This PowerPoint helps students to consider the concept of infinity.
Building construction report
1. BUILDING CONSTRUCTION II ( BLD 60703/ARC 2513 )
PROJECT 1:
SKELETAL CONSTRUCTION (Temporary bus station)
Yew Wing Kee
Chong Yi Hui
Vun Tze Lin
Wong Cho Mun
Tung Siew Hui
0323555
0324404
0323301
0322723
0323823
Tutor : Mr. Mohamed Rizal Mohamed
1
2. INDEX
I. Abstract
II. Design Process
III. Design Consideration
IV. Skeletal Structure
V. Material Selection
VI. Axonometric
VII. Construction Detail
VIII. Joints
IX. Structural Strength
X. Orthographic drawings
2
3. CHONG YI HUI 0324404
TUNG SIEW HUI 0323823
VUN TZE LIN 0323301
WONG CHO MUN 0322723
YEW WING KEE 0323555
4. ABSTRACT : SKELETAL CONSTRUCTION
Skeletal Construction is one of the widely used structures for building support, thus it is important for us to
experience and gain knowledge to understand it. A skeletal structure is in which weight is conveyed by a
framework, rather than being upheld by walls. A frame is a structure used to resists vertical forces such as
gravity, rain, dead and live load and also resists lateral forces such as wind.
For this assignment, we were assigned into groups to construct a temporary bus stop in a scale 1:5 to
demonstrate our insight into skeletal structure in and applying the use of recyclable materials relating with its
function.
After exploring on different types of materials for our shelter, we decided to use timber and steel joints for
our skeletal structure. Timber is an easily renewed material which can be recycled after usage.
4
5. DESIGN PROCESS
MOCK UP 1
Scale: 1:50
A small model is made to show the joints
connection and for better understanding of the
structure.
MOCK UP 2
Scale: 1 : 1
An improvised to scale digital model is made for
clearer understanding of the skeletal structure
and materials used.
5
6. DESIGN PROCESS
MOCK UP 3 ：INTERIM MOCK UP
Scale: 1: 1
This model is used for interim showing the
structure of the bus stop. We used
modeling board to try out different joints
and connections to test it’s workability. This
is used as our finalised design with
improvised joints and structure.
6PERSPECTIVE AND ORTHOGRAPHIC DRAWINGS
7. DESIGN CONSIDERATION
Weather Resistant
The design of our bus stop is
to accommodate with our
tropical climate, where the
users would be protected
from direct sunlight and also
rain.
Ventilation
Openings throughout the bus
stop to ensure the users
receive sufficient ventilation.
Assesibility
The bus stop can only be
accessed through the front
to enable a ‘one-way’
circulation.
Function
The function of the bus stop
varies, depending on the
users themselves. It works
as a shed and resting area
for users while waiting for
their bus.
7
9. MATERIAL SELECTION
The materials used for our shelter is one of the important
factor to ensure our building structural strength. We used
wood for our temporary shelter, as wood is a readily available
material which can be renewed.
Our group sourced our recycled wood from the leftovers of
the carpentry workshop, and our joint connectors from
hardware shop.
Plastic corrugated roof decking is used as an alternative
material metal roof decking because it is easily combined, the
decking panels are mechanically fastened
9
10. MATERIAL SELECTION
Timber (Recycled Wood)
Advantages
➔ Excellent insulator: Bricks also known to have outstanding insulating
properties, but timber managed to surpass them.
➔ Easy and fast to build: A timber construction can be built very easy and fast in
contrast to a common brick or concrete construction.
➔ Reusable: Timber is a renewable resource. Timber can be used more than
once. It is easy to recycle
➔ Price: Timber construction is cheaper than any other common procedure.
➔ Strength: Timber is very light but Timber framings are strong in real structural
terms.
➔ Aesthetic appeal: Timber is a beautiful material for both internal and external
appearance. 10
11. MATERIAL SELECTION
Timber (Recycled Wood)
Disadvantages
➔ Shrinking and swelling: Timber has a natural ability to absorb water.
➔ Fire resistance: If timber has not passed a special treatment which ensure a
special fire rating, timber is highly combustable.
➔ Discolouration: With the time untreated timber which is exposed to the
different weather influences it discolours turns to a dark and dirty optic.
➔ Mouldiness: If timber is treated wrong or the installation is not regulated
accordingly, timber has the ability to mould.
11
12. MATERIAL SELECTION
Transparent polycarbonate corrugated roofing
Advantages
➔ Better optical properties: It is only corrugated plastic roofing sheets which will
guarantee a more sustainable property. Semi-translucent semi corrugated plastics to
create skylights so that no need to turn on electricity during the day since this
material will allow sufficient amount of light during the day.
➔ Low maintenance costs: Corrugated plastics are extremely easy to clean thus.
➔ They are durable: Most corrugated plastic roofing sheets are coated with anti-scratch
coating and ultraviolet protection.
➔ Cost effectiveness: Economically, it is perfect choice for both short-term and long-
term investment. The installation process is pretty simple and not labor intensive.
Disadvantages
➔ Initial Expenses: It is quite expensive due to the advantages above.
12
13. MATERIAL SELECTION
Concrete pad footing
Advantages
➔ High Compressive strength if compared to other materials
➔ Withstand tensile stress
➔ Fire and water and water resistant
➔ Ability to cast into shape
➔ Concrete ingredients are easily and readily available
Disadvantages
➔ Without reinforcement, it cracks easily
➔ Sustained loads forms creep in structures 13
15. CONSTRUCTION DETAIL: Joints
Clip angles for superimposed
beams; provide for lateral
stability
Dado joint will be used to
hold the beam and column
together and then secured
with brackets
Rabbet joints is used to
connect the floor to the
column
The flooring of the bus stop
is secured with lap joints.
The flooring is nailed to the
floor joist.
15
16. JOINTS
16
MORTISE AND TENON
Mortise and tenon joints were used for the
bracings structure to ensure the stability of the
structure. Mortise and tenon is a basic form which
is simple yet strong. The tenon is cut to fit the
mortise hole exactly and usually has shoulders
that seat when the joint fully enters the mortise
hole. It is used mainly when the adjoining pieces
connect at an angle 90˚.
17. 17
LAP JOINTS
Lap joints is used for the X bracing and also
the floor joist. A lap joint is a joint which
used on wood, plastic or metal. The floor
joist is overlapped then secured with L
brackets.
18. ROOF JOINTS
To maximise watertightness, always
place roof screws through the crests.
For walling. Crest fixing is used to instal
roof sheeting. A more detailed view is
shown in the diagram.
18
19. STRUCTURAL STRENGTH
19
Skeletal load transfer - Two way system
● Uniform load distributed in two direction
● Force is channeled from beams to column
External Forces - Loads
● Static load
- The weight of the roof structure is distributed to the column
● Dynamic load
- When users get on and off the structure
The main load is carried by the the beams and columns. Load is distributed
evenly throughout the structure, with suitable joints and connections the
structure can be strengthened. Bracings are added to increase lateral and
vertical rigidity.
23. 23
FORMWORK AND CONCRETE SETTING FOR PAD FOOTING
MODEL ASSEMBLING
CONCRETE IS MIXED WITH SAND GRAVEL MIXED CONCRETE CASTED INTO THE
FORMWORK
THE WOOD WAS THEN BEING ASSEMBLED BY SCREWING AND DRILLING THEM
26. REFERENCE
Ching, F. (2014). Building construction illustrated. Hoboken, NJ: Wiley.
https://www.pinterest.com/pin/520939881887632147/
McKay, W. B., & McKay, J. K. (1975). Building construction. London: Longman.
Lecture slides
26
27. CONCLUSION
In this assignment, we were given the task to construct a temporary bus shelter in order to
present our knowledge of the skeletal structure in and applying the usage of recyclable
materials relating to its function. The building process should demonstrate the
understanding of skeletal frames and its joints. Besides that, it should clearly express all
building elements such as column, roof, walls, and floor. The joints which we apply should
reflect actual joints. Lastly, the model is to be built in the scale 1:5.
Throughout this project, we manage to get the grasp of the skeletal construction to analyse
the subject of strength and stability of structures including the modes of structural system,
forces, stress and strain of skeletal structures. We also learnt how to overcome the force and
stress applied to a structure with suitable construction methods.
27
