This document discusses transmission line theory and analysis. It begins by explaining how power is delivered through wires at low frequencies versus through electric and magnetic fields at microwave frequencies, defining transmission lines. It then lists common types of transmission lines including two-wire, coaxial cable, waveguide, and planar lines. It analyzes the differences between analyzing circuits at low versus high frequencies. Finally, it provides details on metallic cable transmission media, including balanced vs unbalanced lines, equivalent circuits, wave propagation, losses, phasors, and characteristic impedance.
A CASE STUDY ON CERAMIC INDUSTRY OF BANGLADESH.pptx
transmission-lines
1. 1
Transmission Line TheoryTransmission Line Theory
In an electronic system, the delivery ofIn an electronic system, the delivery of
power requires the connection of two wirespower requires the connection of two wires
between the source and the load. At lowbetween the source and the load. At low
frequencies, power is considered to be deliveredfrequencies, power is considered to be delivered
to the load through the wire.to the load through the wire.
In the microwave frequency region, powerIn the microwave frequency region, power
is considered to be in electric and magneticis considered to be in electric and magnetic
fields that are guided from lace to place by somefields that are guided from lace to place by some
physical structure. Any physical structure thatphysical structure. Any physical structure that
will guide an electromagnetic wave place towill guide an electromagnetic wave place to
place is called aplace is called a Transmission LineTransmission Line..
2. 2
Types of Transmission LinesTypes of Transmission Lines
1.1. Two wire lineTwo wire line
2.2. Coaxial cableCoaxial cable
3.3. WaveguideWaveguide
RectangularRectangular
CircularCircular
4.4. Planar Transmission LinesPlanar Transmission Lines
Strip lineStrip line
Microstrip lineMicrostrip line
Slot lineSlot line
Fin lineFin line
Coplanar WaveguideCoplanar Waveguide
Coplanar slot lineCoplanar slot line
3. 3
Analysis of differences between Low and HighAnalysis of differences between Low and High
FrequencyFrequency
At low frequencies, the circuit elements are lumpedAt low frequencies, the circuit elements are lumped
since voltage and current waves affect the entire circuitsince voltage and current waves affect the entire circuit
at the same time.at the same time.
At microwave frequencies, such treatment of circuitAt microwave frequencies, such treatment of circuit
elements is not possible since voltag and current waveselements is not possible since voltag and current waves
do not affect the entire circuit at the same time.do not affect the entire circuit at the same time.
The circuit must be broken down into unit sectionsThe circuit must be broken down into unit sections
within which the circuit elements are considered to bewithin which the circuit elements are considered to be
lumped.lumped.
This is because the dimensions of the circuit areThis is because the dimensions of the circuit are
comparable to the wavelength of the waves accordingcomparable to the wavelength of the waves according
to the formula:to the formula:
c/fc/f
where,where,
c = velocity of lightc = velocity of light
f = frequency of voltage/currentf = frequency of voltage/current
5. 5
Metallic Cable Transmission MediaMetallic Cable Transmission Media
• Metallic transmission linesMetallic transmission lines
• Balanced and Unbalanced Transmission LinesBalanced and Unbalanced Transmission Lines
• Metallic Transmission Line Equivalent CircuitMetallic Transmission Line Equivalent Circuit
• Wave Propagation on a Metallic Transmission LineWave Propagation on a Metallic Transmission Line
• Transmission Line LossesTransmission Line Losses
• Phasor Current and VoltagesPhasor Current and Voltages
• Single section of transmission lineSingle section of transmission line
• Characteristic Impedance and PropagationCharacteristic Impedance and Propagation
ConstantConstant
• Standing waves, reflectionStanding waves, reflection
6. 6
Types of Transmission LinesTypes of Transmission Lines
CoaxialCoaxial
Twisted-PairTwisted-Pair
Open-WireOpen-Wire
Twin-LeadTwin-Lead
10. 10
Coaxial componentsCoaxial components
ConnectorsConnectors: Microwave coaxial connectors required to: Microwave coaxial connectors required to
connect two coaxial lines are als calledconnect two coaxial lines are als called connector pairsconnector pairs
(male(male andand female).female). They must match the characteristicThey must match the characteristic
impedance of the attached lines and be designed to haveimpedance of the attached lines and be designed to have
minimum reflection coefficients and not radiate powerminimum reflection coefficients and not radiate power
through the connector.through the connector. E.g. APC-3.5, BNC, SMA, SMCE.g. APC-3.5, BNC, SMA, SMC
Coaxial sectionsCoaxial sections: Coaxial line sections slip inside each: Coaxial line sections slip inside each
other while still making electrical contact. These sections areother while still making electrical contact. These sections are
useful for matching loads and making slotted lineuseful for matching loads and making slotted line
measurements. Double and triple stub tuning configurationsmeasurements. Double and triple stub tuning configurations
are available as coaxial stub tuning sections.are available as coaxial stub tuning sections.
AttenuatorsAttenuators: The function of an attenuator is to reduce the: The function of an attenuator is to reduce the
power of the signal through it by a fixed or adjustablepower of the signal through it by a fixed or adjustable
amount. The different types of attenuators are:amount. The different types of attenuators are:
1.1. Fixed attenuatorsFixed attenuators
2.2. Step attenuatorsStep attenuators
3.3. Variable attenuatorsVariable attenuators
11. 11
Coaxial components (contd.)Coaxial components (contd.)
Coaxial cavities: Coaxial cavities are concentricCoaxial cavities: Coaxial cavities are concentric
lines or coaxial lines with an air dielectric andlines or coaxial lines with an air dielectric and
closed ends. Propagation of EM waves is in TEMclosed ends. Propagation of EM waves is in TEM
mode.mode.
Coaxial wave meters: Wave meters use a cavityCoaxial wave meters: Wave meters use a cavity
to allow the transmission or absorption of ato allow the transmission or absorption of a
wave at a frequency equal to the resonantwave at a frequency equal to the resonant
frequency of the cavity. Coaxial cavities arefrequency of the cavity. Coaxial cavities are
used as wave meters.used as wave meters.
12. 12
AttenuatorsAttenuators
Attenuators are components that reduce the amountAttenuators are components that reduce the amount
of power a fixed amount, a variable amount or in aof power a fixed amount, a variable amount or in a
series of fixed steps from the input to the output of theseries of fixed steps from the input to the output of the
device. They operate on the principle of interfering withdevice. They operate on the principle of interfering with
the electric field or magnetic field or both.the electric field or magnetic field or both.
Slide vane attenuatorsSlide vane attenuators: They work on the principle that a: They work on the principle that a
resistive material placed in parallel with the E-lines of aresistive material placed in parallel with the E-lines of a
field current will induce a current in the material that willfield current will induce a current in the material that will
result inresult in II22
RR power loss.power loss.
Flap attenuatorFlap attenuator: A flap attenuator has a vane that is: A flap attenuator has a vane that is
dropped into the waveguide through a slot in the top ofdropped into the waveguide through a slot in the top of
the guide. The further the vane is inserted into thethe guide. The further the vane is inserted into the
waveguide, the greater the attenuation.waveguide, the greater the attenuation.
Rotary vane attenuatorRotary vane attenuator: It is a precision waveguide: It is a precision waveguide
attenuator in which attenuation follows a mathematicalattenuator in which attenuation follows a mathematical
law. In this device, attenuation is independent onlaw. In this device, attenuation is independent on
frequency.frequency.
13. 13
IsolatorsIsolators
Mismatch or discontinuities cause energy to beMismatch or discontinuities cause energy to be
reflected back down the line. Reflected energy isreflected back down the line. Reflected energy is
undesirable. Thus, to prevent reflected energy fromundesirable. Thus, to prevent reflected energy from
reaching the source, isolators are used.reaching the source, isolators are used.
Faraday Rotational IsolatorFaraday Rotational Isolator: It combines ferrite: It combines ferrite
material to shift the phase of an electromagneticmaterial to shift the phase of an electromagnetic
wave in its vicinity and attenuation vanes towave in its vicinity and attenuation vanes to
attenuate an electric field that is parallel to theattenuate an electric field that is parallel to the
resistive plane.resistive plane.
Resonant absorption isolatorResonant absorption isolator: A device that can be: A device that can be
used for higher powers. It consists of a section ofused for higher powers. It consists of a section of
rectangular waveguide with ferrite material placedrectangular waveguide with ferrite material placed
half way to the center of the waveguide, along thehalf way to the center of the waveguide, along the
axis of the guide.axis of the guide.
14. 14
Metallic transmission linesMetallic transmission lines
Balanced lines have equal impedances from the twoBalanced lines have equal impedances from the two
conductors to groundconductors to ground
Twisted-pair and parallel lines are usually balancedTwisted-pair and parallel lines are usually balanced
Differential, or balanced, transmission systemDifferential, or balanced, transmission system
15. 15
Metallic transmission linesMetallic transmission lines
Differential, or balanced, transmission systemDifferential, or balanced, transmission system
signal voltagessignal voltages noise voltagesnoise voltages
16. 16
Metallic transmission linesMetallic transmission lines
Unbalanced lines usually have one conductor groundedUnbalanced lines usually have one conductor grounded
Coaxial lines usually have outer conductor groundedCoaxial lines usually have outer conductor grounded
Single-ended, or unbalanced, transmission systemSingle-ended, or unbalanced, transmission system
17. 17
Ideal Transmission LineIdeal Transmission Line
No lossesNo losses
conductors have zero resistanceconductors have zero resistance
dielectric has zero conductancedielectric has zero conductance
possible only with superconductorspossible only with superconductors
approximated by a short lineapproximated by a short line
No capacitance or inductanceNo capacitance or inductance
possible with a real line only at dcpossible with a real line only at dc
with low frequencies and short lines thiswith low frequencies and short lines this
can be approximatedcan be approximated
19. 19
Traveling waveTraveling wave
( ) ( )coscv t V tω=
ωω is the angular frequency (rad/sec)is the angular frequency (rad/sec)
The input voltage can be described asThe input voltage can be described as
20. 20
Traveling waveTraveling wave
( ) ( )coscv t V tω=
( ) ( ), coscv z t V t zω β= −
ωω is the angular frequency (rad/sec)is the angular frequency (rad/sec)
The input voltage can be described asThe input voltage can be described as
ββ is the propagation constant (rad/m)is the propagation constant (rad/m)
( ) ( ), cosci z t I t zω β= −
current and voltage are in phase?!?!?current and voltage are in phase?!?!?
The traveling wave can be described asThe traveling wave can be described as
21. 21
Phase velocity and wavelengthPhase velocity and wavelength
( ) ( )coscv t V t zω β= −
2βλ π=
2π
β
λ
=
distance
1time
pv f
f
λ ω
λ
β
= = = =
2 fω π=
The energy travels with the group velocityThe energy travels with the group velocity
g
d
v
d
ω
β
=
22. 22
AttenuationAttenuation
( ) ( ), cosz
cv z t V e t zα
ω β−
= −
αα is the attenuation coefficientis the attenuation coefficient
(nepers/meter)(nepers/meter)
What is the attenuation in dB perWhat is the attenuation in dB per
meter?meter?
23. 23
AttenuationAttenuation
( ) ( ), cosz
cv z t V e t zα
ω β−
= −
αα is the attenuation coefficient (nepers/meter)is the attenuation coefficient (nepers/meter)
What is the attenuation in dB per meter?What is the attenuation in dB per meter?
( ) ( )20log 20 log 8.686dB
m
Att e eα
α α= = =
(One neper is 8.686 dB)(One neper is 8.686 dB)
( ) ( )log logg
a ax g x=
24. 24
Phasor currents and voltagesPhasor currents and voltages
A phasor can be used to represent the amplitude of aA phasor can be used to represent the amplitude of a
sinusoidal voltage or current and is phase difference fromsinusoidal voltage or current and is phase difference from
a reference sinusoid of the same frequency. A phasora reference sinusoid of the same frequency. A phasor
does not include any representation of the frequency.does not include any representation of the frequency.
( ) ( ) ( )cos Rez z j z j t
v t Ve t z Ve e eα α β ω
ω β− − −
= − =
has a phasorhas a phasor VV which can be represented inwhich can be represented in
amplitude-angle form asamplitude-angle form as VV∠φ∠φ,, or in componentor in component
formform a+a+jjbb wherewhere a=Va=Vcoscosφφ andand b=Vb=Vsinsinφφ or in complex-or in complex-
exponential formexponential form j
Ve φ
25. 25
The phasor of the driving voltage isThe phasor of the driving voltage is VV00
The phasor of the voltage at distanceThe phasor of the voltage at distance xx
from the driving point isfrom the driving point is
( )jj xx x x
e e e eα βα β γ− +− − −
= = =x 0 0 0V V V V
wherewhere γγ is the propagation constantis the propagation constant
Phasor currents and voltagesPhasor currents and voltages
jγ α β= +
26. 26
z
z
e
e
γ
γ
−
−
=
=
x 0
x 0
V V
I I
Remember,Remember, II00 andand VV00 are themselves phasors,are themselves phasors,
and their angles are not necessarily the same.and their angles are not necessarily the same.
Phasor currents and voltagesPhasor currents and voltages
jγ α β= +
27. 27
Transmission Line ModelTransmission Line Model
At low frequencies only resistance has toAt low frequencies only resistance has to
be consideredbe considered
At higher frequencies capacitance andAt higher frequencies capacitance and
inductance must be includedinductance must be included
All of these are distributed along the lineAll of these are distributed along the line
28. 28
Iz
GδzCδz
Iz
Iz+δI
Iz+δI
Vz Vz+δV
Total series resistanceTotal series resistance RRδδzz
Total series inductanceTotal series inductance LLδδzz
jR z L zδ δ ω δ= − −z zV I I
( )j
d
R L
dz
ω= − +z
z
V
I
( )j
d
G C
dz
ω= − +z
z
I
V
( )jR Lγ ω= − +z zV I
( )jG Cγ ω= − +z zI V
Single section of transmission lineSingle section of transmission line
C
L
1
j
j
z
z
z
z
e
e
Z
C
Z L
γ
γ
ω
ω
−
−
=
=
=
=
0
0
V V
I I
δI
jI G z C zδ δ ω δ= − −z zV V
δV
29. 29
Characteristic ImpedanceCharacteristic Impedance
Ratio between voltage and current on lineRatio between voltage and current on line
Depends only on line geometry andDepends only on line geometry and
dielectricdielectric
Not a function of lengthNot a function of length
Has units of ohms but not the same as theHas units of ohms but not the same as the
resistance of the wire in the lineresistance of the wire in the line
0Z = z
z
V
I
30. 30
( )jR Lγ ω= − +z zV I ( )jG Cγ ω= − +z zI V
0
j
j
R L
Z
G C
ω
ω
+
= =
+
z
z
V
I
Characteristic ImpedanceCharacteristic Impedance
j
j
R L
G C
ω
ω
+
=
+
z z
z z
V I
I V
ZZ00 is the characteristic impedanceis the characteristic impedance
For an RF lineFor an RF line RR andand GG are zero (valid for high RF frequencies)are zero (valid for high RF frequencies)
0
L
Z
C
= =z
z
V
I
Current and voltage are in phaseCurrent and voltage are in phase
RR = conductor resistance in= conductor resistance in ΩΩ/unit length/unit length
LL = inductance in H/unit length= inductance in H/unit length
GG = dielectric conductance in S/unit length= dielectric conductance in S/unit length
CC = capacitance in F/unit length= capacitance in F/unit length
31. 31
Velocity FactorVelocity Factor
Step moves down line at a finite speedStep moves down line at a finite speed
Velocity cannot be greater than speedVelocity cannot be greater than speed
of light and is usually lowerof light and is usually lower
Velocity factor is ratio between actualVelocity factor is ratio between actual
propagation velocity and speed of lightpropagation velocity and speed of light
Velocity factor depends only on lineVelocity factor depends only on line
dielectricdielectric
32. 32
Velocity FactorVelocity Factor
vvpp = propagation velocity on the line= propagation velocity on the line
cc = speed of light in vacuum= speed of light in vacuum
== 300300 ×× 101066
m/sm/s
c
v
v
p
f =
0 0
1
c
µ ε
=
33. 33
Propagation ConstantPropagation Constant
( )jR Lγ ω= − +z zV I
( )jG Cγ ω= − +z zI V
( ) ( )2
j jR L G Cγ ω ω= + +z z z zV I V I
( ) ( )j jR L G Cγ ω ω= + +
For anFor an ideal lineideal line RR andand GG are zeroare zero
j LCγ ω= purely imaginary and no attenuationpurely imaginary and no attenuation
jγ α β= +
0α =
LCβ ω=
1
pv
LC
=
pv
ω
β
=
34. 34
Metallic transmission linesMetallic transmission lines
Two-wire parallel transmission lineTwo-wire parallel transmission line
0 276log
D
Z
r
=
ZZ00 = the characteristic impedance (ohms)= the characteristic impedance (ohms)
DD = the distance between the centers= the distance between the centers
rr = the radius of the conductor= the radius of the conductor
εε00 = the permittivity of free space (F/m)= the permittivity of free space (F/m)
εεrr = the relative permittivity or dielectric constant of= the relative permittivity or dielectric constant of
the medium (unitless)the medium (unitless)
µµ00 = the permeability of free space (H/m)= the permeability of free space (H/m)
1
p
o
v
µ ε
=
0rε ε ε=
0
1
o
c
µ ε
=
35. 35
Metallic transmission linesMetallic transmission lines
Coaxial cableCoaxial cable
0
138
log
r
D
Z
dε
=
ZZ00 = the characteristic impedance (ohms)= the characteristic impedance (ohms)
DD = the diameter of the outer conductor= the diameter of the outer conductor
dd = the diameter of the inner conductor= the diameter of the inner conductor
ε = the permittivity of the material= the permittivity of the material
εεrr = the relative permittivity or dielectric constant= the relative permittivity or dielectric constant
of the mediumof the medium
µµ00 = the permeability of free space= the permeability of free space
1
p
o
v
µ ε
=
0rε ε ε=
0
1
o
c
µ ε
=
36. 36
Transmission Lines LossesTransmission Lines Losses
• Conductor LossesConductor Losses
•Increases with frequencyIncreases with frequency
due to skin effectdue to skin effect
• Dielectric Heating LossesDielectric Heating Losses
•Also increases withAlso increases with
frequencyfrequency
• Radiation LossesRadiation Losses
• Not significant with goodNot significant with good
quality coax properlyquality coax properly
installedinstalled
• Can be a problem withCan be a problem with
open-wire cableopen-wire cable
• Coupling LossesCoupling Losses
• CoronaCorona Skin effect
39. 39
Step Applied to Infinite LineStep Applied to Infinite Line
Voltage step will propagate down lineVoltage step will propagate down line
Energy is stored in line capacitance andEnergy is stored in line capacitance and
inductanceinductance
Energy from source appears to be dissipatedEnergy from source appears to be dissipated
by line but is really storedby line but is really stored
If line is infinitely long the step never reachesIf line is infinitely long the step never reaches
the endthe end
Voltage and current have definite, finite valuesVoltage and current have definite, finite values
40. 40
Reflection of Voltage StepReflection of Voltage Step
Infinite line: no reflectionInfinite line: no reflection
Finite line with load impedanceFinite line with load impedance ZZLL == ZZ00
no reflectionno reflection
the load looks to the source like an extension ofthe load looks to the source like an extension of
the linethe line
Voltage and currents are compatibleVoltage and currents are compatible
Z =Z = √√(L/C)(L/C)
Finite line with load impedanceFinite line with load impedance ZZLL ≠≠ ZZ00
Some or all of the step will reflect from the loadSome or all of the step will reflect from the load
end of the lineend of the line
41. 41
Reflection of PulsesReflection of Pulses
Transmission LineTransmission Line
Short circuitShort circuit
R0
ReflectionReflection
hyperlinkhyperlink
42. 42
Shorted LineShorted Line
Total voltage at shorted end = 0Total voltage at shorted end = 0
Incident and reflected voltages must beIncident and reflected voltages must be
equal and oppositeequal and opposite
Incident and reflected currents are equalIncident and reflected currents are equal
with same polaritywith same polarity
Time for surge to reach end of line isTime for surge to reach end of line is
T = L/vT = L/vpp
43. 43
Open LineOpen Line
Transmission LineTransmission Line
R0
Reflection of PulsesReflection of Pulses
ReflectionReflection
hyperlinkhyperlink
44. 44
Open-Circuited LineOpen-Circuited Line
Total current at open end = 0Total current at open end = 0
Incident and reflected currents must beIncident and reflected currents must be
equal and oppositeequal and opposite
Incident and reflected voltages are equalIncident and reflected voltages are equal
with same polaritywith same polarity
Time for surge to reach end of line isTime for surge to reach end of line is
T = L/vT = L/vpp
45. 45
Reflection CoefficientReflection Coefficient
More complex situation: Load has an arbitraryMore complex situation: Load has an arbitrary
impedanceimpedance
not equal tonot equal to ZZ00
not shorted or opennot shorted or open
impedance may be complex (either capacitive orimpedance may be complex (either capacitive or
inductive as well as resistive)inductive as well as resistive)
When the ZL ≠ Z0, part of the power is reflected back
and the remainder is absorbed by the load.
46. 46
Reflection CoefficientReflection Coefficient
r r
i i
V I
or
V I
Γ =
ΓΓ = reflection coefficient= reflection coefficient
VVii = incident voltage= incident voltage
VVrr = reflected voltage= reflected voltage
IIii = incident current= incident current
IIrr = reflected current= reflected current
The amount of voltage reflected back isThe amount of voltage reflected back is
calledcalled voltage reflection coefficient.voltage reflection coefficient.
47. 47
ZZLL
Transmission LineTransmission Line
ZZ00
Reflection of PulsesReflection of Pulses
r r
i i
V I
or
V I
Γ @
total voltage i rV V= +
total current i rI I= −
i r
L
i r
V V
Z
I I
+
=
−
0
i r
i r
V V
Z
I I
= =
0
0
L
L
Z Z
Z Z
−
Γ =
+
48. 48
Wave Propagation on LinesWave Propagation on Lines
Start by assuming a matched lineStart by assuming a matched line
Waves move down the line at propagationWaves move down the line at propagation
velocityvelocity
Waves are the same at all points exceptWaves are the same at all points except
for phasefor phase
Phase changes 360 degrees in thePhase changes 360 degrees in the
distance a wave travels in one perioddistance a wave travels in one period
This distance is called the wavelengthThis distance is called the wavelength
49. 49
Standing WavesStanding Waves
When an incident wave reflects from a mismatchedWhen an incident wave reflects from a mismatched
load, an interference pattern developsload, an interference pattern develops
Both incident and reflected waves move at theBoth incident and reflected waves move at the
propagation velocity, but the interference pattern ispropagation velocity, but the interference pattern is
stationarystationary
The interference pattern is called a set of standingThe interference pattern is called a set of standing
waveswaves
It is formed by the addition of incident and reflectedIt is formed by the addition of incident and reflected
waves and has nodal points that remain stationarywaves and has nodal points that remain stationary
with timewith time
52. 52
Standing-Wave RatioStanding-Wave Ratio
When line is mismatched but neitherWhen line is mismatched but neither
open nor shorted, voltage varies alongopen nor shorted, voltage varies along
line without ever falling to zeroline without ever falling to zero
Greater mismatch leads to greaterGreater mismatch leads to greater
variationvariation
Voltage standing-wave ratio (VSWR orVoltage standing-wave ratio (VSWR or
SWR) is defined:SWR) is defined:
min
max
V
V
SWR = (( ≥≥ 1)1)
54. 54
SWR and Reflection CoefficientSWR and Reflection Coefficient
SWR is a positive real numberSWR is a positive real number
ΓΓ may be positive, negative or complexmay be positive, negative or complex
SWRSWR ≥≥ 11
Magnitude ofMagnitude of ΓΓ ≤≤ 11
55. 55
Standing waves on an Open LineStanding waves on an Open Line
This is only the amplitude!!!This is only the amplitude!!!
56. 56
Standing waves on an Shorted LineStanding waves on an Shorted Line
This is only the amplitude!!!This is only the amplitude!!!
57. 57
Effects of High SWREffects of High SWR
High SWR causes voltage peaks onHigh SWR causes voltage peaks on
the line that can damage the line orthe line that can damage the line or
connected equipment such as aconnected equipment such as a
transmittertransmitter
Current peaks due to high SWR causeCurrent peaks due to high SWR cause
losses to increaselosses to increase
58. 58
Reflected PowerReflected Power
When a signal travels down a mismatched line,When a signal travels down a mismatched line,
some of the power reflects from the loadsome of the power reflects from the load
This power is dissipated in the source, if theThis power is dissipated in the source, if the
source matches the linesource matches the line
A high SWR causes the load power to be reducedA high SWR causes the load power to be reduced
59. 59
Reflected PowerReflected Power
PPrr = reflected power= reflected power
PPii = incident power= incident power
PPLL = power delivered to load= power delivered to load
1
1
SWR
SWR
−
Γ =
+
iL
iL
ir
P
SWR
SWR
P
PP
PP
2
2
2
)1(
4
)1(
+
=
Γ−=
Γ=
61. 61
General Input Impedance EquationGeneral Input Impedance Equation
Input impedance of a transmission lineInput impedance of a transmission line
at a distanceat a distance LL from the loadfrom the load
impedance Zimpedance ZLL with a characteristic Zwith a characteristic Zoo isis
Zinput =Zinput = ZZoo [(Z[(ZLL + j Z+ j Zoo BL)BL)
(Z(Zoo + j Z+ j ZLL BL)]BL)]
where B is called phase constant orwhere B is called phase constant or
wavelength constant and is defined bywavelength constant and is defined by
the equationthe equation
B = 2B = 2
62. 62
Half and Quarter wave transmission lines
The relationship of the input impedance at the
input of the half-wave transmission line with its
terminating impedance is got by letting L =
in the impedance equation.
Zinput = ZL
The relationship of the input impedance at the
input of the quarter-wave transmission line with
its terminating impedance is got by letting L =
in the impedance equation.
Zinput = √(Zinput Zoutput)
63. 63
Effect of Lossy line on V and I wavesEffect of Lossy line on V and I waves
The effect of resistance in a transmission line is toThe effect of resistance in a transmission line is to
continuously reduce the amplitude of both incidentcontinuously reduce the amplitude of both incident
and reflected voltage and current waves.and reflected voltage and current waves.
Skin Effect: As frequency increases, depth ofSkin Effect: As frequency increases, depth of
penetration into adjacent conductive surfacespenetration into adjacent conductive surfaces
decreases for boundary currents associated withdecreases for boundary currents associated with
electromagnetic waves, that results in theelectromagnetic waves, that results in the
confinement of the voltage and current waves at theconfinement of the voltage and current waves at the
boundary of the transmission line, thus making theboundary of the transmission line, thus making the
transmission more lossy.transmission more lossy.
Skin depth (m) = 1Skin depth (m) = 1 √√ff
where f = frequency, Hzwhere f = frequency, Hz = permeability, H/m= permeability, H/m
= conductivity, S/m= conductivity, S/m
64. 64
Smith chart
For complex transmission line problems, the
use of the formulae becomes increasingly
difficult and inconvenient. An indispensable
graphical method of solution is the use of
Smith Chart.
65. 65
Components of a Smith ChartComponents of a Smith Chart
HHorizontal lineorizontal line: The horizontal line running through: The horizontal line running through
the center of the Smith chart represents either thethe center of the Smith chart represents either the
resistive or the conductive component. Zeroresistive or the conductive component. Zero
resistance is located on the left end and infiniteresistance is located on the left end and infinite
resistance is located on the right end of the line.resistance is located on the right end of the line.
CCircles of constant resistance and conductanceircles of constant resistance and conductance::
Circles of constant resistance are drawn on the SmithCircles of constant resistance are drawn on the Smith
chart tangent to the right-hand side of the chart andchart tangent to the right-hand side of the chart and
its intersection with the centerline. These circles ofits intersection with the centerline. These circles of
constant resistance are used to locate complexconstant resistance are used to locate complex
impedances.impedances.
LLines of constant reactanceines of constant reactance: Lines of constant: Lines of constant
reactance are shown on the Smith chart with curvesreactance are shown on the Smith chart with curves
that start from a given reactance value on the outerthat start from a given reactance value on the outer
circle and end at the right-hand side of the center line.circle and end at the right-hand side of the center line.
66. 66
Type of Microwave problems that SmithType of Microwave problems that Smith
chart can be usedchart can be used
1.1. Plotting a complex impedance on a Smith chartPlotting a complex impedance on a Smith chart
2.2. Finding VSWR for a given loadFinding VSWR for a given load
3.3. Finding the admittance for a given impedanceFinding the admittance for a given impedance
4.4. Finding the input impedance of a transmission lineFinding the input impedance of a transmission line
terminated in a short or open.terminated in a short or open.
5.5. Finding the input impedance at any distance from aFinding the input impedance at any distance from a
load Zload ZLL..
6.6. Locating the first maximum and minimum from anyLocating the first maximum and minimum from any
loadload
7.7. Matching a transmission line to a load with a singleMatching a transmission line to a load with a single
series stub.series stub.
8.8. Matching a transmission line with a single parallel stubMatching a transmission line with a single parallel stub
9.9. Matching a transmission line to a load with twoMatching a transmission line to a load with two
parallel stubs.parallel stubs.
67. 67
Plotting a Complex Impedance on aPlotting a Complex Impedance on a
Smith ChartSmith Chart
To locate a complex impedance, Z = R+-jX orTo locate a complex impedance, Z = R+-jX or
admittance Y = G +- jB on a Smith chart,admittance Y = G +- jB on a Smith chart,
normalize the real and imaginary part of thenormalize the real and imaginary part of the
complex impedance. Locating the value of thecomplex impedance. Locating the value of the
normalized real term on the horizontal linenormalized real term on the horizontal line
scale locates the resistance circle. Locatingscale locates the resistance circle. Locating
the normalized value of the imaginary term onthe normalized value of the imaginary term on
the outer circle locates the curve of constantthe outer circle locates the curve of constant
reactance. The intersection of the circle andreactance. The intersection of the circle and
the curve locates the complex impedance onthe curve locates the complex impedance on
the Smith chart.the Smith chart.
68. 68
Finding the VSWR for a givenFinding the VSWR for a given
loadload
Normalize the load and plot its location onNormalize the load and plot its location on
the Smith chart.the Smith chart.
Draw a circle with a radius equal to theDraw a circle with a radius equal to the
distance between the 1.0 point and thedistance between the 1.0 point and the
location of the normalized load and thelocation of the normalized load and the
center of the Smith chart as the center.center of the Smith chart as the center.
The intersection of the right-hand side ofThe intersection of the right-hand side of
the circle with the horizontal resistancethe circle with the horizontal resistance
line locates the value of the VSWR.line locates the value of the VSWR.
69. 69
Finding the Input Impedance at anyFinding the Input Impedance at any
Distance from the LoadDistance from the Load
The load impedance is first normalized and isThe load impedance is first normalized and is
located on the Smith chart.located on the Smith chart.
The VSWR circle is drawn for the load.The VSWR circle is drawn for the load.
A line is drawn from the 1.0 point through theA line is drawn from the 1.0 point through the
load to the outer wavelength scale.load to the outer wavelength scale.
To locate the input impedance on a SmithTo locate the input impedance on a Smith
chart of the transmission line at any givenchart of the transmission line at any given
distance from the load, advance in clockwisedistance from the load, advance in clockwise
direction from the located point, a distance indirection from the located point, a distance in
wavelength equal to the distance to the newwavelength equal to the distance to the new
location on the transmission line.location on the transmission line.
70. 70
Power LossPower Loss
Return Power LossReturn Power Loss: When an electromagnetic: When an electromagnetic
wave travels down a transmission line andwave travels down a transmission line and
encounters a mismatched load or aencounters a mismatched load or a
discontinuity in the line, part of the incidentdiscontinuity in the line, part of the incident
power is reflected back down the line. Thepower is reflected back down the line. The
return loss is defined as:return loss is defined as:
PPreturnreturn = 10 log= 10 log1010 PPii/P/Prr
PPreturnreturn = 20 log= 20 log1010 1/1/
Mismatch Power LossMismatch Power Loss: The term mismatch loss: The term mismatch loss
is used to describe the loss caused by theis used to describe the loss caused by the
reflection due to a mismatched line. It is definedreflection due to a mismatched line. It is defined
asas
PPmismatchmismatch = 10 log= 10 log1010 PPii/(P/(Pii - P- Prr))
71. 71
Notes:Notes:
Metallic circuit currentMetallic circuit current – currents that flow in– currents that flow in
opposite directions in a balanced wire pairopposite directions in a balanced wire pair
Longitudinal currentLongitudinal current – currents that flow in the– currents that flow in the
same directionsame direction
Common Mode Rejection (CMR)Common Mode Rejection (CMR) – cancellation– cancellation
of common mode signals or noise interferenceof common mode signals or noise interference
induced equally on both wires producinginduced equally on both wires producing
longitudinal currents that cancel in the loadlongitudinal currents that cancel in the load
CMRR = 40 to 70 dBCMRR = 40 to 70 dB
72. 72
Notes:Notes:
Primary electrical constantsPrimary electrical constants – R, L, C, G– R, L, C, G
Secondary constantsSecondary constants – Zo, Propagation– Zo, Propagation
ConstantConstant
For maximum power transfer, ZFor maximum power transfer, ZLL = Zo, thus no= Zo, thus no
reflectionreflection
Characteristic impedance = Surge impedanceCharacteristic impedance = Surge impedance
Transmission line stores energy in itsTransmission line stores energy in its
distributed inductance and capacitancedistributed inductance and capacitance
73. 73
Notes:Notes:
Transmission lines:Transmission lines:
The input impedance of an infinitely long line at radioThe input impedance of an infinitely long line at radio
frequencies is resistive and equal to Zofrequencies is resistive and equal to Zo
Nonresonant – when electromagnetic waves travelNonresonant – when electromagnetic waves travel
the line without reflectionsthe line without reflections
Ratio of voltage to current at any point is equal to ZoRatio of voltage to current at any point is equal to Zo
Incident voltage and current at any point are in phaseIncident voltage and current at any point are in phase
Line losses on a non-resonant line are minimum perLine losses on a non-resonant line are minimum per
unit lengthunit length
Any transmission line that is terminated in a loadAny transmission line that is terminated in a load
equals to Zo acts as if it were an infinite line.equals to Zo acts as if it were an infinite line.
Prop. Cons. = attenuation coeff. + phase shift coeff.Prop. Cons. = attenuation coeff. + phase shift coeff.
γγ == αα + j+ jββ
76. 76
Notes:Notes:
Velocity factor (Velocity constant) =Velocity factor (Velocity constant) = actual vel. Of prop.actual vel. Of prop.
vel. In free spacevel. In free space
Vf = Vp / cVf = Vp / c
Electrical length of transmission lineElectrical length of transmission line
Long – length exceedsLong – length exceeds λλ/16/16
Short – length less than or equalShort – length less than or equal λλ/16/16
Delay lines – transmission lines designed toDelay lines – transmission lines designed to
intentionally introduce a time delay in the path of anintentionally introduce a time delay in the path of an
electromagnetic waveelectromagnetic wave
td = LC (seconds)td = LC (seconds)
td = 1.016td = 1.016 ЄЄ
77. 77
Notes:Notes:
The disadvantages of not having a matched line:The disadvantages of not having a matched line:
100 percent of the source incident power does not100 percent of the source incident power does not
reach the loadreach the load
The dielectric separating the two conductors canThe dielectric separating the two conductors can
break down and cause corona due to high VSWRbreak down and cause corona due to high VSWR
Reflections and rereflections cause more power lossReflections and rereflections cause more power loss
Reflections cause ghost imagesReflections cause ghost images
Mismatches cause noise interferenceMismatches cause noise interference
78. 78
Notes:Notes:
Characteristics of transmission line terminated at openCharacteristics of transmission line terminated at open
voltage incident wave is reflected back (no phasevoltage incident wave is reflected back (no phase
reversal)reversal)
current incident wave is reflected back 180 degreescurrent incident wave is reflected back 180 degrees
from how it would have continuedfrom how it would have continued
sum of the incident and reflected current waveformssum of the incident and reflected current waveforms
is minimumis minimum
sum of the incident and reflected voltage waveformssum of the incident and reflected voltage waveforms
is maximumis maximum
79. 79
Notes:Notes:
Characteristics of transmission line terminated at shortCharacteristics of transmission line terminated at short
voltage standing wave is reflected back 180 degreesvoltage standing wave is reflected back 180 degrees
reversed from how it would have continuedreversed from how it would have continued
current standing wave is reflected back the same ascurrent standing wave is reflected back the same as
if it had continuedif it had continued
sum of the incident and reflected current waveformssum of the incident and reflected current waveforms
is maximumis maximum
sum of the incident and reflected voltage waveformssum of the incident and reflected voltage waveforms
is zero at the shortis zero at the short
80. 80
InputInput
endend
OutputOutput
endend
λλ/4/4
Zin = resistive, maxZin = resistive, max
Zin = resistive, minZin = resistive, min
Zin = inductiveZin = inductive
Zin = capacitiveZin = capacitive
Zin = capacitiveZin = capacitive
Zin = inductiveZin = inductive
shortshort
openopen
shortshort
openopen
shortshort
openopen
Input ImpedanceInput Impedance
Parallel LC circuit,Parallel LC circuit,
resistive and maximumresistive and maximum
Series LC circuit,Series LC circuit,
resistive and minimumresistive and minimum
inductorinductor
capacitorcapacitor
capacitorcapacitor
inductorinductor
81. 81
Notes:Notes:
The impedance transformation for a quarter wavelengthThe impedance transformation for a quarter wavelength
transmission line is:transmission line is:
RRLL = Zo: quarter= Zo: quarter λλ line acts 1:1 turns ratio transformerline acts 1:1 turns ratio transformer
RRLL > Zo: quarter> Zo: quarter λλ lineline acts as a step down transformeracts as a step down transformer
RRLL < Zo: quarter< Zo: quarter λλ line acts as a step up transformerline acts as a step up transformer
Characteristic Impedance of quarter wavelength X’formerCharacteristic Impedance of quarter wavelength X’former
Zo’ =Zo’ = √(Zo√(ZoZZLL))
When a load is purely inductive oir purely capacitive, noWhen a load is purely inductive oir purely capacitive, no
energy is absorbed, thus,energy is absorbed, thus, ГГ = 1 and SWR = inf.= 1 and SWR = inf.
82. 82
Notes:Notes:
Stub MatchingStub Matching
Stubs are used to eliminate the reactive componentStubs are used to eliminate the reactive component
to match the transmission line to the loadto match the transmission line to the load
It is just a piece of additional transmission line that isIt is just a piece of additional transmission line that is
placed across the primary line as close to the load asplaced across the primary line as close to the load as
possiblepossible
Susceptance of stub is used to tune out theSusceptance of stub is used to tune out the
susceptance of the loadsusceptance of the load
Shorted stubs are preferred because open stubsShorted stubs are preferred because open stubs
have the tendency to radiate at higher frequencieshave the tendency to radiate at higher frequencies
83. 83
Notes:Notes:
Process of Stub MatchingProcess of Stub Matching
locate a point as close to the load as possible wherelocate a point as close to the load as possible where
the conductive component of the input admittance isthe conductive component of the input admittance is
equal to the characteristic admittance of transmissionequal to the characteristic admittance of transmission
line Yin = G – jB, G = 1 / Zoline Yin = G – jB, G = 1 / Zo
Attach the shorted stub to the point on theAttach the shorted stub to the point on the
transmission linetransmission line
Depending whether the reactive component at theDepending whether the reactive component at the
point is inductive or capacitive, the stub length ispoint is inductive or capacitive, the stub length is
adjustedadjusted
Yin = Go – jB + jBstubYin = Go – jB + jBstub
Yin = GoYin = Go
84. 84
Notes:Notes:
Time Domain Reflectometry (TDR)Time Domain Reflectometry (TDR)
technique used to locate an impairment in thetechnique used to locate an impairment in the
metallic cablemetallic cable
How much of the transmitted signal returns dependsHow much of the transmitted signal returns depends
on the type and magnitude of the impairmenton the type and magnitude of the impairment
Impairment represents a discontinuity in the signalImpairment represents a discontinuity in the signal
For higher frequency applications (300 MHz – 3000 MHz),For higher frequency applications (300 MHz – 3000 MHz),
microstrip and stripline is constructed to interconnectmicrostrip and stripline is constructed to interconnect
components on PC boardscomponents on PC boards
When the distance between source and load ends is aWhen the distance between source and load ends is a
few inches or less, coaxial cable is impracticalfew inches or less, coaxial cable is impractical
Microstrip and Stripline use the tracks on the PC board.Microstrip and Stripline use the tracks on the PC board.
85. 85
Notes:Notes:
Microstrip and Stripline are used to constructMicrostrip and Stripline are used to construct
transmission lines, inductors, capacitors, tuned circuits,transmission lines, inductors, capacitors, tuned circuits,
filters, phase shifters, and impedance matching devices.filters, phase shifters, and impedance matching devices.
Microstrip – when the lines are etched in the middleMicrostrip – when the lines are etched in the middle
layer of the multilayer PC boardlayer of the multilayer PC board
Zo =Zo = 8787 lnln 5.98h__5.98h__ ЄЄ fiberglass = 4.5fiberglass = 4.5
√√((ЄЄ + 1.41)+ 1.41) 0.8w + t0.8w + t ЄЄ teflon = 3teflon = 3
w = width of Cu tracew = width of Cu trace
t = thickness of Cu tracet = thickness of Cu trace
h = thickness of dielectrich = thickness of dielectric
Stripline – if the lines are etched onto the surface of theStripline – if the lines are etched onto the surface of the
PC board onlyPC board only
Zo =Zo = 6060 lnln 4d __4d __ d = dielectric thickd = dielectric thick
88. 88
Problems:Problems:
1.1. Determine the characteristic impedance for anDetermine the characteristic impedance for an
air dielectric two-wire parallel transmissionair dielectric two-wire parallel transmission
line with a D/r ratio = 13.5line with a D/r ratio = 13.5 (311.97 ohms)(311.97 ohms)
2.2. Determine the characteristic impedance for anDetermine the characteristic impedance for an
RG-59A coaxial cable with parameters:RG-59A coaxial cable with parameters:
L=0.121L=0.121 μμH/ft, C=30 pF/ft, d=0.042 in., D=0.22H/ft, C=30 pF/ft, d=0.042 in., D=0.22
in, andin, and ЄЄ=2.15=2.15 (63.509 ohms, 67.685 ohms)(63.509 ohms, 67.685 ohms)
3.3. For a given length of RG8A/U coaxial cableFor a given length of RG8A/U coaxial cable
with parameters: C=98.4 pF/m, L=262.45 nH/m,with parameters: C=98.4 pF/m, L=262.45 nH/m,
ЄЄr=2.15. Find Vp and Vfr=2.15. Find Vp and Vf (1.968x10(1.968x1088
m/s, 0.656m/s, 0.656
or 0.682)or 0.682)
89. 89
Problems:Problems:
4.4. For a transmission line with incident voltage ofFor a transmission line with incident voltage of
5.2V and reflected voltage of 3.8V, find5.2V and reflected voltage of 3.8V, find
reflection coefficient and SWRreflection coefficient and SWR (0.731, 6.429)(0.731, 6.429)
5.5. Determine the physical length and Zo for aDetermine the physical length and Zo for a
quarter wavelength transformer that is used toquarter wavelength transformer that is used to
match a section of RG8A/U (Zo=50 ohms) to amatch a section of RG8A/U (Zo=50 ohms) to a
175 ohm resistive load. The frequency of175 ohm resistive load. The frequency of
operation is 220 MHz and the velocity factor isoperation is 220 MHz and the velocity factor is
11 (0.341 m, 93.54 ohms)(0.341 m, 93.54 ohms)
90. 90
Stub MatchingStub Matching
Use to remove the reactive component of theUse to remove the reactive component of the
complex impedance of the load to match thecomplex impedance of the load to match the
transmission line to the loadtransmission line to the load
It is a piece of additional transmission line that isIt is a piece of additional transmission line that is
placed across the primary line as close to the loadplaced across the primary line as close to the load
as possibleas possible
The susceptance of the stub is used to tune out theThe susceptance of the stub is used to tune out the
susceptance of the loadsusceptance of the load
Either a shorted or open stub is used with greaterEither a shorted or open stub is used with greater
preference on the shorted stubpreference on the shorted stub
A transmission line that is one-half wavelength orA transmission line that is one-half wavelength or
shorter is used to tune out the reactive componentshorter is used to tune out the reactive component
of the loadof the load
91. 91
Stub Matching ProcessStub Matching Process
1.1. Locate a point as close as possible to the loadLocate a point as close as possible to the load
where the conductive component of the Zwhere the conductive component of the Zinin = Z= Zoo
YYinin = G – jB where G = 1 / Z= G – jB where G = 1 / Zoo
2.2. Attach the shorted stub on the identified pointAttach the shorted stub on the identified point
3.3. Depending on whether the reactive component atDepending on whether the reactive component at
that point is inductive or capacitive, the stub lengththat point is inductive or capacitive, the stub length
is adjusted accordinglyis adjusted accordingly
YYinin = G= Goo – jB + jB– jB + jBstubstub
~ Y~ Yinin = G= Goo