2. Air Barrier Paper Air barrier paper is a membrane that is applied to the sheathing that serves to reduce the leakage of air between the interior and exterior of a structure. Also protects the shell from moisture during construction.
3. Attic Ventilation Attic ventilation is required to vent heat and moisture from the attic of buildings. It’s essential for proper temperature and moisture control. Four common types of ventilation include soffit vents, ridge vents, gable vents, and roof turbines.
4. Attic Ventilation: Soffit Vent An opening under the eave of a roof, used to allow air to flow into the attic or the space below the roof sheathing. Allows for the release of heat from the soffit area. This soffit vent is made from a piece of vinyl siding designed for use as a soffit vent.
5. Attic Ventilation: Ridge Vent A long, open assembly that allows air to circulate in and out of a gable roof at the ridge. Allows for the release of the buildup of heat from the underside of a gable roof.
6. Attic Ventilation: Gable Vent A screened, louvered opening in the gable that allows for heat to escape through the gable ends.
7. Attic Ventilation: Roof Turbine A turbine vent is a passive ventilation device that exhausts humid, hot air from an attic. Some forms of turbines are equipped with an electric motor.
11. Brick Arches: Centering A temporary falsework structure that is erected to serve as a guide to construction and support for the finished arch. It is removed after the arch is completed.
12. Brick Bonds: Flemish Bond A bond formed by alternating stretchers and headers in every course. Used to tie two wythes together; also for appearance value.
13. Brick Bond: Running Bond Bond made of bricks laid in an offsetting position to the course below and above it. Made entirely of stretchers.
19. Bulldozer A bulldozer is a crawler tractor equipped with a large blade used to push large quantities of soil, sand, rubble, etc., during construction work. It is used for rough grade work and land clearing.
23. Cladding: Wooden Shingle Wooden Shake- Shingles that have been split from a solid block of wood Wooden Shingle- Shingles that have been sawn from a block of wood; have even dimensions Pictured to the left are wooden shingles. Shingles
24. Code Requirements: Egress From Window The IBC for emergency exit and rescue from a window requires that the net window area when open be equal to or greater than 5.7’ sq. for second floor bedrooms and for the sill to be no more than 44” AFF. It also states that the opening area of window should be at minimum, 24” wide and 34” high. The window to the right meets the AFF requirement at 26” AFF, but fails to meet the sq. footage requirement. The opening measured 5.272 sq feet and 23” high and 33” wide.
25. Code Requirements: Residential Stairs The stairs shown to the right were measured with a tread depth of 11 1/4” while the risers were at a height of 7 ½”. The IBC states that for residential stairs the treads shall measure a minimum of 10” and the risers shall measure a maximum of 7 ¾”. These stairs DO meet the IBC.
26. Concrete Joints: Control Joint A concrete control joint is placed in concrete to keep the material from cracking during normal expansion and contraction due to temperature changes.
27. Concrete Joints: Isolation Joint Isolation joints are used to relieve flexural stresses due to vertical movement of slab-on-grade applications that adjoin fixed foundation elements such as columns, building or machinery foundations, etc. In the photo below, a concrete wall is being separated from the floor slab. Concrete Wall Concrete Slab Isolation Joint
28. Concrete Masonry Unit CMU A block made of hardened concrete. The unit has hollow cores in the inside that allow for the installation of reinforcement. CMUs allow for quick and affordable construction. Typical dimensions are 8”x8”x16”. One course of CMUs are equal to three courses of masonry brick. Brick CMUs CMUs
29. Concrete Masonry Units Non-typical CMU dimensions Photo at left: 12” block Photo at right: 4” block
33. Doors: Sidelight and Transom Transom- A small, window that is located above a door. Allows light in the structure; some have an operable transom for ventilation purposes Sidelight- A small, narrow window that is directly beside a door. It’s part of the door assembly and runs parallel to it along it’s height.
34. Electrical Components: Transformer Box A electrical transformer is used to reduce the high voltage in power transmission lines down to voltage that is suitable for use in normal applications. They can either be mounted on a pole for overhead service or in a box like this one for underground service.
35. Electrical Components: Service Head and Meter The service head is the location where the electrical service is routed from the high voltage lines down conduit and into the meter and meter box assembly. The meter is a device that measures the amount of electricity supplied to the residence. Service Head Meter
36. Electrical Components: Service Panel The location where electricity is distributed throughout the home to various circuits. Also the place where the electricity can be turned on and off.
37. Electrical Components: Duplex Receptacle A duplex receptacle is a device used to transfer the electrical current from the wiring in the walls to the walls’ surface. They make a connection point so devices can be hooked up to and removed from the electrical current with ease.
51. Front End Loader A front end loader is a piece of equipment primarily used to "load" material (asphalt, demolition debris, dirt, feed, gravel, logs, raw minerals, recycled material, rock, sand, wood chips, etc.) into or onto another type of machinery. Can also be used to dig or move fill on the jobsite.
52. Gypsum Board A construction material used for wall and ceiling coverage inside buildings. Gypsum is made using panels made of gypsum plaster pressed between two thick sheets of paper, then kiln dried. Often called sheetrock or drywall.
53. Heat Pump A heat pump is a device that uses a refrigeration cycle either to heat or cool a building by passing air or water over either the evaporating or condensing coils. The compressor/evaporator moves the coolant around through the unit to facilitate operation. The air handler moves the physical air around through the duct work and across the condenser. One advantage is the affordability of the unit to purchase and operate. The major disadvantage of the heat pump is its inability to operate well at very low temperatures and thus requiring a back-up system.
55. Insulation Insulation refers broadly to any object in a building used as insulation for any purpose. Whilst the majority of insulation in buildings is for thermal purposes, the term also applies to acoustic insulation. Its primary use is to reduce the effects of the temperature of the outside ambient air and/or the air in adjoining regions.
58. Lintel The lintel is the horizontal crosspiece over an opening, such as a door, window, carrying the weight of the masonry above it. Its used in CMU and masonry construction to span across openings. Two common lintel types are angle iron and concrete. This is an angle iron type.
59. Mortar Joints: Tooled The joint below is a tooled joint. It is vee. The joint was measured at 3/8”. Mortar type is most likely N since the brick is simply for use as a cladding on the Auburn Chemistry Building.
60. Mortar Joint: Troweled The joint below is a troweled joint. It is a flush joint. It measured at 3/8”. It is most likely type N. The brick serves as cladding on the outside of a residence.
61. Oriented Strand Board (OSB) OSB is an engineered wood panel product that is manufactured in wide mats from cross-oriented layers of thin, rectangular wooden strips compressed and bonded together with wax and resin adhesives. It is a nonveneered product.
62. Plumbing: Lavatory and Water Closet A lavatory usually is drained by 1 ½” piping while a water closet is usually drained with 3” piping. Water Closet Lavatory
64. Plumbing: Vent Plumbing Plumbing vents allow for air to enter the piping system and prevent a suction from forming in piping. It allows for free drainage. This vent was located over the kitchen, so I’m assuming that it serves to vent the sink and dishwasher drains.
66. Plywood Plywood is a type of engineered wood made from thin sheets of wood, called plies or wood veneers. The layers are glued together so that adjacent plies have their grain at right angles to each other for greater strength
67. Reinforcing Bar (Rebar) The rebar below is number 3, or 3/8”, in diameter. The indentations on the surface of the steel is to give the rebar a better bond with the concrete it’s embedded in.
68. Steep Roof Drainage: Gutter A gutter is a narrow channel which collects rainwater from the roof of a building and diverts it into a downspout.
69. Steep Roof Drainage: Downspout A vertical pipe or conduit that carries rainwater from the gutter, guttering of a building to a lower roof level, drain, ground or storm water drain.
70. Steep Roof Drainage: Splashblock A splashblock is a preformed block of concrete that is designed to divert water from the outlet of the downspout to a direction away from the foundation
71. Steep Roof Materials: Underlayment Underlayment is a layer of material that is laid between the roof coverage material and the decking to provide an additional element of moisture protection during and after construction.
73. Steep Roof Materials: Shingle Roof A shingle is a thin unit of water-resistant material nailed in an overlapping fashion with other units to provide a watertight roof covering. A wood shingle is pictured below.
74. Steep Roof Materials: Metal Panel Metal panel roofs can be made of metals such as enamel coated galvanized steel, copper, lead coated copper, stainless steel, and terne coated stainless.
84. Vapor Retarder The vapor retarder below is of the foil type. It’s placed on the side of the insulation that faces the exterior to slow the penetration of water vapor through the wall.
85. Waterproofing This waterproofing is of the roll on, cementituous type and is used to keep the water from penetrating the brick at the point where the wall intersects the ground.
86. Weep Hole A small opening that serves to drain water from the inside of or behind a particular building material or component.
87. Window: Outswinging Casement You can tell this is an outswinging casement window because it is hinged along the top and bottom and has a mechanical assembly for operation
88. Windows: Single Hung The window below is a single hung window. You can tell that it is because it has a single, operating sash.
89. Windows: Sliding The window below is a sliding window. You can tell because it has a single, operable sash that slides horizontally.
