Arquitectura Moderna Le Corbusier- Mies Van Der Rohe
Taller2
1. TALLER AUTOCAD
CONSTRUCCION
DE LA PLANTA ALTA
27
TALLER 02 • PLANTA ALTA
Taller 020 2 | P L A N T A A L T A
02.1.
COPIAR
1Abra el dibujo de
la planta baja.
2Copie el dibujo de
la planta baja y
ubíquelo sobre ésta
(Figura 01).
3Borre las abertu-
ras del garage y
los sombreados (Figu-
ra 02).
4Haga un Zoom sobre
el baño y trace
una línea en el cen-
tro de la curva (Fi-
gura 03).
5Dibuje una línea
hacia la derecha a
0.40 mtrs. de separa-
ción, que abarque el
ancho de la curva.
Command: _line
Specify first point: _from
Base point: _endp of
<Offset>: @0.40,0
ENTER
Specify next point or [Un-
do]: _per to
Specify next point or [Un-
do]: ENTER
FIGURA 01:
Copiar la planta baja.
FIGURA 02:
Borrar entidades.
FIGURA 03:
Línea auxiliar.
01
02
03
2. TALLER AUTOCAD
28
FIGURA 04:
Línea paralela.
FIGURA 05:
Utilización de Offset (Equidistante).
a
b
05
06
07
04
6Con el comando Offset (Equidistante) copie
ésta línea hacia la derecha y la línea del
interior de la pared.
Command: _offset
Specify offset distance or [Through] <Through>: 0.20
ENTER
Select object to offset or <exit>:
Specify point on side to offset:
Select object to offset or <exit>:
Specify point on side to offset:
Select object to offset or <exit>:
ENTER
7Convierta la línea que cruza al baño en lí-
nea continua y utilizando los comandos Ex-
tend (Extensión) y Trim (Recortar) haga las
terminaciones de las líneas recién construidas.
8Utilizando el comando Mirror (Espejar) co-
pie la sección del baño dibujada anterior-
mente.
Command: _mirror
Select objects: Specify opposite corner: 7 found
ENTER
Select objects:
Specify first point of mirror line: _nea to
Specify second point of mirror line: _nea to
Delete source objects? [Yes/No] <N>:
ENTER
9Borre la puerta y dibuje un arco desde las
esquinas de la entrada vieja (Figura 08).
FIGURA 06:
Utilización de los comandos Extend
(Extensión) y Trim (Recortar).
FIGURA 07:
Espejado del baño.
3. Command: _arc Specify start point of arc or [CEnter]:
_endp of
Specify second point of arc or [CEnter/ENd]: _from Base
point: _endp of <Offset>: @0.40,-0.3
ENTER
Specify end point of arc: _endp of
29
TALLER 02 • PLANTA ALTA
08
Command: _extend
Current settings: Projection=UCS Edge=None
Select boundary edges ...
ENTER
Select objects:
ENTER
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]:
ENTER
11Utilice nuevamente el comando Offset
(Equidistante) para copiar la línea de la
pared interior del baño del lado derecho.
Command: _offset
Specify offset distance or [Through] <0.1500>: ENTER
Select object to offset or <exit>:
Specify point on side to offset:
Select object to offset or <exit>:
ENTER
Command:
OFFSET
Specify offset distance or [Through] <0.1500>: 0.05
ENTER
Select object to offset or <exit>:
Specify point on side to offset:
Select object to offset or <exit>:
ENTER
10Con el comando Offset (Equidistante) y
luego Extend (Extensión) construya el es-
pesor del arco (Figura 09).
Command: _offset
Specify offset distance or [Through] <0.2000>: 0.15
ENTER
Select object to offset or <exit>:
Specify point on side to offset:
Select object to offset or <exit>:
ENTER
09
a
b
c
FIGURA 08:
Construcción del arco.
FIGURA 09:
Espesor del arco.
4. FIGURA 10:
Construcción de espacio.
FIGURA 11:
Desplazamiento.
FIGURA 12:
Extensión de líneas.
TALLER AUTOCAD
30
12Realice un zoom a la parte delantera y
dibuje una línea auxiliar en el centro de
la casa. Desplace la pared superior de la
parte de abajo (Figura 11).
Command: _move
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects:
Specify base point or displacement: _endp of
Specify second point of displacement or <use first point as
displacement>: _from Base point: _per to
<Offset>: @0,-0.30
ENTER
13Extienda las líneas hasta la parte des-
plazada y elimine el cuadrado de la co-
lumna.
** STRETCH **
Specify stretch point or [Base point/Copy/Undo/eXit]:
_endp of
12
10
11
a
c
a
b
b
5. 31
TALLER 02 • PLANTA ALTA
14Construya y cierre el dibujo en la parte
izquierda de la sección de abajo.
Command: _stretch
Select objects to stretch by crossing-window
or crossing-polygon...
Select objects: Specify opposite corner: 4 found
Select objects:
Specify base point or displacement:
Specify second point of displacement: @0,-0.1 ENTER
Command: _mirror
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects:
Specify first point of mirror line: _mid of
Specify second point of mirror line: _per to
Delete source objects? [Yes/No] <N>:
ENTER
a
c
e
f
b
d
FIGURA 13: Cierre del dibujo
Desplazamiento
6. TALLER AUTOCAD
32
Command: _move
Select objects:
Specify opposite corner: 5 found
Select objects:
Specify base point or displacement: _endp of
Specify second point of displacement or <use first point as
displacement>: _endp of
Command: _extend
Current settings: Projection=UCS Edge=None
Select boundary edges ...
Select objects:
ENTER
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]:
ENTER
a
c
e
f
b
d
15Desplace la sección opuesta (arriba, si-
métrica) hacia arriba y borre la pared
del medio (Figura 14).
Command: _move
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total
Select objects:
Specify base point or displacement: _endp of
Specify second point of displacement or <use first point as
displacement>: @0,0.20 ENTER
Command: _erase
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total
Select objects: 1 found, 4 total
Select objects: ENTER
FIGURA 14: Construcción del placard
7. 33
TALLER 02 • PLANTA ALTA
Select objects: Specify opposite corner: 3 found
Select objects:
Specify base point or displacement: _endp of
Specify second point of displacement: _from Base point:
_endp of <Offset>: @-0.65,0 ENTER
17Desde la abertura de abajo dibuje con el
comando Rectangle (Rectángulo) el espacio
para una ventana.
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _from Base point: _endp of <Offset>:
@1.225,0 ENTER
Specify other corner point: @1.20,-0.30 ENTER
a
c
e
f
b
d
FIGURA 15: Modificación del dibujo
16Desplace la pared de abajo del Placard
enfrentada a éste último, y extiéndala.
Command: _stretch
Select objects to stretch by crossing-window or crossing-
polygon...
Select objects:
Specify opposite corner: 5 found
Select objects:
Specify base point or displacement: _endp of
Specify second point of displacement: _from Base point:
_endp of <Offset>: @0,0.6 ENTER
Command: _stretch
Select objects to stretch by crossing-window or crossing-
polygon...
f
f
8. TALLER AUTOCAD
34
FIGURA 16:
Dibujo del espacio de la ventana.
FIGURA 17:
Construcción de la escalera en la
planta alta.
FIGURA 18:
Construcción del conducto de humos
de la chimenea.
Command: _extend
Current settings: Projection=UCS Edge=None
Select boundary edges ...
Select objects: 1 found
Select objects:
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]:
ENTER
16
a
b
18Haga un zoom en la sección de la escale-
ra y el pasillo.
19Primero construya la subida y tape la
bajada de la escalera.
Command: _extend
Current settings: Projection=UCS Edge=None
Select boundary edges ...
Select objects: ENTER
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]: ENTER
Command:
Command: _trim
Current settings: Projection=UCS Edge=None
Select cutting edges ...
Select objects: 1 found
Select objects:
Select object to trim or [Project/Edge/Undo]:
Select object to trim or [Project/Edge/Undo]: ENTER
Command: _offset
Specify offset distance or [Through] <0.0500>: 0.20
ENTER
Select object to offset or <exit>:
Specify point on side to offset:
Select object to offset or <exit>: ENTER
a
c
b
17
9. 35
Command: _trim
Current settings: Projection=UCS Edge=None
Select cutting edges ...
Select objects: 1 found
Select objects:
Select object to trim or [Project/Edge/Undo]:
Select object to trim or [Project/Edge/Undo]:
Select object to trim or [Project/Edge/Undo]:
Select object to trim or [Project/Edge/Undo]: ENTER
Command: _extend
Current settings: Projection=UCS Edge=None
Select boundary edges ...
Select objects: 1 found
Select objects:
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]:
Select object to extend or [Project/Edge/Undo]:
ENTER
TALLER 02 • PLANTA ALTA
20Dibuje la chimenea circular y borre los
rectángulos.
Command: _line
Specify first point: _mid of
Specify next point or [Undo]: _per to
Specify next point or [Undo]:
ENTER
Command: _circle
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:
_from Base point: _endp of <Offset>: @-0.20,0
ENTER
Specify radius of circle or [Diameter]: d
ENTER
Specify diameter of circle: 0.25
Command: _.erase 2 found
ENTER
Command: _offset
Specify offset distance or [Through] <Through>: 0.03
ENTER
Select object to offset or <exit>:
Specify point on side to offset:
Select object to offset or <exit>:
ENTER
18
a
c
ba e
d
Conductos
10. a
TALLER AUTOCAD
36
21Haga un zoom en la parte trasera de la
casa y borre los espesores de la pared y
las ventanas (trasera y lateral)
Command: _erase
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total
Select objects: 1 found, 4 total
Select objects: 1 found, 5 total
Select objects: 1 found, 6 total
Select objects: 1 found, 7 total
Select objects: 1 found, 8 total ENTER
22Desde la puerta superior construya un
pequeño rectángulo y cópielo con el co-
mando Array (Matriz) ubicado en la barra de
herramientas Modify (Modificar) (Figura 20).
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _endp of
Specify other corner point: @0.08,-0.0250 ENTER
a
b
b
c
21
FIGURA 19:
Eliminar los espesores de
las paredes y ventanas.
FIGURA 20:
Ubicación del comando
Array (Matríz).
FIGURA 21:
Dibujo de parantes
del ventanal.
20
FIGURA 19: Eliminación de espesores
Array
19
11. 37
TALLER 02 • PLANTA ALTA
Command: _array
Select objects: 1 found
Select objects:
Enter the type of array [Rectangular/Polar] <R>: r
ENTER
Enter the number of rows (—-) <1>: 8
ENTER
Enter the number of columns (|||) <1> 1
ENTER
Enter the distance between rows or specify unit cell (—-): -
0.825
ENTER
23Cambie al layer aberturas.
24Elimine todas las puertas y en su lugar
dibuje una ventana de 0.90, 0.08 mtrs. y
otra para la parte trasera de 0.8, 0.08 met-
ros. Luego conviértalas en bloque.
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]:
Specify other corner point: @0.08,0.9 ENTER
Command: _block
Select objects: Specify opposite corner: 1 found
Select objects: Specify insertion base point:
Command: _insert
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]:
Specify rotation angle <0>:
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _from Base point: _endp of <Offset>: @0,-
0.20 ENTER
Specify other corner point: @-0.08,-0.6 ENTER
23
a
b
b
a
FIGURA 23: Ventana delantera
Ventanas
22
FIGURA 22: Inserción de las ventanas
12. FIGURA 24:
Construcción de los ventanales traseros.
TALLER AUTOCAD
38
Command:
INSERT
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _endp of
Command:
INSERT
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _endp of
Command:
INSERT
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _endp of
ENTER
25Introduzca los bloques de las puertas
construidas en la planta baja en la en-
trada del baño, y para los dormitorios cons-
truya una de 0.08, 0.70 metros.
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _from Base point: _endp of <Offset>:
@0.08,0 ENTER
Specify other corner point: @0.70,0.08 ENTER
Command: _arc
Specify start point of arc or [CEnter]: _endp of
Specify second point of arc or [CEnter/ENd]: e
ENTER
Specify end point of arc: _endp of
Specify center point of arc or [Angle/Direction/Radius]: d
ENTER
Specify tangent direction for the start point of arc: <Ortho on>
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _endp of
Specify other corner point: @0.08,0.8 ENTER
Command: _block
Select objects: 1 found
Select objects:
Specify insertion base point: _endp of
Command: _insert
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _endp of
Command: INSERT
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _endp of
Command: INSERT
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _endp of
Command: INSERT
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _endp of
Command:
INSERT
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _endp of
a
c
b
24
ventanales
P
13. 39
TALLER 02 • PLANTA ALTA
Command: _block
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: Specify insertion base point:
26Construya una ventana de 0.10, 1.20 me-
tros.
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _endp of
Specify other corner point: @1.2,-0.10 ENTER
26
25
a
c f
d
eb
FIGURA 26: Dibujo de ventana
PuertasFIGURA 25: Construcción de puertas
14. 27Pase al layer paredes y en el garage de-
je solamente el contorno.
28Dentro del área del baño utilice el co-
mando Offset (Equidistante) y copie la
curva exterior hacia adentro.
Command: _offset
Specify offset distance or [Through] <0.0300>: 0.05
ENTER
Select object to offset or <exit>:
Specify point on side to offset:
Select object to offset or <exit>:
ENTER
29Ejecute el comando Hatch (Sombreado) y
con las mismas opciones de la planta ba-
ja: ANSI 31 y una escala de 0.030. Inserte el
sombreado en el interior de las paredes de la
casa.
TALLER AUTOCAD
40
27
28
a
b
FIGURA 27:
Contorno del garage.
FIGURA 28:
Construcción de ventanal curvo.
30En la figura 29 vemos el plano terminado
de la planta alta.
FIGURA 29: Planta alta
29
Hemos alcanzado la segunda etapa:
los planos de la planta alta están
terminados. A continuación vamos a
construir las vistas.