, which is
above and beyond the WPC specification. Also, WPC A6 design is intended for 12-volt input voltage operation. Our solution can accept a
wider input voltage range of between nine volts and 16 volts. The P9036 and P9036-A are fully WPC FOD compliant, which require a
receiver to be used on the transmit pad to communicate power received information back to the transmitter. On top of that, IDT's devices
have an advanced foreign object detection mode, a proprietary algorithm that senses whether or not a metallic foreign object is placed on
the charger, with or without a receiver being on the transmitter. Normal wireless power communication requires a data path between the
receiver to the transmitter. This data path provides real time, load current information, as well as other command and control packets.
When the IDT transmitter is paired with the IDT receiver, our solution can provide a data path between the transmitter and the receiver in
the opposite direction as well as secure authentication.
●
The P9035 design is intended for five-volt input type applications. We offer the P9035 in an A and non-A version similar to the P9036,
where the P9035-A is fully WPC version 1.1 compliant, and the non-A version is ideal for reduced bill of materials type applications. We
support the A5 A11 coils. These designs also will work up to 7.5 watts when used with an IDT receiver. The input voltage range is not as
wide as the 9036, but it does offer the advanced foreign object detection proprietary mode and the advanced two-way communication and
secure authentication features.
●
Now the 9030 is an ultra-low bill of materials solution. It can also deliver seven and a half watts of power transfer and accept a wide input
operating voltage range as well.
●
On this slide, we show three of the available transmitter evaluation kits we have. The board on the right is the A6 design and in the center
of the circuitry is the IDT wireless power transmitter, controller IC. Closer to the coils are the pushing FETs and our controller will control
these FETs and select which coil will provide the maximum amount of efficiency and power coupling to the receiver. On the left are two
other eval kits. The top one is our A5 design. You'll notice the coil can be removed and other suppliers' coils bolted on. And below that is
the P9030 design. The components within that white silk screen outline are the only components needed to implement a wireless power
solution. This is a very low bill of materials wireless power transmit solution.
●
Here's a table listing the transmit ports we've been discussing today. They're all available now. Our roadmap includes products that have
higher integration, higher power transfer, and more safety and reliability features.
●
IDT offers comprehensive design support. We have complete reference design, application notes, as well as services such as design
reviews, Qi pre-certification testing, and even complete solution development. Please visit our website at idt.com, or go directly to our
landing page at www.wirelesspowerbyidt.com, or call an IDT salesperson for an onsite demonstration. Thank you.
www.IDT.co
PAGE 9