Enviar búsqueda
Cargar
5208 chap 09
•
0 recomendaciones
•
649 vistas
saravanan A
Seguir
Good
Leer menos
Leer más
Ingeniería
Denunciar
Compartir
Denunciar
Compartir
1 de 10
Descargar ahora
Descargar para leer sin conexión
Recomendados
Nickel chrome alloys resistance to sulfuric acid
Nickel chrome alloys resistance to sulfuric acid
Heanjia Alloys
Duplex welding
Duplex welding
James Gray
Copper Strip Corrosion Test for Different Fluid Samples
Copper Strip Corrosion Test for Different Fluid Samples
IRJESJOURNAL
Copper Strip Corrossion Test in Various Aviation Fuels
Copper Strip Corrossion Test in Various Aviation Fuels
inventy
Cm33537542
Cm33537542
IJERA Editor
The effects of heat input and interpass temperature on the microstructure of ...
The effects of heat input and interpass temperature on the microstructure of ...
Mark Keeler
Corrosion behaviour of sintered 316 l austenitic stainless steel composites
Corrosion behaviour of sintered 316 l austenitic stainless steel composites
IAEME Publication
Investigation on Effect of Heat Input on Cooling Rate and Mechanical Property...
Investigation on Effect of Heat Input on Cooling Rate and Mechanical Property...
IJMER
Recomendados
Nickel chrome alloys resistance to sulfuric acid
Nickel chrome alloys resistance to sulfuric acid
Heanjia Alloys
Duplex welding
Duplex welding
James Gray
Copper Strip Corrosion Test for Different Fluid Samples
Copper Strip Corrosion Test for Different Fluid Samples
IRJESJOURNAL
Copper Strip Corrossion Test in Various Aviation Fuels
Copper Strip Corrossion Test in Various Aviation Fuels
inventy
Cm33537542
Cm33537542
IJERA Editor
The effects of heat input and interpass temperature on the microstructure of ...
The effects of heat input and interpass temperature on the microstructure of ...
Mark Keeler
Corrosion behaviour of sintered 316 l austenitic stainless steel composites
Corrosion behaviour of sintered 316 l austenitic stainless steel composites
IAEME Publication
Investigation on Effect of Heat Input on Cooling Rate and Mechanical Property...
Investigation on Effect of Heat Input on Cooling Rate and Mechanical Property...
IJMER
The Optimization of Carbonitriding Process for 1022 Self-drilling Tapping Scr...
The Optimization of Carbonitriding Process for 1022 Self-drilling Tapping Scr...
International journal of scientific and technical research in engineering (IJSTRE)
Bolelli2016
Bolelli2016
abhay shankar yadav
Synthesis And Characterization Of Al Based Metallic Foams
Synthesis And Characterization Of Al Based Metallic Foams
S_Srivatsan
121
121
vanan velu
Wj 1983 06_s147
Wj 1983 06_s147
Will Guerra
Ch 27.3 heat treatment of metals
Ch 27.3 heat treatment of metals
Nandan Choudhary
Utility Services
Utility Services
Rahul Chaurasiya
Effect of LVOF Sprayed Coating in Oxidation & Hot Corrosion Performance of Bo...
Effect of LVOF Sprayed Coating in Oxidation & Hot Corrosion Performance of Bo...
IJRES Journal
E027031034
E027031034
researchinventy
TALAT Lecture 1204: Precipitation Hardening
TALAT Lecture 1204: Precipitation Hardening
CORE-Materials
Kuprin 18.10.2017
Kuprin 18.10.2017
Ukrainian Nuclear Society
Sintering behavior of feldspar rocks
Sintering behavior of feldspar rocks
inventy
Technological characteristics of the calcined limestone
Technological characteristics of the calcined limestone
cesar hernandez
boiler fitness survey for industrial boilers
boiler fitness survey for industrial boilers
S S Ananthan Ananthan
Heat treatment 2
Heat treatment 2
senthamarai kannan
ANALYTICAL TOOL FOR ANALYSING SLAGGING CHARACTERISTIC OF HIGH ASH COALS IN UT...
ANALYTICAL TOOL FOR ANALYSING SLAGGING CHARACTERISTIC OF HIGH ASH COALS IN UT...
IAEME Publication
1.1 welding q&a for students
1.1 welding q&a for students
Suren Sirohi
Ch 27.6 cast iron (1)
Ch 27.6 cast iron (1)
Nandan Choudhary
Bme
Bme
SKIT, JAIPUR
2015 12-02-opti wind-dynamic-characterisation-gearboxes-siemens
2015 12-02-opti wind-dynamic-characterisation-gearboxes-siemens
Sirris
wind power
wind power
vijay shankari
Renewable resources
Renewable resources
SlenaCyrus
Más contenido relacionado
La actualidad más candente
The Optimization of Carbonitriding Process for 1022 Self-drilling Tapping Scr...
The Optimization of Carbonitriding Process for 1022 Self-drilling Tapping Scr...
International journal of scientific and technical research in engineering (IJSTRE)
Bolelli2016
Bolelli2016
abhay shankar yadav
Synthesis And Characterization Of Al Based Metallic Foams
Synthesis And Characterization Of Al Based Metallic Foams
S_Srivatsan
121
121
vanan velu
Wj 1983 06_s147
Wj 1983 06_s147
Will Guerra
Ch 27.3 heat treatment of metals
Ch 27.3 heat treatment of metals
Nandan Choudhary
Utility Services
Utility Services
Rahul Chaurasiya
Effect of LVOF Sprayed Coating in Oxidation & Hot Corrosion Performance of Bo...
Effect of LVOF Sprayed Coating in Oxidation & Hot Corrosion Performance of Bo...
IJRES Journal
E027031034
E027031034
researchinventy
TALAT Lecture 1204: Precipitation Hardening
TALAT Lecture 1204: Precipitation Hardening
CORE-Materials
Kuprin 18.10.2017
Kuprin 18.10.2017
Ukrainian Nuclear Society
Sintering behavior of feldspar rocks
Sintering behavior of feldspar rocks
inventy
Technological characteristics of the calcined limestone
Technological characteristics of the calcined limestone
cesar hernandez
boiler fitness survey for industrial boilers
boiler fitness survey for industrial boilers
S S Ananthan Ananthan
Heat treatment 2
Heat treatment 2
senthamarai kannan
ANALYTICAL TOOL FOR ANALYSING SLAGGING CHARACTERISTIC OF HIGH ASH COALS IN UT...
ANALYTICAL TOOL FOR ANALYSING SLAGGING CHARACTERISTIC OF HIGH ASH COALS IN UT...
IAEME Publication
1.1 welding q&a for students
1.1 welding q&a for students
Suren Sirohi
Ch 27.6 cast iron (1)
Ch 27.6 cast iron (1)
Nandan Choudhary
La actualidad más candente
(18)
The Optimization of Carbonitriding Process for 1022 Self-drilling Tapping Scr...
The Optimization of Carbonitriding Process for 1022 Self-drilling Tapping Scr...
Bolelli2016
Bolelli2016
Synthesis And Characterization Of Al Based Metallic Foams
Synthesis And Characterization Of Al Based Metallic Foams
121
121
Wj 1983 06_s147
Wj 1983 06_s147
Ch 27.3 heat treatment of metals
Ch 27.3 heat treatment of metals
Utility Services
Utility Services
Effect of LVOF Sprayed Coating in Oxidation & Hot Corrosion Performance of Bo...
Effect of LVOF Sprayed Coating in Oxidation & Hot Corrosion Performance of Bo...
E027031034
E027031034
TALAT Lecture 1204: Precipitation Hardening
TALAT Lecture 1204: Precipitation Hardening
Kuprin 18.10.2017
Kuprin 18.10.2017
Sintering behavior of feldspar rocks
Sintering behavior of feldspar rocks
Technological characteristics of the calcined limestone
Technological characteristics of the calcined limestone
boiler fitness survey for industrial boilers
boiler fitness survey for industrial boilers
Heat treatment 2
Heat treatment 2
ANALYTICAL TOOL FOR ANALYSING SLAGGING CHARACTERISTIC OF HIGH ASH COALS IN UT...
ANALYTICAL TOOL FOR ANALYSING SLAGGING CHARACTERISTIC OF HIGH ASH COALS IN UT...
1.1 welding q&a for students
1.1 welding q&a for students
Ch 27.6 cast iron (1)
Ch 27.6 cast iron (1)
Destacado
Bme
Bme
SKIT, JAIPUR
2015 12-02-opti wind-dynamic-characterisation-gearboxes-siemens
2015 12-02-opti wind-dynamic-characterisation-gearboxes-siemens
Sirris
wind power
wind power
vijay shankari
Renewable resources
Renewable resources
SlenaCyrus
FYP Report - Eoin Lees
FYP Report - Eoin Lees
Eoin Lees
Sales Presentation Show
Sales Presentation Show
RobinDavis
Wind Drivetrain: Reliability and Serviceability of Drivetrains
Wind Drivetrain: Reliability and Serviceability of Drivetrains
Torben Haagh
Abradable coatings paper
Abradable coatings paper
M. Shadab Siddiqui
letter of rec from Christian
letter of rec from Christian
Sean Fowler
JAM_RESUME
JAM_RESUME
Jose Mora
SPE 90376 presentation slides - Turbine drilling with imgregnated diamond bit...
SPE 90376 presentation slides - Turbine drilling with imgregnated diamond bit...
John Downs
NewNuclear? Global Trends in Renewable and Nuclear Power
NewNuclear? Global Trends in Renewable and Nuclear Power
Worldwatch Institute
Experimental Study of Gas Turbine Combustion with Elevated Fuel Temperatures
Experimental Study of Gas Turbine Combustion with Elevated Fuel Temperatures
Society of Women Engineers
Drilling engineering zaidi
Drilling engineering zaidi
Syed Muhammad Zaidi
Design small scale wind turbine for home electricity generation
Design small scale wind turbine for home electricity generation
Maheemal Thilakarathna
Latest Research On Gears and Bearings
Latest Research On Gears and Bearings
Navneet Roy
Wind Turbine Report Final
Wind Turbine Report Final
James Goddings
Operation and Well Setting GTI SEG-SUSC 08-10-2016
Operation and Well Setting GTI SEG-SUSC 08-10-2016
Mohamed _el_shora
Destacado
(18)
Bme
Bme
2015 12-02-opti wind-dynamic-characterisation-gearboxes-siemens
2015 12-02-opti wind-dynamic-characterisation-gearboxes-siemens
wind power
wind power
Renewable resources
Renewable resources
FYP Report - Eoin Lees
FYP Report - Eoin Lees
Sales Presentation Show
Sales Presentation Show
Wind Drivetrain: Reliability and Serviceability of Drivetrains
Wind Drivetrain: Reliability and Serviceability of Drivetrains
Abradable coatings paper
Abradable coatings paper
letter of rec from Christian
letter of rec from Christian
JAM_RESUME
JAM_RESUME
SPE 90376 presentation slides - Turbine drilling with imgregnated diamond bit...
SPE 90376 presentation slides - Turbine drilling with imgregnated diamond bit...
NewNuclear? Global Trends in Renewable and Nuclear Power
NewNuclear? Global Trends in Renewable and Nuclear Power
Experimental Study of Gas Turbine Combustion with Elevated Fuel Temperatures
Experimental Study of Gas Turbine Combustion with Elevated Fuel Temperatures
Drilling engineering zaidi
Drilling engineering zaidi
Design small scale wind turbine for home electricity generation
Design small scale wind turbine for home electricity generation
Latest Research On Gears and Bearings
Latest Research On Gears and Bearings
Wind Turbine Report Final
Wind Turbine Report Final
Operation and Well Setting GTI SEG-SUSC 08-10-2016
Operation and Well Setting GTI SEG-SUSC 08-10-2016
Similar a 5208 chap 09
hayder rashid
hayder rashid
حيدر الركابي
Copper-nickel Welding
Copper-nickel Welding
Nelson Loi
Steel Making: Lecture stainless steel Production by Electric Arc Furnace alone
Steel Making: Lecture stainless steel Production by Electric Arc Furnace alone
NED University of Engineering and Technology
JOURNAL
JOURNAL
AJITH A
Sangeeta metal-corporation
Sangeeta metal-corporation
abhishekmodak123
Performance of materials for H.E and Pressure vessel
Performance of materials for H.E and Pressure vessel
Nimit Sanandia
Cm33537542
Cm33537542
IJERA Editor
Ijmet 10 01_110
Ijmet 10 01_110
IAEME Publication
Manufacturing & Applications of Stainless Steels
Manufacturing & Applications of Stainless Steels
Venkataraman Bandaru
j.ijrmhm.2020.105280.pdf
j.ijrmhm.2020.105280.pdf
Charitha Ranwala ,CSWP
International Journal of Engineering Research and Development
International Journal of Engineering Research and Development
IJERD Editor
High-Temperature-Corrosion-Failure-of-Single-Crystal-Super-alloy-Turbine-Blades
High-Temperature-Corrosion-Failure-of-Single-Crystal-Super-alloy-Turbine-Blades
Vijay Vijayaraghavan FIEAust,CEng (UK),CPEng
Inconel 825
Inconel 825
1078S2
1st research article
1st research article
Sravani Pappu
Role of Coating in Improving High Temperature Oxidation of Steel
Role of Coating in Improving High Temperature Oxidation of Steel
IJERD Editor
Corrosion Behaviour of Friction Stir Welded Aluminium Alloys: Unpredictabilit...
Corrosion Behaviour of Friction Stir Welded Aluminium Alloys: Unpredictabilit...
CrimsonPublishersRDMS
Alloy performance-guide
Alloy performance-guide
Khin Shwe
Wear performance of ceramic cutting tool materials when cutting steel
Wear performance of ceramic cutting tool materials when cutting steel
Lepuufu
5 hot tear
5 hot tear
minnu125
4 minimum necessary preheat temperature
4 minimum necessary preheat temperature
Iyere Peter
Similar a 5208 chap 09
(20)
hayder rashid
hayder rashid
Copper-nickel Welding
Copper-nickel Welding
Steel Making: Lecture stainless steel Production by Electric Arc Furnace alone
Steel Making: Lecture stainless steel Production by Electric Arc Furnace alone
JOURNAL
JOURNAL
Sangeeta metal-corporation
Sangeeta metal-corporation
Performance of materials for H.E and Pressure vessel
Performance of materials for H.E and Pressure vessel
Cm33537542
Cm33537542
Ijmet 10 01_110
Ijmet 10 01_110
Manufacturing & Applications of Stainless Steels
Manufacturing & Applications of Stainless Steels
j.ijrmhm.2020.105280.pdf
j.ijrmhm.2020.105280.pdf
International Journal of Engineering Research and Development
International Journal of Engineering Research and Development
High-Temperature-Corrosion-Failure-of-Single-Crystal-Super-alloy-Turbine-Blades
High-Temperature-Corrosion-Failure-of-Single-Crystal-Super-alloy-Turbine-Blades
Inconel 825
Inconel 825
1st research article
1st research article
Role of Coating in Improving High Temperature Oxidation of Steel
Role of Coating in Improving High Temperature Oxidation of Steel
Corrosion Behaviour of Friction Stir Welded Aluminium Alloys: Unpredictabilit...
Corrosion Behaviour of Friction Stir Welded Aluminium Alloys: Unpredictabilit...
Alloy performance-guide
Alloy performance-guide
Wear performance of ceramic cutting tool materials when cutting steel
Wear performance of ceramic cutting tool materials when cutting steel
5 hot tear
5 hot tear
4 minimum necessary preheat temperature
4 minimum necessary preheat temperature
Último
Hospital management system project report.pdf
Hospital management system project report.pdf
Kamal Acharya
Employee leave management system project.
Employee leave management system project.
Kamal Acharya
Cara Menggugurkan Sperma Yang Masuk Rahim Biyar Tidak Hamil
Cara Menggugurkan Sperma Yang Masuk Rahim Biyar Tidak Hamil
Cara Menggugurkan Kandungan 087776558899
DeepFakes presentation : brief idea of DeepFakes
DeepFakes presentation : brief idea of DeepFakes
MayuraD1
Double Revolving field theory-how the rotor develops torque
Double Revolving field theory-how the rotor develops torque
BhangaleSonal
Unit 4_Part 1 CSE2001 Exception Handling and Function Template and Class Temp...
Unit 4_Part 1 CSE2001 Exception Handling and Function Template and Class Temp...
drmkjayanthikannan
Work-Permit-Receiver-in-Saudi-Aramco.pptx
Work-Permit-Receiver-in-Saudi-Aramco.pptx
JuliansyahHarahap1
Call Girls in South Ex (delhi) call me [🔝9953056974🔝] escort service 24X7
Call Girls in South Ex (delhi) call me [🔝9953056974🔝] escort service 24X7
9953056974 Low Rate Call Girls In Saket, Delhi NCR
Unleashing the Power of the SORA AI lastest leap
Unleashing the Power of the SORA AI lastest leap
RishantSharmaFr
DC MACHINE-Motoring and generation, Armature circuit equation
DC MACHINE-Motoring and generation, Armature circuit equation
BhangaleSonal
Orlando’s Arnold Palmer Hospital Layout Strategy-1.pptx
Orlando’s Arnold Palmer Hospital Layout Strategy-1.pptx
MuhammadAsimMuhammad6
Moment Distribution Method For Btech Civil
Moment Distribution Method For Btech Civil
VinayVitekari
PE 459 LECTURE 2- natural gas basic concepts and properties
PE 459 LECTURE 2- natural gas basic concepts and properties
sarkmank1
Design For Accessibility: Getting it right from the start
Design For Accessibility: Getting it right from the start
Quintin Balsdon
Wadi Rum luxhotel lodge Analysis case study.pptx
Wadi Rum luxhotel lodge Analysis case study.pptx
NadaHaitham1
GEAR TRAIN- BASIC CONCEPTS AND WORKING PRINCIPLE
GEAR TRAIN- BASIC CONCEPTS AND WORKING PRINCIPLE
selvakumar948
Bhubaneswar🌹Call Girls Bhubaneswar ❤Komal 9777949614 💟 Full Trusted CALL GIRL...
Bhubaneswar🌹Call Girls Bhubaneswar ❤Komal 9777949614 💟 Full Trusted CALL GIRL...
Call Girls Mumbai
Computer Lecture 01.pptxIntroduction to Computers
Computer Lecture 01.pptxIntroduction to Computers
MairaAshraf6
Online electricity billing project report..pdf
Online electricity billing project report..pdf
Kamal Acharya
School management system project Report.pdf
School management system project Report.pdf
Kamal Acharya
Último
(20)
Hospital management system project report.pdf
Hospital management system project report.pdf
Employee leave management system project.
Employee leave management system project.
Cara Menggugurkan Sperma Yang Masuk Rahim Biyar Tidak Hamil
Cara Menggugurkan Sperma Yang Masuk Rahim Biyar Tidak Hamil
DeepFakes presentation : brief idea of DeepFakes
DeepFakes presentation : brief idea of DeepFakes
Double Revolving field theory-how the rotor develops torque
Double Revolving field theory-how the rotor develops torque
Unit 4_Part 1 CSE2001 Exception Handling and Function Template and Class Temp...
Unit 4_Part 1 CSE2001 Exception Handling and Function Template and Class Temp...
Work-Permit-Receiver-in-Saudi-Aramco.pptx
Work-Permit-Receiver-in-Saudi-Aramco.pptx
Call Girls in South Ex (delhi) call me [🔝9953056974🔝] escort service 24X7
Call Girls in South Ex (delhi) call me [🔝9953056974🔝] escort service 24X7
Unleashing the Power of the SORA AI lastest leap
Unleashing the Power of the SORA AI lastest leap
DC MACHINE-Motoring and generation, Armature circuit equation
DC MACHINE-Motoring and generation, Armature circuit equation
Orlando’s Arnold Palmer Hospital Layout Strategy-1.pptx
Orlando’s Arnold Palmer Hospital Layout Strategy-1.pptx
Moment Distribution Method For Btech Civil
Moment Distribution Method For Btech Civil
PE 459 LECTURE 2- natural gas basic concepts and properties
PE 459 LECTURE 2- natural gas basic concepts and properties
Design For Accessibility: Getting it right from the start
Design For Accessibility: Getting it right from the start
Wadi Rum luxhotel lodge Analysis case study.pptx
Wadi Rum luxhotel lodge Analysis case study.pptx
GEAR TRAIN- BASIC CONCEPTS AND WORKING PRINCIPLE
GEAR TRAIN- BASIC CONCEPTS AND WORKING PRINCIPLE
Bhubaneswar🌹Call Girls Bhubaneswar ❤Komal 9777949614 💟 Full Trusted CALL GIRL...
Bhubaneswar🌹Call Girls Bhubaneswar ❤Komal 9777949614 💟 Full Trusted CALL GIRL...
Computer Lecture 01.pptxIntroduction to Computers
Computer Lecture 01.pptxIntroduction to Computers
Online electricity billing project report..pdf
Online electricity billing project report..pdf
School management system project Report.pdf
School management system project Report.pdf
5208 chap 09
1.
CHAPTER 9 Hot Corrosion
in Gas Turbines 9.1 Introduction DURING COMBUSTION in the gas turbine, sulfur from the fuel reacts with sodium chloride from ingested air at elevated temperatures to form sodium sulfate. The sodium sulfate then deposits on the hot-section components, such as nozzle guide vanes and rotor blades, resulting in accelerated oxidation (or sulfidation) attack. This is commonly referred to as “hot corrosion.” Sulfur in the fuel is generally limited to 0.3% for commercial jet engines and to 1.0% for marine gas turbines (Ref 1). Sodium chloride comes from seawater (see Table 9.1) (Ref 2). Seawater is also a source of sulfur. For aircraft engines, Tschinkel (Ref 1) suggested that runway dust may be a source of salts. Gas turbines generally use large amounts of excess air for combustion (a large fraction of air, in fact, is also used to cool the combustor), with a typical air-to-fuel ratio from about 40 to 1 (during takeoff) to 100 to 1 (at cruising speed) for aircraft gas turbine engines (Ref 2). These air-to-fuel ratios correspond to about 0.12 to 0.18 mole fractions of oxygen in the combustion zone (Ref 2). Thus, the combustion gas atmosphere is highly oxidizing. The sulfur partial pressure in the atmosphere can be extremely low, vary- ing from 10−40 to 10−26 atm over the range from 330 to 1230 °C (620 to 2240 °F) (Ref 2). These sulfur partial pressures are well below those necessary to form chromium sulfides, which are frequently observed in alloys suffering hot corrosion attack. High-temperature alloys that suffered hot corrosion attack were generally found to exhibit both oxidation and sulfidation. The hot corrosion morphology is typically characterized by a thick, porous layer of oxides with the underlying alloy matrix depleted in chromium, followed by internal chromium-rich sulfides. It is gener- ally believed that the molten sodium sulfate deposit is required to initiate hot corrosion attack. The temperature range for hot corrosion attack, although dependent on alloy composition, is generally 800 to 950 °C (1470 to 1740 °F). The lower threshold temperature is believed to be the melting temperature of the salt deposit, and the upper temperature is the salt dew point (Ref 3). This type of corrosion process is some- times referred to as Type I hot corrosion to dif- ferentiate it from Type II hot corrosion, which occurs at lower temperatures (typically 670 to 750 °C, or 1240 to 1380 °F) (Ref 4). Type II hot corrosion is characterized by pitting attack with little or no internal attack underneath the pit (Ref 4). Type II hot corrosion is rarely observed in aeroengines because the blades are generally operated at higher temperatures (Ref 5). However, marine and industrial gas turbines, which operate at lower temperatures, can experience low-temperature Type II hot corrosion. Type I hot corrosion generally proceeds in two stages: an incubation period exhibiting a low corrosion rate, followed by accelerated corrosion attack. The incubation period is related to the formation of a protective oxide scale. Initiation of accelerated corrosion attack is believed to be related to the breakdown of the protective oxide scale. Many mechanisms have been proposed to explain accelerated corrosion attack; the salt fluxing model is probably the most widely accepted. Oxides can dissolve in Na2SO4 as anionic species (basic fluxing) or cationic species (acid fluxing), depending on the salt composition (Ref 6). Salt is acidic when it is high in SO3, and basic when low in SO3. The hot corrosion Table 9.1 Composition of seawater Element Composition, ppm Chlorine 18,980 Sodium 10,561 Magnesium 1,272 Sulfur 884 Calcium 400 Potassium 380 Beryllium 65 Source: Ref 2 Name ///sr-nova/Dclabs_wip/High Temp/5208_249-258.pdf/Chap_09/ 24/10/2007 12:30PM Plate # 0 pg 249 © 2007 ASM International. All Rights Reserved. High Temperature Corrosion and Materials Application (#05208G) www.asminternational.org
2.
mechanism by salt
fluxing has been discussed in detail in Ref 7, 8, and 9. The topic of hot corrosion has been extensively covered in several reports and conference proceedings (Ref 2, 10–13). 9.2 Alloys Resistant to Hot Corrosion Various test methods have been used to study hot corrosion. Immersion testing (or crucible test- ing), which was the first laboratory test method, is not considered reliable for simulating the gas turbine environment (Ref 14, 15). The salt-coated method is quite popular in academia for studying corrosion mechanisms. Engine manufacturers, however, use the burner rig test system to deter- mine relative alloy performance ranking. The rig burns fuel with excess air to produce combustion gases with continuous injection of a synthetic sea-salt solution. This type of test system rep- resents the best laboratory apparatus for simu- lating the gas turbine environment. A special issue of High Temperature Technology published in 1989 contained a number of papers discussing burner rig test procedures (Ref 16). The data reviewed here are limited to those generated by burner rig test systems. 9.2.1 High Temperature or Type I Hot Corrosion Bergman et al. (Ref 17) studied hot corrosion resistance of various nickel- and cobalt-base alloys at temperatures from 870 to 1040 °C (1600 to 1900 °F) with 5 ppm sea-salt injection. Their results are tabulated in Table 9.2. The data show a good correlation between alloy performance and chromium content. Increasing chromium in the alloy significantly improves resistance to hot corrosion. Alloys with 15% Cr or less are very susceptible to hot corrosion attack. Cobalt-base alloys are generally better than nickel-base alloys. This may simply be due to higher chromium contents in cobalt-base alloys. One nickel-base alloy (Hastelloy X) with a chromium level similar to those of cobalt-base alloys was found to behave similarly to cobalt- base alloys. Among the alloys tested (Ref 17), alloy X-40 (Co-25Cr-10Ni-7.5W) performed best. This is in good agreement with the operating experience obtained by Royal Navy Ship (U.K.), which has demonstrated the superior hot corrosion resist- ance of alloy X-40 in a marine environment (Ref 18). Alloy X-40 was also found to be sig- nificantly better than nickel-base alloys (Ref 19), such as B-1900, U-700, U-500, and IN738 (Table 9.3). After 240 h, alloy X-40 showed hardly any corrosion attack, while alloy B-1900 (Ni-10Co-8Cr-6Mo-4.3Ta-6Al-1Ti) suffered severe attack. Alloy U-500 (Ni-18Co-19Cr- 4Mo-2.9Al-2.9Ti) and IN738 (Ni-8.5Co-16Cr- 1.7Mo-2.6W-1.7Ta-0.9Nb-3.4Al-3.4Ti) were similar, suffering only mild attack. Surprisingly, alloy U-700 (15% Cr) was found to be slightly worse than alloy B-1900 (8% Cr). Alloy B-1900 along with IN100 (10% Cr) and Nimonic 100 (11% Cr) were considered to be poor in hot corrosion and suggested that they not be considered for use without coatings, even in mildly corrosive environments (Ref 20). Burner rig tests were conducted (Ref 21) using residual oil, containing 3% S and 325 ppm Table 9.2 Results of burner rig hot corrosion tests on nickel- and cobalt-base alloys Loss in sample diameter, mm (mils) Alloy Chromium content in alloy, % 870 °C (1600 °F) 500 h 950 °C (1750 °F) 1000 h 980 °C (1800 °F) 1000 h 1040 °C (1900 °F) 1000 h SM-200 9.0 1.6 (64.4) 3.3+ (130+) … … IN100 10.0 3.3+ (130+) 3.3+ (130+) … … SEL-15 11.0 3.3+ (130+) 3.3+ (130+) … … IN713 13.0 3.3+ (130+) 2.0+ (77+) … … U-700 14.8 1.7+ (66+) 1.6 (63.9) … … SEL 15.0 1.2 (45.8) 1.3 (51.8) 0.3 (11.4) … U-500 18.5 0.2 (7.6) 0.8 (31.7) 0.7 (29.3) … Rene 41 19.0 0.3 (10.3) … 0.8 (30.8) Hastelloy alloy X 22.0 … 0.3 (12.0) 0.4 (15.2) … L-605 (alloy 25) 20.0 … 0.4 (15.3) 0.3 (11.3) 1.1 (41.9) WI-52 21.0 0.5 (21.4) 0.5 (18.2) … 1.9 (73.9) MM-509 21.5 … 0.3 (10.9) … 0.8 (31.8) SM-302 21.5 0.14 (5.4) 0.3 (10.0) … 0.6 (23.1) X-40 25.0 0.11 (4.2) 0.3 (11.6) … 0.5 (18.5) Note: 5 ppm sea salt injection. Source: Ref 17 250 / High Temperature Corrosion and Materials Applications Name ///sr-nova/Dclabs_wip/High Temp/5208_249-258.pdf/Chap_09/ 24/10/2007 12:30PM Plate # 0 pg 250 © 2007 ASM International. All Rights Reserved. High Temperature Corrosion and Materials Application (#05208G) www.asminternational.org
3.
NaCl (equivalent to
5 ppm NaCl in air), at 870 °C (1600 °F) for 600 h on several cobalt- base alloys, which were X-45 (Co-25Cr-10Ni- 7.5W), MAR-M302 (Co-21.5Cr-10W-9Ta-0.2Zr), MAR-M509 (Co-21.5Cr-10Ni-7W-3.5Ta-0.2T- 0.5Zr), S-816 (Co-20Cr-20Ni-4W-4Nb-4Mo), FSX-418 (Co-30Cr-10Ni-7W-0.15Y), and FSX- 414 (Co-30Cr-10Ni-7W). The test results are shown in Fig. 9.1. All six cobalt-base alloys with chromium varying from 20 to 30% suffered little corrosion attack (about 0.04 to 0.12 mm, or 0.002 to 0.005 in., or 2 to 5 mils). Under the same test condition, Udimet 700 (Ni-15Cr- 18.5Co-5.2Mo-5.3Al-3.5T) suffered about 0.76 mm (0.03 in., or 30 mils) of attack (Ref 21). Figure 9.2 summarizes the data for a group of nickel- and cobalt-base alloys at 870 to 1040 °C (1600 to 1900 °F) (Ref 22). Alloy U-700 was found to be inferior to IN713 at 950 °C (1750 °F). This was contrary to field experience. Alloy U-700 has served most reliably in aircraft jet engines, whereas IN713 has suffered severe hot corrosion in many applications (Ref 22). The authors attributed the high corrosion rate of alloy U-700 to the low chromium content in this heat (i.e., 13.6% versus 15.0% for regular heats). A systematic study was conducted (Ref 22) to determine the effects of alloying elements on hot corrosion resistance. In the Ni-10Co-15Cr- 4Al-2Ti system, decreasing chromium from 25 to 10% resulted in increases in hot corrosion attack (Fig. 9.3). The data also suggest that decreasing aluminum while increasing titanium improves hot corrosion resistance. Furthermore, addition of 8% W to Ni-10Co-15Cr-4Al-2Ti alloy resulted in no apparent change in hot corrosion resistance. In binary and ternary alloy systems of nickel- and cobalt-base alloys, these authors further observed the effectiveness of chromium in improving hot corrosion resistance at 910, 950, and 1040 °C (1675, 1750, and 1900 °F) (Ref 22). Results are shown in Fig. 9.4. In examining the effect of the third alloying element in Ni-Cr alloys, they found that (Ref 22): Tungsten (8%) showed little effect at 910 and 950 °C (1675 and 1750 °F), but a slightly detrimental effect at 1040 °C (1900 °F). Cobalt was only slightly beneficial. Molybdenum was detrimental at 1040 °C (1900 °F), but had little effect at lower tem- peratures. Titanium (5%) showed significant improve- ment at 1040 °C (1900 °F), but little effect at lower temperatures. Aluminum (8%) was detrimental, causing severe hot corrosion attack at 1040 °C (1900 °F). For Co-25Cr alloys, the effect of the third alloying element was summarized as (Ref 22): Tungsten (8%) was detrimental at 1040 °C (1900 °F), with little effect at lower tem- peratures. ATTACK, mm per side 0 0.04 0.08 0.12 6543210 ATTACK, mils per side Surface loss Maximum penetration FSX–414 FSX–418 S–816 MAR–M 509 MAR–M 302 X–45 Fig. 9.1 Relative hot corrosion resistance of cobalt-base alloys obtained from burner rig tests using 3% S residual oil and 325 ppm NaCl in fuel (equivalent to 5 ppm NaCl in air) at 870 °C (1600 °F) for 600 h. Source: Beltran (Ref 21) Table 9.3 Results of burner rig tests at 874 °C (1605 °F) for nickel- and cobalt-base alloys Penetration depth, mm/1000 h (mils/1000 h) Exposure time, h B-1900 U-700 U-500 IN738 X-40 100 2.8 (111) … … … … 170 2.5 (97) 3.3 (129) 0.7 (29) … … 240 2.1 (83) … 0.5 (20) 0.9 (35) Slight Note: Diesel fuel containing 1.0% S, 125 ppm Na, 15 ppm Mg, 4.8 ppm Ca, 4.1 ppm K, and 225 ppm Cl, air-to-fuel ratio was 50 : 1, and 100 h cycle. Source: Ref 19 Chapter 9: Hot Corrosion in Gas Turbines / 251 Name ///sr-nova/Dclabs_wip/High Temp/5208_249-258.pdf/Chap_09/ 24/10/2007 12:30PM Plate # 0 pg 251 © 2007 ASM International. All Rights Reserved. High Temperature Corrosion and Materials Application (#05208G) www.asminternational.org
4.
Molybdenum (6%) was
detrimental at 950 and 1040 °C (1750 and 1900 °F), with little effect at 910 °C (1675 °F). Tantalum (7%) and nickel (10%) showed little effect. Burner rig tests were conducted (Ref 23) at 900 °C (1650 °F) on several wrought super- alloys and nickel aluminides. The combustion gas stream was generated by using No. 2 fuel oil containing about 0.4 wt% S with an air-to-fuel ratio of 35 to 1 and injection of either 5 or 50 ppm sea salt into the combustion gas stream. The specimens were loaded in a carousel, that rotated at 30 rpm during testing to ensure that all the specimens were subjected to the same test con- dition. The specimens were cycled out of the combustion gas stream once every hour for 2 min, during which time the specimens were cooled by forced air (fan cool) to less than 205 °C (400 °F). Superalloys tested were alloy X (Ni-22Cr-18.5Fe-9Mo-0.5W), alloy S (Ni-15.5Cr-14.5Mo-0.05La), alloy 230 (Ni-22Cr- 14W-2Mo-0.02La), alloy 625 (Ni-21.5Cr-9Mo- 3.6Nb), alloy 188 (Co-22Cr-22Ni-14W-0.04La), alloy 25 (Co-20Cr-10Ni-15W), and alloy 150 (Co-27Cr-18Fe). Two nickel aluminides, IC-50 (Ni-11.3Al-0.6Zr-0.02B) and IC-218 Surface loss Maximum penetration 1600 °F (870 °C) 1750 °F (950 °C) 1900 °F (1040 °C) SL- Surface loss MP- Maximum penetration Alloy U–700 SM–200 SEL IN713 U–500 X WI–52 SM–302 X–45 0 10 (250) (500) (750) (1000) (1250) (1500) (1750) 20 30 40 50 60 70 Loss in diameter, mils (µm) 109.2 75.6 SL 92.4 MP 80.2 Fig. 9.2 Relative hot corrosion resistance of nickel- and cobalt-base alloys obtained from burner rig tests at 870, 950, and 1040 °C (1600, 1750, and 1900 °F) for 100 h, using 1% S diesel fuel, 30:1 air-to-fuel ratio, and 200 ppm sea-salt injection. Source: Bergman et al. (Ref 22) 252 / High Temperature Corrosion and Materials Applications Name ///sr-nova/Dclabs_wip/High Temp/5208_249-258.pdf/Chap_09/ 24/10/2007 12:30PM Plate # 0 pg 252 © 2007 ASM International. All Rights Reserved. High Temperature Corrosion and Materials Application (#05208G) www.asminternational.org
5.
(Ni-7.8Cr-8.5Al-0.8Zr-0.02B), which were developed
by Oak Ridge National Laboratory, were included in the test program. The results of tests at 900 °C (1650 °F) for 200 h with 50 ppm sea salt are summarized in Table 9.4 (Ref 23). Both IC-50 and IC-218 nickel aluminides suffered severe hot corrosion attack after 200 h at 900 °C (1650 °F) with 50 ppm sea salt being injected into the combustion gas stream. Scanning electron microscopy with energy-dispersive x-ray spectroscopy (SEM/ EDX) analysis showed that both nickel alumi- nides exhibited porous nickel or nickel-rich oxides with nickel sulfide penetrating through the remaining metal (Ref 23). Figure 9.5 shows the cross section of a corroded IC-218 specimen after hot corrosion burner rig testing at 900 °C (1650 °F) for 200 h with 50 ppm sea salt, re- vealing the formation of nickel oxides and nickel sulfides. SEM/EDX analysis showed that a thin, protective chromium-rich oxide scale formed on alloys X, 230, and 188. Alloy 25, although exhibiting little weight change (Table 9.4), showed evidence of initial breakdown of the chromium-rich oxide scale. SEM/EDX analysis revealed the formation of cobalt-rich oxide nodules on the outer oxide scale on alloy 25. This indicated the initiation of the breakaway corrosion for alloy 25 after 200 h at 900 °C (1650 °F) with 50 ppm sea salt. Long- term test results under the same test condition clearly showed that alloy 25 suffered severe hot corrosion in excess of 200 h of testing, as shown in Fig. 9.6 (Ref 23). Alloy 140 0 250 500 750 1000 1250 1500 1750 2000 Loss in diameters, µm 0 10 20 30 40 50 60 70 80 Loss in diameters, mils Ni-10Co-0.5Nb-4Al-2Ti-25Cr TEL-1 Ni-10Co-0.5Nb-4Al-2Ti-20Cr TEL-2 Ni-10Co-0.5Nb-4Al-2Ti-15Cr TEL-3 Ni-10Co-0.5Nb-4Al-2Ti-10Cr TEL-4 Ni-10Co-0.5Nb-6Al-0Ti-15Cr TEL-5 Ni-10Co-0.5Nb-5Al-3Ti-15Cr TEL-6 Ni-10Co-0.5Nb-2Al-4Ti-15Cr TEL-7 Ni-10Co-0.5Nb-8W-4Ai-2Ti-15Cr TEL-8 Ni-10Co-0.5Nb-4Mo-15Cr TEL-9 Ni-0Co-0.5Nb-2Mo-4W-15Cr TEL-10 Ni-25Co-0.5Nb-15Cr TEL-11 Ni-0Co-0.5Nb-6Al-4Ti-15Cr TEL-12 Ni-15Co-4Mo-3.7Al-1.8Ti-19 Cr MELINI-1 Ni-15Co-3.5Al-1.8Ti-4.5 Re-19Cr MELINI-2 Ni-16Co-3.6Al-2.1Ti-21Cr MELINI-3 Ni-15Co-4Mo-2.9Al-1.8Ti-0.2Y-19Cr MELNI-4 Ni-25Co-4Mo-3.5Al-2.2Ti-0.2Y-19Cr MELNI-5 Ni-15Co-4Mo-3.7Al-1.8Ti-0.08Y-19Cr MELNI-6 Maximum penetration Surface loss 950 °C (1750 °F) 1040 °C (1900 °F) Fig. 9.3 Relative hot corrosion resistance of experimental alloys obtained from burner rig tests at 950 and 1040 °C (1750 and 1900 °F) for 100 h, using 1% S diesel fuel, 30:1 air-to-fuel ratio, and 200 ppm sea-salt injection. Source: Bergman et al. (Ref 22) Chapter 9: Hot Corrosion in Gas Turbines / 253 Name ///sr-nova/Dclabs_wip/High Temp/5208_249-258.pdf/Chap_09/ 24/10/2007 12:30PM Plate # 0 pg 253 © 2007 ASM International. All Rights Reserved. High Temperature Corrosion and Materials Application (#05208G) www.asminternational.org
6.
Figure 9.6 also
shows alloys 230 and 188 exhibiting very little weight change for exposure time up to 1000 h. The results of the 1000 h tests are summarized in Table 9.5 (Ref 23). Three nickel-base alloys (alloys S, X, and 625) and one cobalt-base alloy (alloy 25) were completely corroded before the test reached 1000 h, while nickel-base alloy 230 and cobalt-base alloys 150 and 188 exhibited little corrosion attack after 1000 h. Under the same test conditions in the same burner rig, nickel-base alloy HR-160 with 29% Co, 28% Cr and 2.75% Si was found to perform as well as alloys 230, 150, and 188. Figure 9.7 shows the conditions of the test spe- cimens comparing HR-160 with other wrought alloys (Ref 24). Another burner rig test was conducted (Ref 23) with 5 ppm sea salt at 900 °C (1650 °F) under the same combustion conditions (i.e., No. 2 fuel oil with 0.4% S and 35-to-1 air- to-fuel ratio). The results are summarized in Table 9.6. Even at this low level of sea salt (5 ppm) in the combustion gas stream, cobalt- base alloy 25 continued to exhibit very poor hot corrosion resistance compared with some nickel- base alloys. 9.2.2 Low-Temperature or Type II Hot Corrosion “Low-temperature” or Type II hot corrosion has been observed at temperatures lower than the temperature range where Type I hot corrosion has been encountered. Severe hot corrosion of alloy S590 and Nimonic 80A after several thousand hours of operation in a gas turbine that burned blast-furnace gas with the 700 to 730 °C (1290 to 1345 °F) turbine entry temperature was reported in Ref 25. In 1976, a new form of hot corrosion attack of gas turbine airfoil materials in a marine gas turbine was reported (Ref 26). The first-stage turbine blades coated with a CoCrAlY coating, which had exhibited satis- factory hot corrosion resistance for metal tem- peratures in the range 800 to 1000 °C (1470 to 1830 °F), were found to suffer corrosion attack for metal temperatures at about 600 to 730 °C (1110 to 1345 °F) (Ref 26). The corrosion Maximum penetration measurements CP-Complete penetration through the specimen 1675 °F (910 °C) 1750 °F (950 °C) 1900 °F (1040 °C) Alloy RL-1 RL-2 RL-3 RL-4 RL-5 RL-6 RL-7 RL-8 RL-9 RL-10 RL-11 RL-12 RL-13 RL-14 RL-15 0 10 (250) 20 30 40 50 60 70 (500) (750) (1000) (1250) (1500) (1750) Loss in diameter, mils (µm) UNALLOYED NICKEL Ni-10Cr Ni-15Cr Ni-25Cr Ni-15Cr-8W Ni-15Cr-24Co Ni-15Cr-6Mo Ni-15Cr-5Ti Ni-15Cr-8Al UNALLOYED COBALT Co-25Cr Co-25Cr-8W Co-25Cr-6Mo Co-25Cr-7Ta Co-25Cr-10Ni 130CP 130CP 90 130CP 130CP } } Fig. 9.4 Relative hot corrosion resistance of experimental alloys obtained from burner rig tests at 910, 950, and 1040 °C (1675, 1750, and 1900 °F) for 100 h, using 1% S diesel fuel, 30:1 air-to-fuel ratio, and 200 ppm sea salt injection. Source: Bergman et al. (Ref 22) Table 9.4 Results of burner rig hot corrosion tests at 900 °C (1650 °F) for 200 h with 50 ppm sea salt with specimens being cycled once every hour Alloy Weight change, mg/cm2 Metal loss, mm (mils) Total depth of attack(a), mm (mils) X −0.76 0.02 (0.6) 0.07 (2.8) 230 −1.35 0.02 (0.8) 0.06 (2.4) 25 −1.62 0.02 (0.9) 0.07 (2.8) 188 0.93 0.02 (0.7) 0.04 (1.6) IC-50 72 0.72 (28.3), completely corroded 0.72 (28.3), completely corroded IC-218 83 0.75 (29.5), completely corroded 0.75 (29.5), completely corroded (a) Metal loss + internal penetration. Source: Ref 23 254 / High Temperature Corrosion and Materials Applications Name ///sr-nova/Dclabs_wip/High Temp/5208_249-258.pdf/Chap_09/ 24/10/2007 12:30PM Plate # 0 pg 254 © 2007 ASM International. All Rights Reserved. High Temperature Corrosion and Materials Application (#05208G) www.asminternational.org
7.
products formed on
the CoCrAlY coating were found to contain CoSO4 and NiSO4 (Ref 26). It was proposed (Ref 27) that the mechanism of low-temperature hot corrosion attack of a CoCrAlY coating involved the formation of the low melting Na2SO4-CoSO4 eutectic (melting point of 565 °C, or 1045 °F). Nickel-base alloys were, in general, more resistant to Type II hot corrosion than cobalt-base alloys as found in Ref 28. It was also found (Ref 29) that NiCrAlY and NiCoCrAlY coatings were, in general, more resistant than CoCrAlY coatings. Increases in chromium content in superalloys and coatings provided significant increases in low-temperature hot corrosion resistance (750 °C, or 1380 °F) for these materials (Ref 30). Both IN939 (23% Cr) and NiCrAlY coating (39% Cr) were found to exhibit good low-temperature hot corrosion resistance. NiCrAlY coatings with 26, 34, and 42% Cr were tested and found significant resistance to low- temperature hot corrosion for coatings with only 34 and 42% Cr (Ref 31). MCrAlY coatings (M = Co and/or Ni) with 30 to 35% Cr were tested (Ref 32). All of the coatings showed improved resistance to low-temperature hot corrosion (705 °C, or 1300 °F) compared with CoCrAlY coating with about 20% Cr. A critical chromium content of no less than 37% was required for cobalt-base coatings to provide resistance to both low- and high-temperature hot corrosion (Ref 33). 9.3 Summary High-temperature or Type I hot corrosion generally occurs in the temperature range of 800 to 950 °C (1470 to 1740 °F). It is believed that the molten sodium sulfate deposit is re- quired to initiate hot corrosion attack. The Type I hot corrosion morphology is typically charac- terized by a thick, porous layer of oxides with the underlying alloy matrix depleted in chromium, followed by internal chromium-rich sulfides. Low-temperature or Type II hot corrosion gen- erally occurs in the temperature range of 670 to 750 °C (1238 to 1382 °F). Type II hot corro- sion is characterized by pitting attack with little or no internal attack underneath the pit. Cobalt-base alloys are more susceptible to Type II hot corrosion, which generally involves 100 µm 5 4 1 2 3 Fig. 9.5 Scanning electron backscattered image showing the cross section of a corroded IC-218 nickel aluminide specimen after hot corrosion burner rig testing at 900 °C (1650 °F) for 200 h with 50 ppm sea salt using No. 2 fuel oil (0.4% S) for combustion at 35:1 air-to-fuel ratio. The results (wt%) of EDX analysis are: 1: 100% Ni; 2: 74% Ni, 26% S; 3: 100% Ni; 4: 88% Ni, 8% Cr, 4% Al; and 5: 98% Ni, 2% Al. Areas 1, 4, and 5 were essentially nickel oxides, area 2 was nickel sulfide, and area 3 was pure nickel. Courtesy of Haynes International, Inc. Chapter 9: Hot Corrosion in Gas Turbines / 255 Name ///sr-nova/Dclabs_wip/High Temp/5208_249-258.pdf/Chap_09/ 24/10/2007 12:30PM Plate # 0 pg 255 © 2007 ASM International. All Rights Reserved. High Temperature Corrosion and Materials Application (#05208G) www.asminternational.org
8.
Na2SO4 and CoSO4.
Increasing chromium in alloys or coatings will improve the resistance of the material to both Type I and Type II hot corrosion attack. REFERENCES 1. J.G. Tschinkel, Corrosion, Vol 28 (No. 5), 1972, p 161 2. J. Stringer, “Hot Corrosion in Gas Tur- bines,” Report MCIC-72-08, Battelle Columbus Laboratories, Columbus, OH, 1972 3. J. Stringer, High Temperature Corrosion in Energy Systems, M.F. Rothman, Ed., The Metallurgical Society of AIME, 1985, p 3 4. J. Stringer, Coatings in the Electricity Sup- ply Industry: Past, Present, and Opportu- nities for the Future, Surf. Coat. Technol., Vol 108/109, 1998, p 1 5. A.K. Koul, J.P. Immarigeon, R.V. Dainty, and P.C. Patnaik, Degradation of High Per- formance Aero-Engine Turbine Blades, Advanced Materials and Coatings for Combustion Turbines, V.P. Swaminathan and N.S. Cheruvu, Ed., ASM International, 1994, p 69 6. G.H. Meier, High Temperature Corrosion 2 —Advanced Materials and Coatings (Les Embiez, France), May 22–26, 1989, Else- vier Science, 1989, p 1 7. J.A. Goebel, F.S. Pettit, and G.W. Goward, Metall. Trans., Vol 4, 1973, p 261 8. J. Stringer, Am. Rev. Mater. Sci., Vol 7, 1977, p 477 9. R.A. Rapp, Corrosion, Vol 42 (No. 10), 1986, p 568 10. J. Stringer, R.I. Jaffee, and T.F. Kearns, Ed., High Temperature Corrosion of Aerospace Alloys, Advisory Group for Aerospace Research and Development, North Atlantic Treaty Organizations, AGARD-CP-120, Harford House, London, 1973 11. J.W. Fairbanks and I. Machlin, Ed., Proc. 1974 Gas Turbine Materials in The Marine Environment Conf., MCIC-75-27, Battelle Columbus Laboratories, 1974 12. Hot Corrosion Problems Associated with Gas Turbines, STP 421, ASTM, 1967 13. A.B. Hart and A.J.B. Cutler, Ed., Deposition and Corrosion in Gas Turbines, Applied Science, London, 1973 14. J.F.G. Conde and G.C. Booth, Deposition and Corrosion in Gas Turbines, A.B. Hart and A.J.B. Cutler, Ed., John Wiley Sons, 1973, p 278 Haynes alloy 230 Haynes alloy 188 Haynes alloy 25 20 10 0 –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 –110 –120 –130 –140 –150 –160 –170 –180 0 100 200 300 400 500 600 700 800 9001000 Exposure time, h Weightchange,mg/cm2 Fig. 9.6 Results of burner rig tests at 900 °C (1650 °F) with 50 ppm sea salt using No. 2 fuel oil (0.4% S) for combustion at 35:1 air-to-fuel ratio for alloys 230, 188, and 25. Source: Lai et al. (Ref 23) Table 9.5 Results of burner rig hot corrosion tests at 900 °C (1650 °F) for 1000 h with 50 ppm sea salt with specimens being cycled once every hour Alloy Weight change, mg/cm2 Total depth of attack(a), mm (mils) S … Completely corroded in 350 h (1.3 mm, or 49.2 mil thick specimen) X … Completely corroded in 500 h (1.2 mm, or 45.9 mil thick specimen) 625 … Completely corroded in 940 h (1.6 mm, or 63.7 mil thick specimen) 230 11.5 0.11 (4.4) 25 … Completely corroded in 476 h (1.0 mm, or 37.8 mil thick specimen) 150 10.0 0.13 (5.2) 188 9.9 0.08 (3.2) (a) Metal loss + internal penetration. Source: Ref 23 256 / High Temperature Corrosion and Materials Applications Name ///sr-nova/Dclabs_wip/High Temp/5208_249-258.pdf/Chap_09/ 24/10/2007 12:30PM Plate # 0 pg 256 © 2007 ASM International. All Rights Reserved. High Temperature Corrosion and Materials Application (#05208G) www.asminternational.org
9.
15. M.J. Donachie,
R.A. Sprague, R.N. Russell, K.G. Boll, and E.F. Bradley, Hot Corrosion Problems Associated with Gas Turbines, STP 421, ASTM, 1967, p 85 16. High Temperature Technology, Special Issue on Hot-Salt Corrosion Standards Test Pro- cedures and Performance, Vol 7 (No. 4), Nov 1989 17. P.A. Bergman, A.M. Beltran, and C.T. Sims, Development of Hot Corrosion-Resistant Alloys for Marine Gas Turbine Service, Final Summary Report to Marine Engi- neering Lab., Contract N600 (61533) 65661, Navy Ship RD Center, Annapolis, MD, Oct 1, 1967 18. J. Clelland, A.F. Taylor, and L. Wortley, Proc. 1974 Gas Turbine Materials in the Marine Environment Conf., MCIC-75-27, J.W. Fairbanks and I. Machlin, Ed., Battelle Columbus Laboratories, 1974, p 397 19. M.J. Zetlmeisl, D.F. Laurence, and K.J. McCarthy, Mater. Perform., June 1984, p 41 20. J. Stringer, Proc. Symp. Properties of High Temperature Alloys with Emphasis on Environmental Effects, Z.A. Foroulis and F.S. Pettit, Ed., The Electrochemical Society, 1976, p 513 21. A.M. Beltran, Cobalt, Vol 46, 1970, p 3 22. P.A. Bergman, C.T. Sims, and A.M. Beltran, Hot Corrosion Problems Associated with Gas Turbines, STP 421, ASTM, 1967, p 38 23. G.Y. Lai, J.J. Barnes, and J.E. Barnes, “A Burner Rig Investigation of the Hot Corro- sion Behavior of Several Wrought Super- alloys and Intermetallics,” Paper 91-GT-21, International Gas Turbine and Aeroengine Congress and Exposition (Orlando, FL), June 3–6, 1991 24. “Haynes HR-160 Alloy,” H-3129A, Haynes International, Inc., Kokomo, IN 25. W. Moller, Deposition and Corrosion in Gas Turbines, A.B. Hart and A.J.B. Cutler, Ed., John Wiley and Sons, 1973, p 1 26. D.J. Wortman, R.E. Fryxell, and I.I. Bessen, ATheory for Accelerated Turbine Corrosion at Intermediate Temperatures, Proc. Third Conference on Gas Turbine Materials in a Marine Environment, Session V, Paper 11 (Bath, England), 1976 27. K.L. Luthra, Metall. Trans. A, Vol 13, 1982, p 1853 28. D.J. Wortman, R.E. Fryxell, K.L. Luthra, and P.A. Bergman, Proc. Fourth US/UK Conf. on Gas Turbine Materials in a Marine 310SS RA330 alloy Alloy 800H Alloy 625 HR160® alloy 1000 h 476 h 1000 h 940 h 1000 h Fig. 9.7 Test specimens alloy HR-160, 625, 800H, RA330, and Type 310 at 900 °C (1650 °F) in the combustion gas stream generated by a burner rig using No. 2 fuel oil (0.4% S) for combustion at 35:1 air-to-fuel ratio and with injection of 50 ppm sea salt into the combustion gas stream. During testing, specimens were cycled once every hour. Source: Ref 24 Table 9.6 Results of burner rig hot corrosion tests at 900 °C (1650 °F) for 1000 h with 5 ppm sea salt with specimens being cycled once every hour Alloy Weight change, mg/cm2 Metal loss, mm (mils) Total depth of attack(a), mm (mils) X −0.24 0.04 (1.6) 0.14 (5.5) 230 −0.79 0.03 (1.2) 0.13 (5.1) 625 5.87 0.05 (1.9) 0.14 (5.3) 25 … … Completely corroded (1.09 mm, or 43 mils) 188 1.09 0.02 (0.8) 0.07 (2.8) (a) Metal loss + internal penetration. Source: Ref 23 Chapter 9: Hot Corrosion in Gas Turbines / 257 Name ///sr-nova/Dclabs_wip/High Temp/5208_249-258.pdf/Chap_09/ 24/10/2007 12:30PM Plate # 0 pg 257 © 2007 ASM International. All Rights Reserved. High Temperature Corrosion and Materials Application (#05208G) www.asminternational.org
10.
Environment (Annapolis, MD),
U.S. Naval Academy, 1979, p 317 29. L.F. Aprigliano, Proc. Fourth US/UK Conf. on Gas Turbine Materials in a Marine Environment (Annapolis, MD), U.S. Naval Academy, 1979, p 151 30. A.R. Taylor, B.A. Wareham, G.C. Booth, and J.F. Conde, Low and High Pressure Rig Evaluation of Materials and Coatings, Proc. Third Conference on Gas Turbine Materials in a Marine Environment, Session III, Paper No. 3 (Bath, England), 1976 31. J.F.G. Conde, G.C. Booth, A.F. Taylor, and C.G. McGreath, Hot Corrosion in Marine Gas Turbines, Proc. Conf. High Tem- perature Alloys for Gas Turbines, COST 50, 1982, p 237 32. J.A. Goebel, Advanced Coating Develop- ment for Industrial/Utility Gas Turbine Engines, Proc. First Conf. on Advanced Materials for Alternative Fuel Capable Directly Fired Heat Engines (Castine, ME), Department of Energy–Electric Power Research Institute, 1979, p 473 33. K.L. Luthra and J.H. Wood, High Chro- mium Cobalt-Base Coatings for Low Tem- perature Hot Corrosion, Thin Solid Films, Vol 119, 1984, p 271 258 / High Temperature Corrosion and Materials Applications Name ///sr-nova/Dclabs_wip/High Temp/5208_249-258.pdf/Chap_09/ 24/10/2007 12:30PM Plate # 0 pg 258 © 2007 ASM International. All Rights Reserved. High Temperature Corrosion and Materials Application (#05208G) www.asminternational.org
Descargar ahora