Penetrating concrete sealers and concrete densifiers guaranteed to waterproof, strengthen, and protect concrete for a lifetime.

2. Foundation Armor TM
Sealers
Foundation Armor TM professional-grade concrete
sealers are highly concentrated, non-
toxic, penetrating, permanent sealers specifically
formulated to seal, strengthen, and protect
concrete, brick, cement, and other masonry surfaces.
Foundation Armor TM sealers undergo a chemical
reaction with the free calcium and lime naturally found
in concrete, brick, and masonry – dramatically
enhancing their natural characteristics and reducing
the capillary voids to practically zero.
Foundation Armor TM sealers don’t alter, stain, discolor
or change the texture of the surface. They can be used
on interior and exterior, above/below grade
applications, and on vertical and horizontal surfaces.

3. FOUNDATION ARMOR TM SEALERS STOP: FOUNDATION ARMOR TM SEALERS INCREASE:
 Water and vapor migration up to 100psi •Overall strength, hardness, and density by up to 45%
 Moisture vapor transmission up to .015 WVT •Bond strength of epoxies, paints, and stains by up to
 Alkali attack and efflorescence attack
20%
FOUNDATION ARMOR TM SEALERS REDUCE:
 Transmission of hazardous gases, including FOUNDATION ARMOR TM SEALERS:
Radon NEVER peel, flake, or fade
 The absorption of
chemicals, chlorides, solvents, fats and oils NEVER stain from exposure to UV rays
 Internal chlorides by up to 50%-90% NEVER leave behind a slippery surface coating
NEVER have to be re-applied or maintained
FOUNDATION ARMOR TM SEALERS PREVENT:
 The growth of
mold, mildew, bacteria, lichen, and moss
 Flaking, cracking, scaling and spalling
caused during freeze-thaw cycles
 Surface deterioration and discoloration

4. Water plus cement produces Calcium Silicate Hydrate (C-S-H) in a
process known as Hydration. C-S-H is the binding system for
concrete. Combined with the aggregate, C-S-H gives concrete its
hardness and strength.
A reactive byproduct of the Hydration process is Calcium Hydroxide.
When a Foundation Armor concrete sealer is applied to
concrete, it reacts with the existing Calcium Hydroxide to produce
additional C-S-H. This additional C-S-H is what provides the
increased hardness and densification by up to 45%, and water
resistance up to 100 PSI.
Foundation Armor concrete sealers have the highest percentage of
reactive material, and are optimized to make the silicate available
more quickly for more rapid C-S-H formation.

5.  Armor S1000 TM
 Penetrates concrete up to 2”
 Proprietary Sodium Silicate Blend
 2 Coat Application, 24-Hour Dry Time
 Armor S2000 TM
 Penetrates concrete up to 4”
 Proprietary Sodium Silicate PLUS Blend
 2 Coat Application, 24-Hour Dry Time
 Armor L3000 TM
 Penetrates concrete up to 2”
 Proprietary Lithium Silicate Blend
 1 Coat Application, 6-Hour Dry Time

6. Armor S1000 TM
The Armor S1000 TM is a permanent sealer that penetrates up to 2” into the substrate.
Retail: $109.95/Gallon
Armor S1000 TM – Where To Use
The Armor S1000 TM concrete sealer can be used on:
 Interior and exterior concrete, above and below grade.
 Vertical and horizontal uncoated concrete surfaces.
 Poured concrete, concrete bricks, concrete blocks, concrete slabs, concrete
pavers, and stamped concrete.
 New and old concrete.
 Concrete with water, moisture, vapor, and radon permeability issues.
Armor S1000 TM – Preparation
 New concrete must cure for a minimum of 28 days.
 Concrete must be free of paints, stains, oils, chemicals, sealers, and dyes.
 Remove any efflorescence, mold, or mildew prior to application.
 Surface can be swept or power washed prior to application.
Armor S1000 TM – Application
 Dilute Armor S1000 TM sealer with 3 parts warm to hot water.
 Using a garden sprayer, spray on surface of concrete.
 Immediately following the first coat (wait at least 30-45 minutes
between coats), apply a second coat.
 Roll out any puddles with a brush or roller, or wipe up an excess
materials with a clean cloth.
 Use product when temperature is between 50-900F (10-320C).
Armor S1000 TM Dry Time
Let dry 24 hours.
Armor S1000 TM Coverage
One gallon of the Armor S1000 TM is diluted with 3 parts warm water and covers up to 1,250 square feet. For old or porous concrete, or for
applications that require a third coat, expect one gallon to cover up to 700 square feet.

7. Armor S2000 TM
The Armor S2000 TM is a permanent sealer that penetrates up to 4” into the substrate.
Retail: $129.95/Gallon
Armor S2000 TM – Where To Use
The Armor S2000 TM concrete sealer can be used on:
 Interior and exterior concrete, above and below grade.
 Vertical and horizontal uncoated concrete surfaces.
 Poured concrete, concrete bricks, concrete blocks, concrete slabs, concrete
pavers, and stamped concrete.
 New and old concrete.
 Concrete with water, moisture, vapor, and radon permeability issues.
Armor S2000 TM – Preparation
 New concrete must cure for a minimum of 28 days.
 Concrete must be free of paints, stains, oils, chemicals, sealers, and dyes.
 Remove any efflorescence, mold, or mildew prior to application.
 Surface can be swept or power washed prior to application.
Armor S2000 TM – Application
 Dilute Armor S2000 TM sealer with 3 parts warm to hot water.
 Using a garden sprayer, spray on surface of concrete.
 Immediately following the first coat (wait at least 30-45 minutes
 between coats), apply a second coat.
 Roll out any puddles with a brush or roller, or wipe up an excess
 materials with a clean cloth.
 Use product when temperature is between 50-900F (10-320C).
Armor S2000 TM Dry Time
Let dry 24 hours.
Armor S2000 TM Coverage
One gallon of the Armor S2000 TM is diluted with 3 parts warm water and covers up to 1,250 square feet. For old or porous concrete, or for
applications that require a third coat, expect one gallon to cover up to 700 square feet.

8. Armor L3000 TM
The Armor L3000 TM is a permanent sealer that penetrates up to 4” into the substrate.
Retail: $149.95/Gallon
Armor L3000 TM – Where To Use
The Armor L3000 TM concrete sealer can be used on:
 Interior and exterior concrete, above and below grade.
 Vertical and horizontal uncoated concrete surfaces.
 Poured concrete, concrete bricks, concrete blocks, concrete slabs, concrete
pavers, and stamped concrete.
 New and old concrete.
 Concrete with water, moisture, vapor, and radon permeability issues.
Armor L3000 TM – Preparation
 New concrete must cure for a minimum of 28 days.
 Concrete must be free of paints, stains, oils, chemicals, sealers, and dyes.
 Remove any efflorescence, mold, or mildew prior to application.
 Surface can be swept or power washed prior to application.
Armor L3000 TM – Application
 Dilute Armor L3000 TM sealer with 1 part warm to hot water.
 Using a garden sprayer, saturate the surface of concrete.
 Roll out any puddles with a brush or roller, or wipe up an excess
materials with a clean cloth.
 Use product when temperature is between 50-900F (10-320C).
Armor L3000 TM Dry Time
Let dry 6 hours.
Armor L3000 TM Coverage
One gallon of the Armor L3000 TM is diluted with 1 part warm water and covers up to 900 square feet. For old or porous concrete, or for
applications that require a third coat, expect one gallon to cover up to 700 square feet.

9. Foundation Armor TM
We hope you have enjoyed the
presentation. Please visit
FoundationArmor.com for
access to our brochures and
special programs.
Foundation Armor
866-306-0246
FoundationArmor.com