2. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
Steps to create true nano-particle colloidal silver:
1. Fill a glass or ceramic container with distilled water. Do not use
tap or filtered water.
2. Place two clean and shiny silver rods in the water. They must be
more than one inch apart and larger than 14 AWG in thickness – 9
AWG is ideal because the surface area is greater.
3. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
The rods should be at least 99.99% pure silver.
4. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
3. Making Connection
5. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
4. Launch Spooky2 and use the calculator to estimate the Dwell
you need to enter for the Colloidal Silver Generation program.
You may have to go to step 5 and briefly run the generator to
measure the Current (mA) with a multimeter so you can enter it
in the calculator.
The four fields under By Calculation are interactive. Changing a
value in one will alter the values in the others. Enter your
numbers in the top three to find the Dwell Multiplier you need to
enter in the Program Options pane.
6. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
The total time needed to make your CS will be shown beside Duration.
The two fields under By Measurement are not interactive. Enter the
TDS of your distilled water before you start, then the TDS of the final
product (or during production). The Estimated PPM will be shown
beneath.
Note that a TDS (Total Dissolved Solids) meter will NOT measure the
colloidal silver content of a solution. Colloids are not dissolved solids.
7. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
8. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
If you don't have a multimeter to measure the current, simply make
the supposition that your system will consume 0.2 mA. This is a very
rough average estimate that assumes you have two 9 AWG rods
one inch apart submerged to a depth of 12 inches in distilled water.
9. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
5. Load the JW-Colloidal Silver Generation Preset and the
Colloidal Silver waveform. Enter the estimated dwell into the
Dwell Multiplier field and start the Channel. The waveform has
been designed to produce very small silver particles of
varying size. Do not rush the manufacturing process. Slower
is better. Now start your Channel.
10. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
11. Official Support Website: www.spooky2.com
Official Purchasing Website: www.spooky2-mall.com
Email:echolee@cleanenergy-npt.com
or service@spooky2.com
Thank you!