Dissertation in RF Engineering (Presented - 01-10-10)

•

2 recomendaciones•601 vistas

sanslides

MSc - Mobile Communication Dissertation by Sankar Velama

Design of 3-dB Band Pass Filtered Power Divider SankarVelama --- 0926188 MSc Mobile Communications Supervisor : Dr. Kenneth Yeo

To achieve the response of the band pass filter & the power divider simultaneously.

To achieve desired circuit & microstrip layout.

To simulate the design & present it’s results.

To make the analysis & find out the future enhancements.,[object Object]

The proposed diagram represents how the complexity of a conventional design can be reduced.,[object Object]

3rd Order Band Pass Filter using Chebyshev prototype ,[object Object]

Circuit model implementationSpread Sheet for all the Calculations

Schematic of a 3rd order band pass filter Agilent ADS was used to design the circuit & microstrip layouts.

J-inverter model for 3rd order band pass filter ,[object Object],[object Object]

Más contenido relacionado

La actualidad más candente

Dynamic sub arrays for Hybrid Precoding in Wide Band Millimeter Wave Wireless...

Abdul Qudoos

Design of multiband microstrip patch antenna for wireless application

IRJET Journal

This paper has introduced the concept of UWB antenna in array arrangements. The four elements of Balance Antipodal Vivaldi Antenna (BAVA) has been used for planar and H-plane array configuration in this research. Each single element of BAVA Antenna is printed on the glass-reinforced epoxy laminate material (FR4) along an overall thickness of 1.57mm and εr=4.3 respectively. The optimized measurement of each particular element is 60.75mm x 66mm approximatel. Further the parametric evaluation of four BAVA elements in different planes has been observed in this paper. The placement of array elements has almost coverd entire UWB frequency range and appropriate reflection coefficient which is better than -10dB has been established in both combinations. According to simulation results, the array elements in planar arrangement presenting a suitable reflection and works well at 3.2GHz frequency while the arrangement in H-plane the array elements works well at 7GHz of frequency. In planar arrangement, the operating frequency of antenna elements is shifting as results of the distance among inter elements which increase in wavelength. In H-plane arrangement an antenna elements generate additional gain up to 10.2 dB with good radiation patterns as compared to the planar plane. The CSTMWS simulation software has been used for antenna structural design and parametric verification.

Design and parametric evaluation of UWB antenna for array arrangement

journalBEEI

IRJET - Energy Efficient Enhanced K-Means Cluster-Based Routing Protocol for WSN

IRJET Journal

In this paper, we obtain the basic configuration of the left-hand circular polarization (LHCP) array two patches stack triangular truncated microstrip antenna. This construction use the basic corporate feed microstrip-line with modified lossless T-junction power divider on radiating patch for circularly polarized-synthetic aperture radar (CP-SAR) sensor embedded on airspace with compact, small, and simple configuration. The design of Circular Polarization (CP) is realized by truncating the whole three tips and adjusting the parameters of antenna at the resonant frequency, f=5.2 GHz. The results of characteristic performance and S-parameter for the LHCP array two patches stack antenna at the resonant frequency show successively about 7.24 dBic of gain, 1.99 dB of axial ratio (Ar), and -11.43 dB of S-parameter. Moreover, the impedance bandwidth and the 3 dB-Ar bandwidth of this antenna are around 560 MHz (10.77%) and 50 MHz (0.96%), respectively.

Development of patch stack antenna for CP-SAR sensor

journalBEEI

Electrically controlled frequency reconfigurable comb type antenna is presented in this paper. Reconfigurability is achieved by placing a PIN diode in each slot of the comb type antenna. The proposed antenna has very compact size and works on 8 different bands depending upon the state and number of PIN diode (ON/OFF). Ansoft Designer 7 is used to simulate the equivalent model for the PIN diode and proposed antenna is fabricated on FR4 substrate using photolithography process. As the antenna reconfigure its resonating frequency from 1st band to 8th band, directivity increases from 3.28 to 4.02 and radiation efficiency increases from 75.3% to 93.45% due to the improvement in impedance matching at higher band.

Electrically Controlled Frequency Reconfigurable Comb Type Antenna for Wirele...

IDES Editor

Due to the ever-increasing power demand, the need of electricity and eco-friendly power in every nook and corner of the world, many reaserch topics have been devoted to deal with this problematic. This paper is taking part of the proposed solutions with the presentation of a novel 5.8 GHz rectenna system for wireless power transmission applications. In one hand, a miniaturized 5.8 GHz circular polarized patch antenna has been designed and simulated by using the Advanced Design System (ADS). In the other hand, a rectifier structure has been investigated and optimized by the use of the Harmonic Balance method available in ADS. The circuit is based on 5 HSMS2820 Schottky diodes implemented in a voltage multiplier topology and a load resistance of 1 KOhm. Both of the structures have been validated by simulation and experimental results and good agreement has been concluded.

A new design of a microstrip rectenna at 5.8 GHz for wireless power transmiss...

IJECEIAES

Filtering Antennas: Synthesis and Design

IRJET Journal

Design and Development of High Gain Patch Antenna Array for ISM Applications

IRJET Journal

A novel miniaturized multiband, single-feed microstrip patch antenna is presented in this paper for WLAN and WiMAX applications. Both size reduction and multiband are obtained by etching the Multiple Complementary Split Ring Resonators (MC-SRR) on the ground plane of the normal patch antenna. At first, the normal patch antenna produces a single band of 5.15 GHz; 200 MHz (5.0500~5.2499). Subsequently, a Single Circular Split Ring Resonator (SC-SRR) is etched on the ground plane and produces a triple band of: 3.25 GHz; 288 MHz (3.1085~3.3964), 4.5 GHz; 101.3 MHz (4.4488~4.5501), and 5.22 GHz; 220 MHz (5.1191~5.3400) and Double Single Circular Split Ring Resonator (DC-MCSRR) with: 2.99 GHz; 60.7 MHz (2.9574~3.0181), 3.57 GHz; 324.7 MHz (3.4065~3.7312), and 5.1413 GHz; 115.4 MHz (5.0817~5.1971). The working bandwidths cover the desired frequency bands of WLAN 5.2 GHz and WiMAX 3.3/3.5 GHz. The proposed (MC-SRR) antenna can be employed to wireless communication systems due to its simplicity in design, compactness and miniaturization.

Design of Miniaturized Multiband Patch Antenna Using CSRR for WLAN/WiMAX Appl...

TELKOMNIKA JOURNAL

11 an-efficient-vlsi-architecture-of-a-reconfigurable-pulse-shaping-fir-inter...

Pvrtechnologies Nellore

The VHF/UHF band radar that using circular array antennas is a novel kind of radar, whose performances, such as angular accuracy, angular resolution, anti-jamming and low-altitude coverage capabilities are better than the conventional VHF/UHF band radar. On one hand, we focus on how the directivity of array element will influence upon the array pattern. The performance characteristics of the single microstrip patch antenna can be further enhanced by using microstrip patch antenna array. On the other hand, in order to lower the side lobe level (SLL) of circular array antennas , we investigate the effectiveness of amplitude-weighted methods including Taylor Window and Gaussian Window.

SIDE LOBE REDUCTION OF CIRCULAR ARRAY USING TAYLOR DISTRIBUTION FUNCTION IN ...

IAEME Publication

Intelligent reflecting surface 3

VARUN KUMAR

Intelligent reflecting surface 2

VARUN KUMAR

A simplified space vector pulse-width modulation (SVPWM) for three-phase cascaded H-bridge (CHB) inverters is presented in this paper. Treating each unit as a three-level inverter and adopting serial calculation mode, a CHB inverter is modulated unit by unit using three-level SVPWM. Duty cycles of real sector are obtained by mapping duty cycles of sector 1, in which the calculation of three-level SVPWM is done. The process to implement multilevel SVPWM is simplified to the process to implement three-level SVPWM. By reusing FPGA chip resource which is used for the calculation of three-level SVPWM, the presented SVPWM can be easily adopted to a CHB inverter with different number of units, while the FPGA chip resource utilization is reduced significantly. In addition, the presented SVPWM provides an effective switching frequency higher than the switching frequency of IGBTs. Simulation and experimental results are provided to verify the feasibility of the presented SVPWM.

A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...

Asoka Technologies

Ib3614041408

IJERA Editor

Ijetcas14 375

Iasir Journals

Advanced Modeling Method for UHF Broadcast Slotted Coaxial Antennas

Brandon George

La actualidad más candente (18)

Dynamic sub arrays for Hybrid Precoding in Wide Band Millimeter Wave Wireless...

Design of multiband microstrip patch antenna for wireless application

Design and parametric evaluation of UWB antenna for array arrangement

IRJET - Energy Efficient Enhanced K-Means Cluster-Based Routing Protocol for WSN

Development of patch stack antenna for CP-SAR sensor

Electrically Controlled Frequency Reconfigurable Comb Type Antenna for Wirele...

A new design of a microstrip rectenna at 5.8 GHz for wireless power transmiss...

Filtering Antennas: Synthesis and Design

Design and Development of High Gain Patch Antenna Array for ISM Applications

Design of Miniaturized Multiband Patch Antenna Using CSRR for WLAN/WiMAX Appl...

11 an-efficient-vlsi-architecture-of-a-reconfigurable-pulse-shaping-fir-inter...

SIDE LOBE REDUCTION OF CIRCULAR ARRAY USING TAYLOR DISTRIBUTION FUNCTION IN ...

Intelligent reflecting surface 3

Intelligent reflecting surface 2

A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...

Ib3614041408

Ijetcas14 375

Advanced Modeling Method for UHF Broadcast Slotted Coaxial Antennas

Destacado

Current Fiamma Wine List 12.21.09

guest1d3610

755

grazi87

Alex edca presentation＿2011_0725

chunwei

H60 C School Graduation, Top of the Class.PDF

Kenth Santibanez Rivera

Sr. Engineer (Design & Application) - HVAC & Automotive(1)

Ankit Sarvaiya

3.1.1 b

pruebados

Patiño universo miercoles y domingo

Presidencia de la República del Ecuador

estrategias y tecnicas de estudio

Jonh Llamoca Martinez

Optometric optics

OPTOM FASLU MUHAMMED

Toxocara canis in children

Maulood Turfah

estratégias y técnicas de estudio

Jonh Llamoca Martinez

Sustainability and Safety in Tunnels

Fathi Tarada

Marketing Pricple

Haz Aline

making an magazine with XP-practices

Kenji Hiranabe

Negociação

Celso Crivelaro

Ch20

mcfalltj

Data Mining & Signal Detection In Pv

Until ROI

Tecnica delle Costruzioni - Esercitazione 7 (parte 2) & 8

Franco Bontempi Org Didattica

CONTEXTUALIZACIÓN DE FENÓMENOS SOCIALES, POLÍTICOS Y ECONÓMICOS 1

pruebados

Prisms

Paarth Gera

Destacado (20)

Current Fiamma Wine List 12.21.09

755

Alex edca presentation＿2011_0725

H60 C School Graduation, Top of the Class.PDF

Sr. Engineer (Design & Application) - HVAC & Automotive(1)

3.1.1 b

Patiño universo miercoles y domingo

estrategias y tecnicas de estudio

Optometric optics

Toxocara canis in children

estratégias y técnicas de estudio

Sustainability and Safety in Tunnels

Marketing Pricple

making an magazine with XP-practices

Negociação

Ch20

Data Mining & Signal Detection In Pv

Tecnica delle Costruzioni - Esercitazione 7 (parte 2) & 8

CONTEXTUALIZACIÓN DE FENÓMENOS SOCIALES, POLÍTICOS Y ECONÓMICOS 1

Prisms

Similar a Dissertation in RF Engineering (Presented - 01-10-10)

A Novel Planar Three Way Power Divider

Sachin Kumar Asokan

Jannatul Ferdous_2_resume

Jannatul Ferdous

This proposed work investigates the effects of biasing circuit in the ultra-wideband microwave low noise amplifier which operates between 3GHz to 10GHz. The complete circuit is visualized the importance of every component in the design with respect to linear measurements like Gain, Noise Figure, Return loss under unconditionally stable condition. The design and realization are made by using Hybrid Microwave integrated circuit in AWR microwave office. The thing that is absolutely necessary and frequently the difficult step in the design of an LNA is 'biasing circuit design'. The difficulty situation arises because traditional methods LNA by using S-parameters data files in EDA tools provides almost all linear measurements. Hence a number of time consuming iterations of different biasing circuits with optimization methods may be required to reach targeted specifications with the fixed operating point at the desired points in the load line. Considering this behavior, various alternate biasing circuit schemes are prepared and founded the results associated with it. Furthermore, this paper unmistakably clarifies the impacts of the biasing circuit by utilizing intermodulation and harmonics distortion technique for portrayal characterization. Different cases and sorts of the biasing circuits with various biasing focuses have been tested and given clear perspective of the biasing ideas.

The Approach on Influence of Biasing Circuit in Wideband Low Noise Amplifier ...

IJEACS

A compact microstrip parallel coupled line filter for ultra wide band applications by means of combining a network of coupled line and defected ground is proposed. The design equations for three and five interconnected networks are derived and implemented. Simulations for three different configurations for filters are optimized. Then three prototype circuits are constructed, a bandpass filter with center frequency 2.25 GHz and two different bandpass filters (in terms of perturbations) with center frequencies 2.33GHz. For 2.25 GHz circuit wide fractional bandwidth of about 90% is obtained but undesired high return loss existed. For 2.33GHz circuit with grooves in sides fractional bandwidth of about 60% is obtained at about 3.4 GHz center frequency. However undesired return loss existed for this circuit whereas good out off or 2.33GHz circuit with grooves in whole sections the center frequency got shifted to about 3.4 GHz and about 50% fractional bandwidth is obtained with very good out off band performance observed.

MICROSTRIP COUPLED LINE FILTER DESIGN FOR ULTRA WIDEBAND APPLICATIONS

jmicro

M.sc. m kamel

Ashraf Aboshosha

Edge-Coupled Bandpass Microstrip Filter Design

Rashad Alsaffar

Edge-Coupled Bandpass Filter Design

Rashad Alsaffar

In this paper, a simple mail box design of a dual band microstrip patch antenna, is proposed, designed, fabricated and measured for wireless LAN communications. The proposed antenna is designed using the TLC 30 (TACONIC) substrate, with a relative permittivity of 4.3 and substrate height of 1.6mm. It is designed to operate at 2.44 GHz and 5. 30 GHz respectively. The proposed antenna is the size of 31mm x 34mm x1.6mm and is incited by a 50 Ω micro strip feed line. The characteristics of the antenna are designed and the performance of the modelled antenna is evaluated using CST Microwave Studio. The return loss, radiation patterns and peak antenna gain of 6.5 dBi for frequency 2.44 GHz and 6.2 dBi for 5.30 GHz is separately and successfully plotted. The fabricated prototype exhibits an agreement between the measured and simulated return loss.

Simple Mail Box Design of Dual Band Microstrip Patch Antenna for Wireless LAN...

journalBEEI

Phase shifter is a key component in phase array antenna for the Radar application and the wireless communication system. This paper presents a novel design of miniaturised 2bits phase shifter using Koch fractal shapes of one iteration orders. The 3-section branch line coupler is used to extend the bandwidth of the phase shifter,this type of coupler is characterised by a low cost and simplicity of fabrication.Using the Koch fractal geometry the circuit size of the coupler is reduced to 6.36cm ×2.14cm at 2.4GHz. The simulation results show a good performance. So, over 2.1GHz-2.7GHzThe novel design of 2bits fractal reflection phase shifter based on the 3section show a return loss less than -20dB and the phase error varied between 0.1° and 0.4°for the four output phases . The circuit size of the phase shifter is reduced to9.5cm×2.1cm.

Modelling And Miniaturization of A 2-Bits Phase Shifter Using Koch Fractal Sh...

IJERA Editor

This paper presents the design of CT ΣΔ modulator which can provide high DR and SNR over a 20 MHz signal bandwidth. So far all the CT SDM uses either feedback or feedforward loop filter architecture. The proposed topology is a 3rd order low-pass sigma-delta modulator, which employs a combination of feedforward and feedback schemes. Loop filter is designed as RC integrators due to its high linearity and easy interface. The design starts from system level using Matlab/Simulink. Then, the first integrator in the loop, which is the most critical block in the modulator, is implemented at transistor level using Cadence Virtuoso 180 nm CMOS technology.

Design of Continuous Time Multibit Sigma Delta ADC for Next Generation Wirele...

IJERA Editor

International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.

T044069296

IJERA Editor

Design of delta sigma modulators for integrated sensor applications

Alexander Decker

Abstract This paper presents the simulation architecture and performance analysis with the use of ZCD technic. A Zero-Crossing based All-Digital Baseband Demodulation architecture is proposed in this work. This architecture supports demodulation of all modulation schemes including MSK, PSK, FSK, and QAM. The proposed structure is very low area, low power, and low latency and can operate in real-time. Moreover it can switch, in run-time, between multiple modulation schemes like GMSK (GSM), QPSK (CDMA), GFSK (Bluetooth), 8-PSK (EDGE), Offset-QPSK (W-CDMA), etc. In addition, the phase resolution of the demodulator is scalable with performance. In addition, bit-wise amplitude quantization based quad-decomposition approach is utilized to demodulate higher order M-ary QAM modulations such as 16-QAM & 64-QAM, which is also a highly scalable architecture. This structure of demodulator provides energy-efficient and resource-efficient implementation of various wireless standards in physical layer of SDR. Keywords — Physical layer, Mobile and Wireless Communication, Software Defined radio (SDR), Zero Cross Detection (ZCD), Modulation Schemes, Architecture, high level synthesis, FPGA.

Efficient reconfigurable architecture of baseband demodulator in sdr

eSAT Journals

The presented work intends to encounter the challenge of optimizing frequency tracking in the C-band WLAN spectrum, with a tuning range and phase noise (PN) performance. A Quadrature Voltage Controlled Oscillator (QVCO) design in 130 nm CMOS technology has been presented to cover the most sought WLAN/WiFi spectrum of modern wireless systems, employing the current reuse technique and an on-chip inductor implementation. To provide better compensation of LC losses at reduced power dissipation, a cross-coupled structure combining NMOS and PMOS has been used.We have run an extensive simulation using the industry-standard ADS (Keysight technology) platform. The simulation study attributed to the superior phase noise performance of − 160 dBc/Hz at 1 MHz (near f max) at a power dissipation of 6.52 mW from 1.2 V supply. With the moderate voltage tuning range, the entire desired frequency span of 5.400–5.495 GHz was obtained with a fairly high resolution of 2.375 MHz/1 mV, which allows serving a larger crowd for this spectrum. A fairly moderate VCO gain along with the obtained phase noise and power dissipation provides a well-established Figure of Merit (FOM) of − 187 dB. Finally, a comparison study in terms of power dissipation, phase noise, tuning range, voltage tuning, and Kvco is performed to demonstrate that the provided work is considerably more significant than traditional efforts.

Low Power LC-Quadrature VCO with Superior Phase Noise Performance in 0.13 μmR...

VIT-AP University

res9b

Hyun Yoon

3D Beamforming

Khalid Hussain

SEMINAR[2].pptx automatic circuit design

ShaelMalik

A design and optimization of 3-5 GHz single ended Radio Frequency (RF) Low Noise Amplifier (LNA) for ultra-wide-band (UWB) applications using standard UMC 0.18 µm CMOS technology is reported. Designing of RF circuit components is a challenging job, since even after performing lengthy calculations and finding parameter values it is less guarantee that the design performs as expected. In view of this the optimization tool; Elitist Non-Dominated Sorting Genetic Algorithm (NSGA-II); has been employed to get the optimized starting values of components in the proposed LNA design. The obtained NSGA-II parameters were simulated using Cadence Spectre- RF simulator. The designed Low Noise Amplifier achieves a power gain of 22 dB and a minimum Noise Figure of 3 dB is achieved. It dissipates 12.5 mW of power out of 1.8 V supply

OPTIMIZATION OF CMOS 0.18 M LOW NOISE AMPLIFIER USING NSGA-II FOR UWB

VLSICS Design

The quantum-dot cellular automata (QCA) has more advantages than CMOS regarding area and power. This work targets a conservative reversible comparator and its realization in QCA. In this work, we construct a conservative reversible comparator with an optimal value of reversible metrics. In state to design, three conservative reversible gates, namely PPC, PPNG-1 and PPNG-2 (PP = parity-preserving, C = comparator, N = new, G = gate), are proposed. Furthermore, the quantum equivalent of 1-bit and 2-bit comparator is presented. The proposed concept has been implemented through an algorithm for the n-bit comparator. Also, PPC workability is tested in QCA. The PPC has been performing 1-bit comparator result with minimum area, cell complexity, and latency, which is found to be 0.52 m2, 387 and 1 respectively. In addition, the complete energy dissipation analysis to explore such as a thermal layout map of PPC is also presented in this paper. Further, average energy dissipation v’s kink energy, maximum energy dissipation v’s kink energy, minimum energy dissipation v’s kink energy and average output node polarization v’s temperature are provided in this paper. The proposed comparator forwards an improved ratio of 33.33% in gate count and ranging from 27.27% to 29.35% in garbage outputs than its counterparts circuits, which ensure more scalable.

Designing Conservative Reversible N-Bit Binary Comparator for Emerging Quantu...

VIT-AP University

The paper aims at designing of two stage cascaded ultra-wideband (UWB) low noise amplifier (LNA) by using negative image amplifier technique. The objective of this article is to show the performance improvement using negative image amplifier technique and realization of negative valued lumped elements into microstrip line geometry. The innovative technique to realize the negative lumped elements are carried out by using Richard’s Transformation and transmission line calculation. The AWR microwave office tool is used to obtain characteristics of UWB LNA design with hybrid microwave integrated circuit (HMIC) technology. The 2-stage cascaded LNA design using negative image amplifier technique achieves average gain of 23dB gain and low noise figure of less than 2dB with return loss less than -8dB for UWB 3-10GHz. The Proper bias circuit is extracted using DC characteristics of transistor at biasing point 2V, 20mA and discussed in detail with LNA layout. The negative image matching technique is applied for both input and output matching network. This work will be useful for all low power UWB wireless receiver applications.

Negative image amplifier technique for performance enhancement of ultra wideb...

IJECEIAES

Similar a Dissertation in RF Engineering (Presented - 01-10-10) (20)

A Novel Planar Three Way Power Divider

Jannatul Ferdous_2_resume

The Approach on Influence of Biasing Circuit in Wideband Low Noise Amplifier ...

MICROSTRIP COUPLED LINE FILTER DESIGN FOR ULTRA WIDEBAND APPLICATIONS

M.sc. m kamel

Edge-Coupled Bandpass Microstrip Filter Design

Edge-Coupled Bandpass Filter Design

Simple Mail Box Design of Dual Band Microstrip Patch Antenna for Wireless LAN...

Modelling And Miniaturization of A 2-Bits Phase Shifter Using Koch Fractal Sh...

Design of Continuous Time Multibit Sigma Delta ADC for Next Generation Wirele...

T044069296

Design of delta sigma modulators for integrated sensor applications

Efficient reconfigurable architecture of baseband demodulator in sdr

Low Power LC-Quadrature VCO with Superior Phase Noise Performance in 0.13 μmR...

res9b

3D Beamforming

SEMINAR[2].pptx automatic circuit design

OPTIMIZATION OF CMOS 0.18 M LOW NOISE AMPLIFIER USING NSGA-II FOR UWB

Designing Conservative Reversible N-Bit Binary Comparator for Emerging Quantu...

Negative image amplifier technique for performance enhancement of ultra wideb...