Drilling and producing well

Drilling and Production
Lecturer: Mohd Amin Shoushtari
Office: 14-03-29
Contact: aminutp@yahoo.com

PCB 1052
INTRODUCTION TO THE OIL AND GAS INDUSTRY &
SUSTAINABLE DEVELOPMENT
DRILLING AND PRODUCING WELL

2
A production well is drilled with a
drilling rig located on the production
platform or with a rig close to
platform and production equipment.
DRILLING A WELL

3
 Well is drilled in several stages.
 Normally starts with drilling a hole of 30 to 36 inches diameters
(76 - 91 cm) down to a depth of 150 to 250 m.
 A steel pipe called casing is lowered into the well and cemented
to the wall.
 After the cement has hardened, drilling is resumed with a smaller
drill bit.
 At a certain depth the drilling is stopped and another string of
casing is set and cemented.
 This procedure will be repeated for each string until the well has
reached the depth of the reservoir.
 Number of casing strings may vary from well to well depending
on well depth and formations.
DRILLING PROCEDURE

4
Fig: Assembly of drillstring

5
Drill bit: is a cutting tool used to create cylindrical
holes. Rotary table from rotating system
will rotate the Kelly pipe, drill pipe and bit.
Rotating the bit provides an axial force to
create the hole.
Kelly: is a primary link between the drilling rig’s
surface equipment and the bit. Kellys are
manufactured with either square or
hexagonal cross-sections. API kellys come in
two standard lengths: 40 ft and 54 ft.
Drill String Components

6
Drill Pipe: is a steel pipe available in three length
ranges: Range 1 (18 to 22 ft), Range 2 (27
to 30 ft) and Range 3 (38 to 45 ft).
Range 2 is the most commonly used one.
Outside diameter (inches) Nominal weights (lb/ft)
2 7/8 10.40
3 1/2 9.50
4 14.00
4 1/2 13.75
5 16.25
5 1/2 21.90
6 5/8 25.20

7
Casing: is a steel pipe used during the drilling
of a well.
Conductor Casing ,Surface Casing,
Intermediate Casing, Production
Casing
Drill Collar: is a steel pipe thicker than drill pipe. It is
used to provide additional weight to the
bit and optimize drilling rates. Length
ranges Range 2 (30, 31 ft) and Range 3
(42, 431/2 ft).

8
CASING SIZES
 Available Casing Sizes :
36 in. OD
30 in. OD
24 in. OD, 20 in. OD
13 3/8 in. OD, 10 ¾ in. OD
9 5/8 in, OD, 7 ½ in. OD
5 ½ in. OD
4 ½ in. OD
4 in. OD
Where OD is Outside Diameter.

16
TYPES OF DRILLING RIG
For most offshore wells, the types of rig
required will fall into one of three groups
 Jack-ups – where the water depth is less than
100m
 Semi-Submersibles – in hostile waters too rough
for Drill Ship and depths over 100m
 Drill Ships – in calm waters with depths over
100m

17
Jack-up Rig

18
Jack-up Rig
 Jack-ups are used for most of the offshore exploration
drilling world-wide.
 Jack-up has a floating hull with retractable legs which can
be jacked down to the sea bed. Hull can be lifted until it is
clear off the sea surface. The legs support the hull.
 In shallow and relatively calm waters the Jack up has the
advantage of being able to leave a free standing well with
a surface completion once it is finished.

19
Semi-submersible Rig

20
Semi-submersible Rig
 Semi-Submersibles are used mostly in the range of
water depths from 100-600 m.
 This rig is not bottom-supported, but it is designed to
float and it can operate in water depths of up to 3000 ft.
 In areas where water depths exceed 100m and heavy
weather can be expected, then semi-submersibles must
be used.

21
Drill Ship

22
Drill Ship
 Drill ships are used to drill the well in deep water ( up to
7000 ft ).
 It is most suited in calmer waters and less harsh
environment.
 It can move between locations at high speed compared to
semi-submersible rigs.

24
LAND RIGS
Land rigs
Conventional rigs
Small land rigs
Medium land rigs
Large land rigs
Mobile rigs
Portable mast

25
DRILLING RIG COMPONENTS
Rotary Rig Component

26
Rotary Rig Component

27
Three systems
(1) Hoisting system
(2) Circulating system
(3) Rotary system

28
(1) Hoisting system
A large pulley system which is used to run and
pull equipment into and out of the well. Main
component is a draw-work which consists of a
clutch, gear and brake.

29
(2) Circulating system
It is a system used to circulate drilling fluid down
and up the drilling string. Main functions of the
system are
 To remove drilled cuttings from the borehole
 To exert a hydrostatic pressure to prevent
formation fluid entering the borehole.
Drilling fluid is used as a circulation fluid (water +
bentonite + weighting material + chemicals).

30
(3) Rotary system
The system is used to rotate the drilling string
and to rotate the drill bit on the bottom of the
hole.
The system includes rotary table and kelly
which is a rectangular-shaped pipe placed in
the rotary table.

32
One major component system of rotary drilling rig
To support the rotating system in „drilling the well‟ by
providing the appropriate equipment and working areas needed
for lifting, lowering and suspending the tremendous weights
Hoisting equipment used to lift, lower and suspend the drilling
stem

33
 Draw works
Overhead tools ( crown block, travelling
block, hook, elevator )
Drilling line

34
Drawworks: Specialized heavy-duty hoisting winch
Crown block: An assembly of pulleys called “sheaves”
Travelling block: An arrangement of sheaves
Hook: A large hook-shaped device
Elevators: An extremely rugged, heavy duty clamps
Drilling line: A heavy-duty wire rope

38
Components in Circulating system
1. Mud Pumps: remove large volume of
drilling fluid under high pressure
2. Shale shaker: removes drill cuttings
from the drilling fluid
3. Desander: removes granular waste from
drilling fluid
4. Desilter: removes fine particles from
drilling fluid
5. Degasser: removes entrained gases
from drilling fluid.

39
DRILLING MUD CIRCULATING SYSTEM

41
Rotary System
Drive System
Top Drive System Kelly and Rotary Drive System

42
Rotary System
Major components of rotary system –
O Rotary table with Kelly
O Top Drive System

44
DRILL BITS
Types of Drill Bits

45
DRILL BITS
Types of Drill Bits

46
DRILL BITS
Two basic categories:
1. Roller cutter bit (also known as roller cone bit)
- consists of cutting elements arranged on
cones (usually 3 cones) that rotate on bearings
about their own axis as the drill string turns the
body of the bit.

47
DRILL BITS
2. Fixed cutter bit (also known as drag bit)
- consists of stationary cutting elements and is
rotated directly by the turning of the drill string.

48
DRILLING OPERATION
DRILLING OPERATION

56
DRILLING SEQUENCE
DRILLING SEQUENCE

57
DRILLING SEQUENCE
 Typical sequence of operation
 Rig up

58
DRILLING SEQUENCE
 Typical sequence of operation
 Rig up
 Drill surface hole

59
DRILLING SEQUENCE
 Rig up
 Run & set surface casing

60
DRILLING SEQUENCE
 Rig up
 Cement surface casing

61
DRILLING SEQUENCE
 Rig up
 Drill intermediate hole

62
DRILLING SEQUENCE
 Rig up
 Run & set intermediate casing

63
DRILLING SEQUENCE
 Rig up
 Cement intermediate casing

64
DRILLING SEQUENCE
 Rig up
 Drill production hole

65
DRILLING SEQUENCE
 Rig up
 Cement production casing

66
DRILLING SEQUENCE
 Rig up

67
DRILLING SEQUENCE
 Rig up
 Run & set liner

68
DRILLING SEQUENCE
 Rig up
 Run & set liner
 Cement liner

69
 A string of tubing is set
from the producing
zones to the surface/
wellhead
 Communicate reservoir
to surface
 Provide conduit for fluid
to flow to the surface
 Control the flow of fluid
reservoir
reservoir
reservoir
reservoir

70
Requires special
wellhead and x- mas
tree arrangement
Two wells in
one Conductor

74
Christmas- tree and Wellhead

75
UNITS of Oil and Gas Flow Rate
Oil Flow Rate: bbl/day
(barrels/day)
Gas Flow Rate: MMSCFD
(Million Standard Cubic Feet/day)
1M = 1000 standard cubic feet

Drilling and producing well

Recomendados

Recomendados

Más contenido relacionado

La actualidad más candente

La actualidad más candente (20)

Destacado

Destacado (20)

Similar a Drilling and producing well

Similar a Drilling and producing well (20)

Más de Raja Rosenani

Más de Raja Rosenani (20)

Último

Último (20)

Drilling and producing well